Clarion CJ-5600E Repair manual

Clarion Co., Ltd.
All Rights Reserved. Copyright 2007: Clarion Co., Ltd.
Printed in Korea / Gedruckt in Korea / Stampato in Corea /
Imprimé en Corée / Impreso en Corea CJ-5600E
2007/2

2
English
1. Before Use................................................... 3
2. Features ...................................................... 3
3. Names of the Buttons .................................. 4
4. Operations ................................................... 4
5. Connections................................................. 7
6. Installation ................................................... 8
7. Troubleshooting........................................... 9
8. Specifications .............................................. 9
Contents
This unit has been tested and found to
comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This unit generates, uses, and can
radiate radio frequency energy, and, if not
installed and used in accordance with the
instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation.
If this unit does cause harmful
interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to consult the dealer or an
experienced radio/TV technician for help.
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS
PRODUCT NOT APPROVED BY THE
MANUFACTURER WILL VOID THE
WARRANTY AND WILL VIOLATE FCC
APPROVAL.
CJ-5600E.book Page 2 Friday, February 23, 2007 11:53 AM

3
English
Warning
•Do Not Back Up Vehicle While Relying Only on the Monitor Image
•Use Slow Speeds When Backing Up
•The rear-view monitor image has the same right-left inversion as your vehicle’s
rearview mirrors. Depending on the vehicle, the field and angle of view may differ.
Precautions (when you use the monitor)
zDo not touch the LCD panel.
zUse the product at the temperature range of -10°C ~ 60°C.
zScreen may be a little dark when the product is operated in low temperature areas.
Screen will show normal luminosity after a few minutes.
zDo not disassemble and modify the product in any way.
This may cause fire and/or electric shock.
zWhen you install the product in a car and watch monitor, the car engine should be
running as there might occur excessive discharge of the car battery.
zAny liquid leaking into product may cause malfunction.
Precautions (when you use the product in a car)
zThe driver should not use the product while he/she is driving.
zBe cautious of humidity and shock when you use the product in a car.
zCover the product when exposed to direct rays of the sun for a long period of
time.
(You should keep the product at a temperature range of -20°C ~ 70°C.)
zApplication of 5.6" TFT LCD with high resolution and low reflection
zAll functions are displayed on screen (OSD function)
z7 Language Display Selection
(ENGLISH-DEUTSCH-ITALIANO-FRANÇAIS-ESPAñON- - )
zFree voltage (From DC12V to DC24V)
zDimmer selection function
zPicture quality control (PWM control)
zCamera input (2 system)/Work together with back gear/turn signal
1. Before Use
2. Features
CJ-5600E.book 3 ページ ２００７年２月７日 水曜日 午前９時２５分

4
English
POWER
MODE (Camera Selection)
It is a function to change CAMERA (CAM1/CAM2).
3. Names of the Buttons
4. Operations
[POWER]
[MODE]
[MENU]
[UP]
[DOWN]
STAND BY LED
1
ON OFF (1) Press [POWER] button to on the power.
(STAND BY state is OFF)
(2) Press [POWER] button again to off the
power.
(STAND BY state is ON)
2
CAM1 CAM2
(1) Press [MODE] button.
(2) CAM1 or CAM2 appears on the screen
and it disappears after 5 seconds.
CAM1
Note: In the mirror mode, the character is
inverted.
CJ-5600E.book 4 ページ ２００７年２月７日 水曜日 午前９時２５分

5
English
MENU
It is a function to select MAIN MENU (SETUP, PICTURE CAMERA)
(1) Press [MENU] button to select MAIN MENU, changed color in red when it is selected.
• Every time the button is pressed, the setting changes.
(2) Press [MODE] button to select SUB MENU, changed color in red when it is selected.
• Every time the button is pressed, the setting changes.
SET UP (SUB MENU)
(3) Press [UP]/[DOWN] button to change Settings.
zDIMMER
–
zLANGUAGE
– – – – –
–
3
SETUP PICTURE CAMERA
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0
CONTRAST
BRIGHTNESS
COLOR
TINT
50
50
50
70
SUB MENU
CAM1
CAM2
NORMAL
NORMAL
zSETUP zPICTURE
zCAMERA
ENGLISH DEUTSCH ITALIANO FRANÇAIS ESPAñON
CJ-5600E.book 5 ページ ２００７年２月７日 水曜日 午前９時２５分

6
English
zDIRECTION (Inverted upside down)
zRESET X
A factory default reset will clear all of OSD information
PICTURE (SUB MENU)
(3) Press [UP]/[DOWN] button to change Settings.
CAMERA (SUB MENU)
(3) Press [UP]/[DOWN] button to change Settings.
zIn the mirror mode, the screen is inverted laterally.
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
0
DIMMER
LANGUAGE
DIRECTION
RESET
ENGLISH
180
CONTRAST
BRIGHTNESS
COLOR
TINT
70
40
40
40
CONTRAST
BRIGHTNESS
COLOR
TINT
40
40
70
40
CONTRAST
BRIGHTNESS
COLOR
TINT
40
70
40
40
zCONTRAST zBRIGHTNESS zCOLOR
CONTRAST
BRIGHTNESS
COLOR
TINT
40
40
40
50
zTINT
CAM1
CAM2 NORMAL
NORMAL
CJ-5600E.book 6 ページ ２００７年２月７日 水曜日 午前９時２５分

7
English
5. Connections
*3 *3
*2
*2
*1
*1
GREEN
(CAMERA2)
BLACK
(CAMERA1)
BLACK
GROUND
RED
POWER
DC12V~24V
CAMERA2 CAMERA1
CAMERA1
(Sold Separately)
CAMERA2
(Sold Separately)
*1 Use a Clarion camera.
*2 A relay cable, sold separately, is required
for connecting the camera.
*3 Use tape to keep the connection between
the monitor cable and the camera relay
cable secure.
BLACK (CAMERA-1, priority) Standby + (for rear-view)
Connect this cable to “+” of back gear lamp.
GREEN (CAMERA-2) Standby + (for side-view)
Connect this cable to “+” of turn signal lamp.
CJ-5600E.book 7 ページ ２００７年２月７日 水曜日 午前９時２５分

8
English
1. Choose a location where you install the Monitor. Clean the place for the Stand with cleanser
and remove the Protective Tape. And then attach it exactly where you want.
2. Fasten the Monitor with Tapping Screw.
3. Adjust angle of Stand and install Monitor.
4. Connect each connecting cable as in the product installation reference.
Monitor Cable Connection
6. Installation
Cable Guidance
Fix Knob
(Bracket)
Tapping Screw
Safeguard tape
Control Knob
(Angle)
Stand Base
* Installed on the ceiling * Normal Installation
CJ-5600E.book 8 ページ ２００７年２月７日 水曜日 午前９時２５分

9
English
Caution: The design and specifications of this product in order to improve its quality may be changed without notice.
7. Troubleshooting
Problem Cause Measure
No image is displayed. Is camera connected
properly?
Check the wiring to the camera and the
camera connection.
Power does not turn on.
Is power cable
connected properly? Check the wiring.
Is a fuse blown out? Replace with a fuse of the same amperage
(2A).
Color is washed-out.
Operating
environment is
inappropriate.
Temperature in the car is below 0°C or over
60°C. Check to see that the temperature in
the car is appropriate (around 25°C).
8. Specifications
ITEM SPECIFICATION
NTSC PAL
PANEL
SCREEN SIZE 5.6 INCH (14.22cm)
NUMBER OF PIXELS 320(W) x 3(RGB) x 234(H)
DOT PITCH 0.118(W) x 0.362(H) mm
BRIGHTNESS 350 cd/m2
DISPLAY AREA 113.28(W) x 84.7(H) mm
CONTRAST RATIO 300:1
VIEW ANGLE (H/U/D) 65deg / 45deg / 65deg
POWER SUPPLY VOLTAGE DC 12V - 24V
CURRENT 550mA (DC 12V, MONITOR SET ONLY)
REAR INPUT POWER DC 12V - 24V
INPUT SYSTEM AUTO (NTSC/PAL)
FREQUENCY HORIZONTAL 15.734 KHz 15.625 KHz
VERTICAL 60Hz 50Hz
OSD DISPLAY 7 LANGUAGE
USER CONTROLS POWER, MODE, MENU, UP, DOWN
OPERATING TEMPERATURE -10°C ~ + 60°C
STORAGE TEMPERATURE -20°C ~ + 70°C
DIMENSION (W x H x D) 163(W) x 112(H) x 30(D)
WEIGHT 0.3Kg
ACCESSORIES MONITOR CABLE ASS’Y·····································1
STAND ASS’Y·······················································1
CJ-5600E.book 9 ページ ２００７年２月７日 水曜日 午前９時２５分

Clarion Co., Ltd.
All Rights Reserved. Copyright 2007: Clarion Co., Ltd.
Printed in Korea / Gedruckt in Korea / Stampato in Corea /
Imprimé en Corée / Impreso en Corea CJ-5600E
2007/2