Clark Synthesis TACTILE SOUND AW339 User manual

www.clarksynthesis.com
11/2008 Ver. 1 ©2008 Clark Synthesis, Inc.
OEM Installation Guide
AW339 All-Weather Transducer-
Hot Tub/Spa Installation
For additional questions/concerns/issues, contact
Clark Synthesis or visit our web site.
Clark Synthesis, Inc.
8020 Southpark Circle, Suite 600
Littleton, CO 80120
Phone: [phone]
Fax: [phone]
Web: www.clarksynthesis.com
Email: [email protected]
CLARK SYNTHESI S
TACTILE SOUND
®
CLARK SYNTHESI S
TACTILE SOUND
®
CAUTION: THIS SPEAKER IS DESIGNED FOR OUTDOOR USE.
HOWEVER, THE SPEAKER IS NOT WATERPROOF AND SHOULD
NOT BE EXPOSED TO CONTINUOUS WATER FLOW OR BE
SUBMERGED IN ANY WAY.
!
CAUTION: STRONG MAGNETS ARE USED IN THIS PRODUCT.
AVOID CONTACT WITH, OR PLACEMENT NEAR, ITEMS THAT CAN
BE DAMAGED OR AFFECTED BY MAGNETIC FIELDS.
CAUTION: DO NOT TIGHTEN THE JAM NUT TO THE BRASS NUT
BY TURNING THE TRANSDUCER. THIS WILL RESULT IN SEVERE
DAMAGE TO THE TRANSDUCER AND WILL VOID THE WARRANTY.

www.clarksynthesis.com
AW339- HOT TUB OEM INSTALL
The AW339 mounting bracket is the component used to attach the
transducer to the hot tub or spa. The mounting bracket and related hardware
come in the transducer package.
The mounting bracket assembly includes the mounting bracket, a threaded
stud, and two jam nuts (see diagram below). The mounting bracket is
secured to the underside of the hot tub. The threaded stud attaches the
transducer to the mounting bracket. The jam nuts secure the threaded stud
to the mounting bracket and transducer.
When prototype testing the transducer with your hot tub, the mounting
bracket can be applied to the hot tub with epoxy. During this type of
application, do not allow the epoxy to expand into the hole where the
threaded stud is placed or you will not be able to insert the stud.
There are several factors to consider when selecting the mounting location
for the mounting bracket and transducer:
You need to insure the area allows for adequate clearance for the1.
transducer. The transducer should only touch the tub by way of the
mounting bracket. If the transducer comes in contact with other parts of
the hot tub it may affect the sound quality.
The location should allow for as much air space around the transducer2.
as possible. This will allow heat to escape from the transducer.
The location should be accessible. This will prove invaluable should the3.
transducer require service.
You may want to locate the transducer close to the location of the hot4.
tub’s amplier/sound unit to avoid additional wiring.
For larger tubs, you may want to consider mounting two transducers for5.
added performance.
Once prototype testing is complete and a nal location is determined,
the mounting bracket should be permanently fused with the tub during
production. This process involves covering the bracket with berglass.
Again, insure the threaded hole is protected during this process so no
material obstructs the threads/opening. The factory install is now complete.
Once the hot tub is installed by the dealer, the dealer can then install the
transducer. DO NOT SHIP WITH THE TRANSDUCERS ATTACHED. This
installation is done by placing the transducer’s brass mounting nut onto
the threaded stud. Insuring not to crossthread the brass nut, gently turn
the transducer 5 to 6 complete revolutions. If you feel resistance, stop
immediately. CAUTION: DO NOT OVERTIGHTEN. Spin the jam nut on the
stud down to the brass nut and, using two wrenches (one on the jam nut
and one on the brass nut), tighten the jam nut against the brass nut.
CAUTION: DO NOT TIGHTEN THE JAM NUT TO THE BRASS NUT
BY TURNING THE TRANSDUCER. THIS WILL RESULT IN SEVERE
DAMAGE TO THE TRANSDUCER AND WILL VOID THE WARRANTY.
You may now connect the wires to your amplier (must be a 4 ohm stable
amp delivering 125-150 watts @ 4 ohms/speaker). Your install is complete.
SIDE VIEW
Mounting Bracket
Threaded Stud
Jam Nuts
MOUNTING BRACKET ASSEMBLY
TOP VIEW
Transducer
CROSS-SECTION OF TUB
TRANSDUCER LOCATION
Possible Locations
for Transducer and
Mounting Bracket