
WOOFER FEATURES TWEETER FEATURES CROSSOVER FEATURES
• UV protected Injection-
molded polypropylene cone
bodies with santoprene
rubber surrounds, specifically
formulated
for
marine
duty
• High-e
ff
iciency design with
neodym
ium motor system • Natural woofer roll-off with 2nd
order high-pass filter on tweeter
• Marine-grade, synthetic spider
• Wide mounting flange
design maximizes retrofit
compatibility with standard
6.5-inch marine speakers
• 1-inch (25 mm) silk
dome
diaphr
agm
with specially
formulated treatment
to
withstand UV
and
salt-
spray exposure
• Crossovers are integrated into
woofer basket, requiring
no
additional mounting provision
BUILT-IN RGB LIGHTING
• Ferrofluid-cooled and damped
for improved response • Multi-color LEDs, embedded
and concealed from direct sight,
produce lively
acce
nt lighting
and
power handling
• Meets salt-fog and UV exposure
standards
(AS
TM B117/D4329) • Permanent, basket-mounted
design ensures optimal high-
frequency performance with no
loss
of woofer radiating area
Included
Components
and Parts:
• Two Marine Coaxial Loudspeakers
• Two White Sport SpeakerGrilles
• Two Gunmetal SportSpeaker Grilles
• Two 2nd Order High-Pass
Fi
lters
(integrated within woofer baskets)
• Twelve M4 x
30
mm
Stainless-Steel Mounting Screws
• Two Waterproof Connection Harnesses
• Mounting Template
• Owner's Manual
RGB
LED
Illumination:
LED functiona
li
ty
requires separate wiring
at
each
speaker location. Choose from seven fixed LED colors
or
connect an RGB lighting controller (sold separately)
for adjustable control.
BEFORE
YOU
BEGIN INSTALLING
•
Check
with your local waterway authority
for
any regulations regarding t
he
use of
accer:it/speaker lighting on your vessel.
• Turn
off
the audio system. It is also
advisable
to
disconnect your battery system
whenever performing installation
work
.
• Before c
ut
ting, drilling
or
inserting any screw,
check
clearances on
bo
th sides
of
the planned
mounting surface. Al
so
check
for
any potential
obstacles,
such
as wiring harnesses, fuel
lines, hydraulic lines,
etc
. Check
both
sides
of
the
vessel before cutting any holes.
• If you are running cables through bulkheads,
drill holes for the
cab
le and use a urethane
or
plastic grommet
to
protect the wire from
chafing in
the
hole. Make sure
that
the
cables will clear any mechanical devices in
the
boat
and
secure them with wire ties.
• Wear protective eyewear at all times
and
a dust
mask and gloves when drilling
or
cutting.
fflCAUTIONI
When installing speakers in your vessel,
it
is
extremely important
to
secure them firmly. This
applies
not
only
to
the
speakers themselves,
but
also any structure they are mounted
to
. If
not
firmly
attached,
the
speakers can
become
dangerous
projectiles in a collision. Please review
the
mounting information carefully and use the supplied
marine-grade hardware
to
mount this product.
fflWARNINGI
While
these
speakers
are
designed to
be
water
and
spray
resistant,
they
are
not designed tobe submerged or to
withstand
high-pressure
water
spray.
Do not
install
on
submersibles,
personal
watercraft or
any
other
vessel
likely
to
be
under water at
any
time.
Please
exercise
care
when
washing
your boatto
avoid
damaging your
speaker.
Avoid
contact with
harsh
chemicals
or
cleaning
agents
toprevent
damage
to the
speaker's
finish thatwill not
be
covered
under
warranty.
Wash
with mild
soap
and
rinse
with
freshwater
only.
fflCAUTION
I
Prolonged exposure
to
sound pressure levels in
excess
of
100dB
can cause permanent hearing
loss. This high-performance speaker can exceed
this level. Please exercise restraint in its operation
in
order
to
preserve your ability
to
enjoy its fidelity.
fflWARNINGI
It
is
absolutely vital that your coaxial speaker
system is connected as shown in this manual.
Failure
to
connect the system as shown will
result in damage
to
your speakers which
is NOT covered underwarranty.
Do
not
substitute different crossover networks.