Clark Synthesis TST429 User manual
2
3
4
6
8
9
10
12
14
18
19
Transducer
Installation Guide
Visit our website for
more information!
Tactile Sound Transducers
2www.clarksynthesis.com
!
IMPORTANT PRODUCT INFORMATION
CAUTION:
3
www.clarksynthesis.com Tactile Sound Transducers
Introduction
Before you drill holes and run wires, take a few moments to review this Installation Guide. Then plan
out the steps you’ll need to take for your particular application. This will save you time in the end and
reduce the possibility of errors and/or damage to the Transducer.
Tactile Sound Transducers
4www.clarksynthesis.com
Supplied Parts
SUPPLIED PARTS (ILLUSTRATED BELOW)
A
IK
5
www.clarksynthesis.com Tactile Sound Transducers
Wood is one of the best conductors of tactile vibrations. In most
applications, the Transducer should be centrally located on the structure
(chair, floor, riser, deck, etc.) in order to evenly distribute the tactile effect.
When two or more Transducers are used on one structure, they should
be spaced equidistant from each other and the edges/boundaries of the
structure. Mounting to a bridge, joist, or frame member is preferred.
General Location Diagram
General Information
Tactile Sound Transducers
6www.clarksynthesis.com
Installation Type: Unimount Bracket
Installation: Overview
Tip: Tighten
two jam nuts
against each
other to screw in
hanger bolt using
wrench.
Installation Type: Hanger Bolt
NEVER TIGHTEN
BY TURNING THE
Transducer. MAKE
SURE TO TIGHTEN
THE JAM NUT
AGAINST THE
Transducer’S BRASS
NUT
7
www.clarksynthesis.com Tactile Sound Transducers
Installation: Overview
Installation Type: T-Nut Installation Type: Hex Bolt
NEVER TIGHTEN
BY TURNING THE
Transducer. MAKE
SURE TO TIGHTEN
THE JAM NUT
AGAINST THE
Transducer’S BRASS
NUT
Tactile Sound Transducers
8www.clarksynthesis.com
Installation: Chairs & Couches
Hardwood Bridge (min. 3/4” thick)
9
www.clarksynthesis.com Tactile Sound Transducers
Installation: Floors, Platforms & Staging
Tactile Sound Transducers
10 www.clarksynthesis.com
INSTALLATION USING THE T-NUT
DO NOT OVERTIGHTEN THE Transducer!
Installation: Laminated I-Beam Floors
INSTALLATION USING THE UNIMOUNT BRACKET
DO NOT OVERTIGHTEN THE Transducer!
NEVER TIGHTEN BY TURNING THE Transducer – MAKE SURE TO TIGHTEN THE JAM NUT AGAINST THE
Transducer’S BRASS NUT.
MOUNTING DETAIL
11
www.clarksynthesis.com Tactile Sound Transducers
Notes
Tactile Sound Transducers
12 www.clarksynthesis.com
2
1
Bridge Mount
Jam Nut
Installation: Wood Decks
Joist Mount
13
www.clarksynthesis.com Tactile Sound Transducers
3
CAUTION: DO NOT OVERTIGHTEN.
CAUTION: DO NOT TIGHTEN THE JAM NUT TO THE BRASS NUT BY TURNING THE TRANSDUCER.
THIS WILL RESULT IN SEVERE DAMAGE TO THE TRANSDUCER AND WILL VOID THE WARRANTY.
4
5
Installation: Wood Decks
Tactile Sound Transducers
14 www.clarksynthesis.com
Amplifiers and Wiring
AMPLIFIER SPECIFICATIONS
HOME THEATER
LFE/SUB HOOKUP
L
R
LFE/SUB
IN
Y Adapter
To Input of
Powered
Subwoofer
Y Adapter
Subwoofer
Transducer
Home Theater Receiver
Amplier
Output
–+
15
www.clarksynthesis.com Tactile Sound Transducers
Right Front (RF) and Left Front (LF) Hookup
NOTE:
Multiple Signal Hookup
L
L
R
R
OUTPUT
LF
Pre-Amp Audio Out
RF
IN
IN
Y Adapter
Transducer
Transducer
Home Theater Receiver
Home Theater Receiver
Mixer
Output
Output
–
–
+
+
LF CENTER LFE/SUB
CH4CH3CH2CH1
Pre-Amp Audio Out
RF
Amplier
Amplier
Amplifiers and Wiring
Tactile Sound Transducers
16 www.clarksynthesis.com
Input Audio Input Signal
Amplier
Output
–+
–+
R L
L
R
IN
Transducer
Amplier
Output
–+
Audio Input Signal
Transducer
Amplifiers and Wiring
Transducer Transducer
Two Transducers with a Stereo Amplier
Two Transducers with a Mono Amplier (or with a Single Amplier Channel)
17
www.clarksynthesis.com Tactile Sound Transducers
Wiring Diagrams & Videos
Wiring Diagram Wiring Video
Wiring Diagram Wiring Video
Wiring Diagram Wiring Video
Wiring Diagram Wiring Video
TST239 Silver Transducer
TST329 Gold Transducer
TST429 Platinum Transducer
AW339 & AW439 All-Weather Transducers
Tactile Sound Transducers
18 www.clarksynthesis.com
Symptom Troubleshooting Question Remedy
Troubleshooting
19
www.clarksynthesis.com Tactile Sound Transducers
United States Warranty and Return Policy
TST239, TST329, TST429, AW339, AW439 Transducer WARRANTY
two years
six months.
ve years two years.
WHAT IS NOT COVERED
RETURN POLICY
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE
International Warranty and Return Policy
Warranty & Returns
Other manuals for TST429
3
This manual suits for next models
4
Table of contents
Other Clark Synthesis Transducer manuals
Clark Synthesis
Clark Synthesis TST239 User manual
Clark Synthesis
Clark Synthesis TACTILE SOUND AW339 User manual
Clark Synthesis
Clark Synthesis Prosound429 User manual
Clark Synthesis
Clark Synthesis TST429 User manual
Clark Synthesis
Clark Synthesis TST429 User manual
Clark Synthesis
Clark Synthesis TST209 User manual
Clark Synthesis
Clark Synthesis TST329 User manual
Clark Synthesis
Clark Synthesis TST329 User manual
Clark Synthesis
Clark Synthesis TACTILE SOUND AW339 User manual
Clark Synthesis
Clark Synthesis TACTILE SOUND AW339 User manual
Popular Transducer manuals by other brands
aci
aci ACCESS series Installation & operation instructions
PCE Instruments
PCE Instruments PCE-P18 user manual
Comet
Comet T4311 instruction manual
Hontzsch
Hontzsch UVA-AS102 operating instructions
Airmar Technology Corporation
Airmar Technology Corporation R99 owner's guide
HBM
HBM C16A Series operating manual
Lumel
Lumel P30O user manual
M-system
M-system 18RP instruction manual
S+S Regeltechnik
S+S Regeltechnik THERMASGARD MWTM-I Operating Instructions, Mounting & Installation
Thyracont
Thyracont VSM72 operating instructions
Simrad
Simrad ES333-7CD - REV A installation manual
Thermo Scientific
Thermo Scientific STD5000 user guide
Simrad
Simrad 120-2X50 - REV A datasheet
Kistler
Kistler 9327C instruction manual
Airmar
Airmar Tilted Element B164 Owner's guide and installation instructions
S+S Regeltechnik
S+S Regeltechnik AERASGARD RCO2-W-A Operating Instructions, Mounting & Installation
Omega
Omega RH62 Series manual
Escort
Escort ECT-670 user manual