Anolis Divine 160 RGBW User manual

Version 1.1

Divine 160 RGBW
2
Table of contents
1. Safety instructions ...................................................................................................................................................... 3
2. Fixture exterior view ................................................................................................................................................... 5
3. Installation .................................................................................................................................................................. 6
3.1 Connection to the mains ...................................................................................................................................... 6
3.2 Mounting the fixture ............................................................................................................................................ 8
4. Divine 160 RGBW - DMX protocol ............................................................................................................................. 9
5. Control menu ............................................................................................................................................................ 12
5.1 Fixture Address ................................................................................................................................................... 12
5.2 Fixture information ............................................................................................................................................. 12
5.3 Personality .......................................................................................................................................................... 13
5.4 Manual mode ...................................................................................................................................................... 15
5.5 Test sequences ................................................................................................................................................... 15
5.6 Stand-alone setting ............................................................................................................................................. 16
5.7 Special functions ................................................................................................................................................. 17
6. Technical specifications ............................................................................................................................................ 19
7. Cleaning and maintenance ....................................................................................................................................... 21
7.1 Replacing a fuse .................................................................................................................................................. 21
7.2 Disposing of the product .................................................................................................................................... 21

Divine 160 RGBW
3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR Divine 160 RGBW!
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure
safe operation, it is absolutely necessary for the user to follow the safety instructions and warnings written in this
manual.
The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual
or any unauthorized modification to the device.
Unauthorized modification will void warranty.
This device is for professional use only. It is not for household use.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT!
Make sure that the available voltage is not higher than stated on the rear side of the fixture.
This fixture should be operated only from the type of power source indicated on the marking label. If you are not
sure of the type of power supplied, consult your authorized distributor or local power company.
Always disconnect the fixture from AC power before servicing or cleaning internally.
Do not overload supply line as this can result in fire or electric shock.
Make sure the power/data cable is never crimped or damaged by sharp edges. Check the fixture and the
power/data cable from time to time.
Do not install the unit near an open flame.
Refer servicing to qualified service personnel.
This fixture falls under protection class I. Therefore, this fixture has to be connected to a mains socket outlet
with a protective earthing connection.
Do not connect this fixture to a dimmer pack.
Warning! Risk Group 2 LED product according to EN 62471 .
LED light emission. Risk of eye injury.
Do not look straight at the fixture´s LEDs during operation. The intense light beam may damage your eyes.
The light source contains blue LEDs.
Keep combustible materials at least 0.3 m away from the fixture.

Divine 160 RGBW
4
If the fixture has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on
immediately. The arising condensation of water might damage your device. Leave the device switched off until it
has reached room temperature.
Avoid brute force when installing or operating the fixture.
When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat or dust.
Avoid using the unit in locations subject to possible impacts.
Only operate the fixture after having checked that the housing is firmly closed and all screws are tightly fastened.
Do not block the front glass cover with any object when the fixture is under operation.
The fixture body must never be covered with cloth or other materials.
The fixture becomes very hot during operation. Allow the fixture to cool approximately 30 minutes prior to
servicing or maintenance.
Operate the fixture only after having familiarized yoursef with its functions. Do not permit operation by persons
not qualified to operate the fixture. Most damages are the result of unprofessional operation!
Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons!
Please use the original packaging if the fixture is to be transported.
If this device will be operated in any way different to the one described in this manual, the product may suffer
damages and the warranty becomes void. Furthermore, any other operation may lead to dangers like short-circuit,
burns, electric shock etc.

Divine 160 RGBW
5
2. Fixture exterior view
Note: customer can interchange the cable glands and blind flanges in the fixture base to create a side or rear
connection.
1.
Head with LED array
2. Tilt lock
3. Base
4. Cable glands or blind flange (depends on fixture version)
5. Surface Mounting adapter
Side
connection shown
Rear connection shown

Divine 160 RGBW
6
3. Installation
3.1 Connection to the mains
Fixtures must be installed by a qualified electrician in accordance with all national
and local electrical and construction codes and regulations.
This device falls under class one and must be grounded!
To connect the Divine 160 RGBW to mains and a DMX controller, use a 5-cored cable Flamar Li9YC11Y. The 3 cores
serve for the power supply and 2 shielded cores are intended for DMX connection:
Core
Connection
Core
Connection
Black
Live
(L)
Red
Data + (+)
White
Neutral
(N)
White
Data
–
(
-
)
Yellow/Green
GND
PE ( )
Shielding
Data ground (0)
1. Unscrew the eight screws (2) on the terminal block cover (1) to get access to the terminal block and
control display (6) with four control buttons (7).
2. Unscrew both cable glands (4) from the terminal block cover (1) and both blind flanges (10) from the
fixture base.
3. Apply an adequate layer of the paste LOCTITE 5331 on the plastic holder of the cable gland before
inserting it into the body of the gland. Apply an adequate layer of the paste LOCTITE 577 on the thread of
the gland body. Screw both cable glands (4) back into the terminal block cover (1) - see the picture below.
4. Apply an adequate layer of the paste LOCTITE 577 on the thread of the blind flange. Screw both blind
flanges (10) back into the fixture base.
5. Pass the power/data cable through one cable gland (4) and connect to the terminal block.
6. Remove end cap (3) from cable glands before passing cable into the terminal block compartment. The two
cable glands serve for cables of diameter of 5-10 mm.
To keep declared IP rating, every cable gland has to be covered with an end cap (3) if the cable gland is not
used for cable passing.

Divine 160 RGBW
7
Note: If you are interchanging cable glands (4) and blind flanges (10), do not forget to apply LOCTITE 5331
and 577 on cable glands and LOCTITE 577 on blind flanges.
7. After connecting cables and setting the fixture by means of the control display and four buttons, place the
cover (1) on the terminal block back, make sure the seal (5) is inserted correctly.
8. Screw the terminal block cover (1) with eight screws using a tightening torque of 7Nm.
9. Check that all cable glands and screws and blind flanges are firmly secured.
Rear connection shown
Side connection shown

Divine 160 RGBW
8
Base technical features of the ABB terminal block:
Type: DS 2,5/10.4L (4 springs mini blocks)
Parameter
IEC
UL/SCA
Rated voltage
800 V
600 V
Rated current
24 A
15 A
Wire size rated/gauge
2.5mm
2
/A2
12AWG
Wire stripping length
9.5 mm
3.2 Mounting the fixture
The Divine 160 RGBW can be arranged in any position/orientation without altering its operation characteristics.
The LED module can be tilted to desired position by means of the tilt lock. Use an Allen key 6 to adjust desired tilt
position.
Screw the surface mounting adapter (11) to the base of the fixture by means of the six screws M8x20 (8).
Four slots (9) in the surface mounting adapter serve for mounting on a non-flammable flat surface via four
screws.
Ensure that the structure to which you are attaching
the fixture is secure.
Caution: Overhead installation requires experience. Fixtures may cause severe injuries when crashing down! If you
have doubts concerning the safety of a possible installation, do not install the device and consult installation with
an expert.

Divine 160 RGBW
9
4. Divine 160 RGBW - DMX protocol
Version 1.2
Mode 1
Channel
Mode 2*
Channel
Value
Function
Type of
control
1 1
0-19
20-24
25-29
30-39
40-49
50-59
60-69
70-89
90-99
100-109
110-119
120-129
130-255
Special functions
Reserved
To activate following functions , stop in DMX value
for at least 3 sec.
Corresponding menu items are temporily overrided.
Display On
Display Off
RGBW colour mixing mode
CMY colour mixing mode
Colour calibration mode On
Colour calibration mode Off
Reserved
Dimmer curve: linear
Dimmer curve: square law
White count On
White count Off
Reserved
step
step
step
step
step
step
step
step
step
step
2
-
0-255
Red
–
all zones
Red LEDs saturation control (0-100%)
proportional
3
-
0-255
Green
–
all zones
Green LEDs saturation control (0-100%)
proportional
4
-
0-255
Blue
–
all zones
Blue LEDs saturation control (0-100%)
proportional
5
-
0-255
White
–
all zones
White LEDs saturation control (0-100%)
proportional
-
2
0-255
Red
-
zone 1
Red LEDs saturation control (0-100%)
proportional
-
3
0-255
Green
-
zone 1
Green LEDs saturation control (0-100%)
proportional
-
4
0-255
Blue
-
zone 1
Blue LEDs saturation control (0-100%)
proportional
-
5
0-255
White
-
zone 1
White LEDs saturation control (0-100%)
proportional
-
6
0-255
Red
zone 2
Red LEDs saturation control (0-100%)
proportional
-
7
Green
-
zone 2

Divine 160 RGBW
10
0
-
255
Green LEDs saturation control (0
-
100%)
proportional
-
8
0-255
Blue
-
zone 2
Blue LEDs saturation control (0-100%)
proportional
-
9
0-255
White
-
zone 2
White LEDs saturation control (0-100%)
proportional
-
10
0-255
Red
-
zone 3
Red LEDs saturation control (0-100%)
proportional
-
11
0-255
Green
-
zone 3
Green LEDs saturation control (0-100%)
proportional
-
12
0-255
Blue
-
zone 3
Blue LEDs saturation control (0-100%)
proportional
-
13
0-255
White
-
zone 3
White LEDs saturation control (0-100%)
proportional
-
14
0-255
Red
-
zone 4
Red LEDs saturation control (0-100%)
proportional
-
15
0-255
Green
-
zone 4
Green LEDs saturation control (0-100%)
proportional
-
16
0-255
Blue
-
zone 4
Blue LEDs saturation control (0-100%)
proportional
-
17
0-255
White
-
zone 4
White LEDs saturation control (0-100%)
proportional
6 18
0
1-255
CT0
-
all zones
No function
Colour temperature correction
step
proportional
7 19
0
1-2
3
4-5
6
7-9
10-12
13-15
16
17-55
56
57 - 95
96
97 – 134
135
136 - 174
Virtual colour wheel
-
all zones
No function
White 2700 K
White 2700 K (tungsten emulation)**
White 3200 K
White 3200 K (tungsten emulation)**
White 4200 K
White 5600 K
White 8000 K
Blue (Blue=full, Red+Green+White=0)
Red=0, Greenup,Blue =full, White=0
Light Blue (Red=0, Green=full, Blue =full, white=0)
Red=0, Green=full, Bluedown, White=0
Green (Red=0, Green=full, Blue =0, White=0)
Redup, Green=full, Blue=0, White=0
Yellow (Red=full, Green=full, Blue=0,White=0)
Red=full, Greendown, Blue=0, White=0
step
step
step
step
step
step
step
step
step
proportional
step
proportional
step
proportional
step
proportional

Divine 160 RGBW
11
175
176 -214
215
216 - 246
247
248-251
252-255
Red
(Red=full
, Green=0, Blue=0, White=0)
Red=full, Green=0, Blueup, White=0
Magenta (Red=full, Green=0, Blue=full, White=0)
Reddown, Green=0, Blue=full, White=0
Blue (Red=0, Green=0, Blue=full, White=0)
Rainbow effect( with fade time) from min.->max. speed
Rainbow effect(without fade time)from min.->max.speed
step
proportional
step
proportional
step
proportional
proportional
8 20
0-31
32-63
64-95
96-127
128-143
144-159
160-191
192-223
224-255
Shutter/ Strobe
–
all zones
Shutter closed
Shutter open
Strobe-effect from slow to fast
Shutter open
Opening pulses in sequences slow--> fast
Closing pulses in sequences fast --> slow
Shutter open
Random strobe-effects from slow to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
9 21
0 - 255
Dimmer
coarse
–
all zones
Dimmer intensity from 0% to 100%
proportional
10 22
0 - 255
Dimmer fine
-
all zones
Dimmer intensity from min.—>max.
proportional
*Default mode
**Halogen lamp effect during dimming
Zones:

Divine 160 RGBW
12
5. Control menu
The Divine 160 RGBW is equipped with a 4-segment LED display which allows you to set the fixture´s behaviour
according to your needs, obtain information on its operation, control all range of effects and program it
in stand-alone mode.
The four control buttons have the following functions:
- ESCAPE button-leaves menu without saving changes.
- ENTER button- enters menu, confirms adjusted values and leaves menu.
- UP and - DOWN buttons - move between menu items on the same level, sets values.
After switching the fixture on, display shows current DMX address.
5.1 Fixture Address
Use this menu to set the DMX address of the fixture.
dM.Ad. --- DMX addressing. Select this submenu to set a DMX start address.
To set a DMX address.
1. Use UP/DOWN buttons to find “ A001“ menu.
2. Press the ENTER button.
3. Use the UP/DOWN buttons to select desired start address.
4. Press the ENTER button to confirm the choice.
Note: After switching on, the Divine 160 RGBW will automatically detect whether DMX 512 data is received or not.
If there is no data received at the DMX input, the display will start to flash the set address.
DM.Pr. --- DMX preset. Select this menu item to set a desired DMX mode.
5.2 Fixture information
Use this menu to read useful information about the fixture status.
To display desired information.
1. Use the UP/DOWN buttons to find the “ InFo“ menu.
2. Press the ENTER button.
3. Use the UP/DOWN buttons to select the required menu item.
4. Press the ENTER button to confirm the choice.
Po.ti. --- Power On Time. Use the menu item to read the number of operation hours of the fixture.
totL - the function shows the total number of the operation hours since the Divine 160 RGBW has been
fabricated.
rESEt - the function shows the number of the operation hours since the counter was last reset.
In order to reset this counter to 0, you have to press and hold the UP and DOWN buttons and at the same
time press the ENTER button.

Divine 160 RGBW
13
VErS. ---Software Versions. Select this function to read the software version of the fixture processors.
ICI.b. --- display processor 1
IC2.b. --- display processor 2
IC3.L. --- LED processor 3
IC4.L. --- LED processor 4
ViFi --- Wireless DMX module (if installed)
tEMP --- Fixture Temperatures. Select this menu to read the temperatures of the fixture:
bASE
Cur.t. --- the current temperature of the fixture base.
Hi.tE. --- the menu item shows the max. temperatures of the fixture base since
the fixture has been fabricated.
rSEt --- the menu item shows the maximum temperatures of the fixture base since the counter
was last reset. In order to reset this counter to 0 you have to press and hold the UP and DOWN
buttons and at the same time press the ENTER button.
LEdS
Cur.t. --- the current temperature of the fixture LEDs PCB.
Hi.tE. --- the menu item shows the max. temperatures of the LEDs PCB base since
the fixture has been fabricated.
rSEt --- the menu item shows the maximum temperatures of the LEDs PCB since the counter
was last reset. In order to reset this counter to 0 you have to press and hold the UP and DOWN
buttons and at the same time press the ENTER button.
The temperatures can be displayed in either °C or °F units - see option “tnP.u.“ in the menu “Pers“.
DM.In.---DMX values. Select this function to read DMX values of each channel received by the fixture.
5.3 Personality
Use this menu to modify the Divine 160 RGBW operating behaviour.
DM.Pr. --- DMX preset. Select this menu item to set a desired DMX mode. Please refer to the chapter "DMX
protocol" for detail description of each DMX mode.
dM.In. --- DMX input. Select this menu item to select desired DMX input:
UirE --- Wired DMX.
UirL --- Wireless DMX
UrLo --- Wireless DMX –> wired DMX. The fixture receives wireless DMX signal and sends it to
its DMX output connector. Next fixtures can be connected to this fixture by DMX cable
(fixture works as a Wireless-DMX converter).
AnL.d. --- Analog dimmer. If this option is selected, the dimmer channel can be controlled via
DC voltage (0-10V) connected between pins 1 (data ground) and 3 (Data +) of DMX input of
the fixture (0-data ground, 10V-data +).
Procedure of setting:
1. Set fixture´s channels at desired values (by means of menu item Init Positions “In.Po”).

Divine 160 RGBW
14
2. Disconnect DMX controller
3. Select option “AnL.d.” from menu DMX input
4. Connect DC voltage to the DMX input of the fixture
F.tin. --- Max. Fade time. Select this menu item to set a desired max. fade time (0-25.4 sec.). This adjusted fade
time influences fade of Red, Green, Blue,White and dimmer during DMX operation:
If time between two receiving DMX values is > than fade time set in the item “F.tin. “, the entire adjusted fade time
will be used.
If time between two receiving DMX values is < than fade time set in the item“F.tin.“, the adjusted fade time will be
reduced to fill entire time between the two receiving DMX values.
e.g “F.tin.“=2sec. and fixture has received from DMX controller value Red=0 DMX, after 5 seconds will receive
Red=255 DMX. It means, that red will go to full intensity during 2 seconds.
“F.tin. “=8 sec. and fixture has received Red=0 DMX, after 5 seconds will receive Red=255 DMX. It means, that red
will go to full intensity during 5 seconds. (Max. fade time is reduced from 8 sec. to 5 sec.).
DiSP. --- Display adjusting. This function allows you to change the display settings.
d.On --- this function allows you to keep the display on or to turn off automatically 2 minutes
after pressing any button on the control panel.
d.Int. --- select this function to adjust the display intensity (6-min.,100-max.).
turn --- select this function to rotate menu 180 degrees from current orientation.
C.CL.n. --- Colour calibration. If the functin is on, the white output (R+G+B+W=full, Whites 2700K,3200K, 4200K,
5600K and 8000K) from the fixture is more uniform.
C.MI.n. --- Colour mixing mode. This menu item allows to select desired colour mixing mode:
rGBU --- RGBW mode
CMY --- CMY mode (the white channel is not active in this mode)
diM.C. --- Dimmer curve. The menu item allows to select desired dimmer curve:
Lin. --- linear
SqL --- Square law
UhI.C. --- White counting. If this function is on, the white channel uses red, green and blue chanels in proportional
relation to ensure max. light output in a white colour ( if white channel =full, also red, green and blue channels are
full).
tnP.u. --- Temperature unit. Use this menu in order to display the fixture temperatures in desired units: °C or °F.
In.Po. --- Init effect positions. Use this function to set all effects to the desired positions to which they will move
after switching the fixture on (if DMX is not receiving).
dF.SE. --- Default Settings .The menu item sets all fixture parameters to the default (factory) values.

Divine 160 RGBW
15
5.4 Manual mode
Use this menu to control all channels via buttons of the control board.
Items in this menu depend on selected DMX mode.
To control fixture channels.
1. Use the UP/DOWN buttons to find “ Man.C“ menu.
2. Press the ENTER button.
3. Use the UP/DOWN buttons to select desired effect (channel).
List of control channels:
“Func” – a channel Special Functions
“rEd.1” – a red LEDs saturation coarse- zone 1
“GrE.1” – a green LEDs saturation coarse- zone 1
“bLU.1” – a blue LEDs saturation coarse- zone 1
“VhI.1” – a white LEDs saturation coarse- zone 1
“rEd.2” – a red LEDs saturation coarse- zone 2
“GrE.2” – a green LEDs saturation coarse- zone 2
“bLU.2” – a blue LEDs saturation coarse- zone 2
“VhI.2” – a white LEDs saturation coarse- zone 2
“rEd.3” – a red LEDs saturation coarse- zone 3
“GrE.3” – a green LEDs saturation coarse- zone 3
“bLU.3” – a blue LEDs saturation coarse- zone 3
“VhI.3” – a white LEDs saturation coarse- zone 3
“rEd.4” – a red LEDs saturation coarse- zone 4
“GrE.4” – a green LEDs saturation coarse- zone 4
“bLU.4” – a blue LEDs saturation coarse- zone 4
“VhI.4” – a white LEDs saturation coarse- zone 4
“Cto” – a colour temperature correction
“Vir.C.” – a virtual colour wheel
“Stro.“ - a strobe/shutter
“dinr“ - a coarse dimmer
“din.F” a fine dimmer
4. Press the ENTER button and use the UP/DOWN buttons to set value , press the ENTER button to confirm it.
5. 5 Test sequences
Use this menu to run demo-test sequences without an external controller, which will show you some possibilities
of using the Divine 160 RGBW.

Divine 160 RGBW
16
5.6 Stand-alone setting
The fixtures on a data link are not connected to the controller but can execute pre-set programs which can be
different for every fixture. “Stand-alone operation” can be applied to the single fixture or to multiple fixtures
operating synchronously.
Auto. --- Automatic playback. This function allows you to select the program which will be played after switching
the fixture on. Selected program will be played continuously in a loop.
1. Use the UP/DOWN buttons to select test program (“tESt”), user program (“u.PrG”) or disable this function
(OFF).
2. Press the ENTER button to confirm the choice.
PLAY --- Playing program. Entering this menu provides a complete overview of all programs offered, from which
the selected program can run.
1. Use the UP/DOWN buttons to select desired program.
2. Press the ENTER button. The selected program runs in a loop.
Edit --- Editing a program. The fixture offers a freely editable program up to 40 steps. Every program step includes
a step time-the total time occupied by the step in the program and a fade time- during which effects move to new
positions.
1. Use the UP/DOWN buttons to select a desired program step ("St.01" - "St.40") and press ENTER button.
2. Use the UP/DOWN buttons to select a channel you want to edit and press the ENTER button.
List of editable items:
“P.End” - a total number of the program steps (value 1-40). This value should be set before start of
programming (e.g. if you want to create a program with 10 steps, set P.End=10).
“Func” – a channel Special Functions
“rEd.1” – a red LEDs saturation coarse- zone 1
“GrE.1” – a green LEDs saturation coarse- zone 1
“bLU.1” – a blue LEDs saturation coarse- zone 1
“VhI.1” – a white LEDs saturation coarse- zone 1
“rEd.2” – a red LEDs saturation coarse- zone 2
“GrE.2” – a green LEDs saturation coarse- zone 2
“bLU.2” – a blue LEDs saturation coarse- zone 2
“VhI.2” – a white LEDs saturation coarse- zone 2
“rEd.3” – a red LEDs saturation coarse- zone 3
“GrE.3” – a green LEDs saturation coarse- zone 3
“bLU.3” – a blue LEDs saturation coarse- zone 3
“VhI.3” – a white LEDs saturation coarse- zone 3
“rEd.4” – a red LEDs saturation coarse- zone 4
“GrE.4” – a green LEDs saturation coarse- zone 4
“bLU.4” – a blue LEDs saturation coarse- zone 4
“VhI.4” – a white LEDs saturation coarse- zone 4
“Cto” – a colour temperature correction
“Vir.C.” – a virtual colour wheel
“Stro.“ - a strobe/shutter
“dinr“ - a coarse dimmer
“din.F” a fine dimmer

Divine 160 RGBW
17
“F.tin” a fade time
“S.tin” a step time
“COPY“ – this item duplicates the current prog. step to the next prog. step.
Note: Items in this menu depend on selected DMX mode.
3. Use the UP/DOWN buttons to set a DMX value of the channel and then press the ENTER button.
4. Use the UP/DOWN buttons to select next channel and press the ENTER button.
5. After having set all channels in the current program step, press the ESCAPE button to go one menu level
back and select another program step.
5.7 Special functions
rdM.L --- Code.This menu item shows the first part of the RDM identification code.
rdM.H --- Code. This menu item shows the second part of the RDM identification code.
ViFi --- Wireless DMX. The menu serves for reading of the wireless operation status (only for Wireless DMX
version).
50 --- Wireless DMX signal intensity. The menu item shows level of received signal in %. If the fixture is not
linked to the transmitter, “niSS” is displayed.
UnLI --- Wireless DMX unlink. The item serves for unlinking the fixture from transmitter.
AdJ --- Effect Adjustment. The menu allows calibration of white colours.
dMH --- DMX Values. The menu item allows to set desired colour before calibrating of white colours.
C.CAL ---Colour calibration. Calibration of white colours.
LOA.C. – Loading a default (factory) calibration.
uPd.M. --- Updating mode. The menu item allows you to update software in the fixture via either serial or USB port
of PC.
The following are required in order to update software:
- PC running Windows 7/8/10 or Linux
- DMX Software Uploader
- Flash cable RS232/DMX P/N.13050624 (if you want to use serial port of PC)
- Robe Universal Interface (if you want to use USB port of PC)
Note: Software update should be executed by a qualified person. If you lack qualification, do not attempt the
update yourself and ask for help from your Anolis distributor.
DMX address, user program and all items in the menu "PerS" will be set to their default (factory) values.
To update software in the fixture:
I. Installation of the DMX Software Uploader.
1. DMX Software Uploader program is available from the Anolis web site at WWW.anolis.cz.
2. Make a new directory ( e.g. Anolis Uploader) on your hard disk and download the software to it.
3. Unpack the program to the directory.
II. Fixture software updating.
1.Determine which of your ports is available on your PC and connect it:

Divine 160 RGBW
18
- with the DMX input of the fixture if you are using the flash cable RS232/DMX
- with the DMX output of the Robe Universal Interface if you are using the USB cable.
Disconnect the fixture from the other fixtures in the DMX chain. Turn both the computer and
the fixture on. Make sure the lamp is switched off (only if the fixture involves a lamp).
2. Switch the fixture to the updating mode by selecting the "uPd.M." item and then selecting “yES“.
Note: If you do not want to continue in software update, you have to switch the fixture off and on
to escape from this menu.
We recommend canceling all running programs before starting the Software Uploader.
3. Run the Software Uploader program. Select desired COM and then click on the Connect button.
(Select COM if the serial port is used or Robe Universal Interface if the USB port is used).
If the connection is OK, click on the “Start Uploading button“ to start uploading. It will take several
minutes to perform software update.
If the option "Incremental Update" is not checked, all processors will be updated (including
processors with the same software version).
If you wish to update only later versions of processors, check the “Incremental Update box“.
Avoid interrupting the process. Update status is being displayed in the Info Box window.
When the update is finished, the line with the text “The fixture is successfully updated“ will appear in
this window and the fixture will reset with the new software.
Note: In case upload process is interrupted (e.g. power loss), the fixture stays in “Updating mode” and you will
have to repeat the software update again.

Divine 160 RGBW
19
6. Technical specifications
Power supply
• Electronic auto-ranging
• Input voltage: 100 - 277V AC, 50-60 Hz
• Max. power consumption: 440W
• Inrush current: 20A (at 230V), 30A (at 115V)
Optic & Effects
• Light source: 40 x RGBW multi-chip LED
• Beam angle: 15°,23°, 40°
• 4 LED zones
• RGBW colour mixing
• Built-in colour macros
• Adjustable strobe sequences
•Typical Lumen maintenance: 70% @ 60, 000 hours
Control
• Setting & Addressing: 4-segment LED display & 4 control buttons
• Control: USITT DMX 512 (RDM support)
• DMX protocol modes: 2 (10,22 control channels)
• Operations modes: DMX, Stand-alone
• Manual control of all effects via control panel
• One editable program, up to 40 steps
Wireless DMX/RDM module (only for wireless DMX version of the Divine 160 RGBW)
• Compliance with USITT DMX-512 (1986 & 1990) and 512-A
• Full DMX fidelity and frame integrity
• Auto sensing of DMX frame rate and frame size
• <5ms DMX latency
• Operational frequency range of 2402-2480 MHz
• Producer: LumenRadio
Strobe
• Strobe effect with variable speed (max. 20 flashes per second)
• Pre-programmed random strobe pulse-effects
Dimmer
• Smooth 16-bit dimming from 0 - 100 %
Connection
• ABB terminal blocks,type: DS 2,5/10.4L (4 springs mini blocks)
• Recommended data/power cable: Flamar Li9YC11Y cable 3xAWG16+1x(2xAVG24 shielded and jacketed)
UL Style 20233 O.D. 8.4mm
Mounting
• Via surface mounting adapter
Protection factor
• EU: IP 67
• US: Suitable for wet location

Divine 160 RGBW
20
Impact rating
• IK10
Temperatures
• Ambient operating temperature range: -20°C/+40° C
• Operating temperature: 75° C (at 40°C)
Minimum distances
Min. distance from flammable material: 0.3 m
Min. distance of illuminated object: 0.8 m
Total heat dissipation
• 1500 BTU/h (calculated)
Weight
• 14.5 kg
Dimensions
mm [inch]