Clarke CPE15S Instruction Manual

OPERATION & MAINTENANCE
INSTRUCTIONS
1002
MODEL NO: CPE15S/T-20S/T-30S/T
PART No: 7120203/4-7120205/6-7120207/8
CPE RANGE PUMPS
CPE RANGE PUMPS

-1-
Please note that the details and specifications contained herein are correct at the time of going to
print. However CLARKE International reserve the right to change specifications at any time without
prior notice. Always consult the machines data plate
Contents
Specifications .................................................................................. 2
Guarantee : .................................................................................... 3
Safety Precautions.......................................................................... 4
Water Connections ........................................................................ 5
Electrical Connection : .................................................................. 6
Maintenance : ................................................................................ 7
Trouble Shooting ............................................................................. 7
Parts (CPE15) : .........................................................................9 & 10
Parts (CPE20) : .......................................................................11 & 12
Parts (CPE30) : .......................................................................13 & 14
We delare that this product complies with the 73/23/EEC directive.

-2-
SIZE MOTOR MAX FLOW MAX WEIGHT PART
MODEL INCHES HP VOLTS/PH LPM HEAD M KG No
CPE15S 1½” 1 230/1 325 17 14.0 7120203
CPE15T 1½” 1 400/3 325 17 14.0 7120204
Specifications
CPE30S 3” 3 230/1 800 18 15.5 7120207
CPE30T 3” 3 400/3 800 18 15.5 7120208
CPE20S 2” 2 230/1 500 17 14.5 7120205
CPE20T 2” 2 400/3 500 17 14.5 7120206

-3-
CLARKE GUARANTEE
This CLARKE product is guaranteed against faulty manufacture for a period
of 12 months from the date of purchase. Please keep your receipt as proof
of purchase.
This guarantee is invalid if the product is found to have been abused or
tampered with in any way, or not used for the purpose for which it was
intended.
Faulty goods should be returned to their place of purchase, no product
can be returned to us without prior permission.
This guarantee does not affect your statutory rights.
Please read these instructions carefully before operating the Pump
Thank you for purchasing this CLARKE Pump
Before using the device, please read this manual thoroughly and carefully follow
all instructions given. This is for your own safety and that of others around you, and
is also to help you achieve long and trouble free service from your new tool.
Your CLARKE CPE PUMP is a highly efficient, robust, continuously rated, self priming pump
with a powerful electric motor, and is ideal for a wide range of domestic, commercial and
agricultural uses.
It is suitable for pumping clean tap and rain water , and will handle small solids in suspension.
Your CLARKE CPE PUMP is designed to give you trouble free service provided it is installed
and used in the correct way.
Please follow these instructions carefully.
WARNING
CPE RANGE PUMPS ARE NOT SUBMERSIBLE PUMPS.
ON NO ACCOUNT MUST THEY BE IMMERSED IN WATER.
if the pump is left in an exposed position, it should be protected from the elements. especially
frost.
All electrical connections should be inspected regularly for signs of corrosion and cleaned
where necessary. It is advisable to apply a film of silicon grease on the terminals for added
protection.

-4-
Safety Precautions
These pumps are designed to pump Water Only. NEVER use for pumping flammable
liquids or chemicals of any kind.
ALWAYS ensure the pump is installed in a horizontal position with the outlet facing
vertically upwards, and that it is firmly anchored via its fixing screws.
ALWAYS ensure there is an adequate air flow around the pump. DO NOT mount it
in an enclosed atmosphere.
ALWAYS ensure all water pipes - supply or discharge, are adequately supported
where necessary, so as not to put a strain on the pump connections.
ALWAYS ensure the inlet to the pump is completely unrestricted.
ALWAYS ensure the pump is protected from the elements, neither the motor nor the
electrical terminal box is intended to be waterproof.
ALWAYS ensure that all pipes are protected against damage where necessary,
and that they are suitably lagged to avoid the possibility of freezing during cold
weather.
ALWAYS disconnect the pump from the electrical supply before any cleaning or
maintenance of the pump.
NEVER allow the pump to run dry, as this will cause serious damage to the pump
seals.
NEVER switch the pump ON when a swimming pool etc, is in use, i.e., when there is
person or animal in the pool.
WARNING:
As with all machinery, there are certain hazards involved with their operation
and use. Exercising respect and caution will considerably lessen the risk of
personal injury. However, if normal safety precautions are overlooked or ignored,
personal injury to the operator even damage to the pump or property, may
result. For your own safety and that of others around you, please read these
safety instructions in conjunction with the operating instructions, and before using
the pump.

-5-
Water Connections
IMPORTANT: The pump MUST NOT be connected to the mains supply until all hose/pipe
installation is completed. DO NOT RUN THE PUMP DRY
NOTE: If any part of the system is to be connected to the mains water supply, ensure that
local water authority regulations are observed.
Because of the variety of possible installations, no plumbing accessories are supplied with
your pump, however accessories designed specifically for this range of pumps is available
from your nearest CLARKE dealer.
The pump must always be installed and
operated in an upright position i.e. with the
outlet port facing vertically upwards. The
fixing holes in the base should be used as
necessary to secure the pump firmly in it
operating position. Also ensure there is
adequate air circulation around the motor.
Avoid situations where there is a risk of water
coming into contact with the outside of the
pump. Neither the motor or the terminal box
are designed to be waterproof.
These notes are for guidance on how to achieve a proper working system. The diagram
(Fig. 1) above shows a typical installation at the pump.
A foot valve and filter should be fitted to the lower end of the suction hose, as illustrated in
Fig. 2, so as to retain water in the suction system and more importantly, to prevent the
possibility of large foreign objects entering the pump body.
The performance of your pump will be affected by the diameter of
the inlet pipe - any restriction will greatly reduce the flow. We strongly
recommend that you use a pipe diameter as large as practicable.
A gate valve may be installed in-line on the delivery side (Outlet Port)
of the pump which can be adjusted as required to regulate the flow
of water, it can also assist in priming the pump.
WARNING DO NOT place any such obstruction on the suction side
(inlet Port) of the pump unless it is an isolator valve in a gravity fed
system. It is also IMPORTANT to note, that these pumps should not be
operated with the delivery valve completely closed.
To prevent unnecessary strain or possible distortion to the pump, ensure
that adequate support is provided to the hoses and or pipes. They will
be considerably heavier when filled with water.
Filter
Foot
Valve
Fig. 1
Fig. 2
Should foreign contaminants come into contact with the pump, flush through with cold
water as soon as possible to prevent damage to the pump.
Protect the pump and pipework from freezing. The formation of ice may cause serious
damage.
Where the pump is to be a permanent fixture, the fittings to the pump MUST be flexible, i.e.
a short piece of hose should be inserted between the rigid pipework and the pump.

-6-
Electrical Connection
Wiring Connections For Three Phase Models
Again installation should be carried out by a qualified electrician, using I.E.E cable and
fittings, and in accordance with I.E.E Regulations. To connect the cable to the motor see
electrical connections inside the terminal cover.
Single phase pumps should be connected to a standard domestic 13 amp, 230 volt (50Hz),
electrical supply, we strongly recommend that the connection be made via a suitable
isolator switch and Residual Current Device (RCD).
IMPORTANT: Should the supply be taken from a normal 13 amp socket, then the plug used
must be to BS 1363 standard, and the wires should be wired up in accordance with the
following colour code:
Green & Yellow ............... Earth or marked with a letter “E” or Earth symbol “ ”.
Blue ................................... Neutral or terminal marked with a letter “N”
Brown ............................... Live or terminal marked with a letter “L”
Wiring Connections For Single Phase Models
Connections InsideTerminal Box
Delta Connection Star Connection
L1 L2 L3 L1 L2 L3
WARNING: THIS PUMP MUST BE EARTHED.
Before connecting the pump, check the voltage and phase supply required, this information
can be found on the junction box cover on top of the motor.
Installation should be carried out by a qualified electrician, using I.E.E approved cable and
fittings, and in accordance with I.E.E. Regulations. However, in the further interests of safety
we would emphasise the following,
IF IN ANY DOUBT, contact CLARKE International Service on 020 8988 7400

Maintenance
No regular maintenance is required other than regular inspection to ensure that leaves
and other particles are not covering the suction inlet, also check the pump for signs of wear
or damage.
If any signs of wear or damage are found, contact your nearest Clarke dealer.
If you suspect that your pump is blocked by mud, silt , leaves etc, disconnect from
the mains supply and backflush. This should dislodge any blockage and aid cleaning.
PARTS & SERVICE TEL: [phone]
or e-mail as follows:
PARTS: [email protected]
SERVICE: [email protected]
Trouble Shooting
The pump does not run 1. No mains supply 1. Check fuse - replace if
necessary (Check fuse rating).
2. Impeller seized / blocked 2. Disconnect pump from mains,
investigate cause and clear
blockage etc..
Pump runs but no output 1. Air in pump housing 1. Disconnect from the mains and
check all hose connections
are air tight etc.
2. Suction height too great 2. Check height is within spec. for
your pump, (see specs page 2).
Low or no Flow 1. Blocked inlet pipe 1. Check to see that no foreign
matter is fouling the intake
system and check the filter is
not blocked or obstructed.
2. Head too high 2. Check that head is within spec.
there is little likelihood of problems arising, but if water will not flow as it should then check
the following points:-
Should you still experience problems, then contact your Clarke dealer, or CLARKE
International Service Department for advice.
-7-

PARTS DIAGRAM (CPE15)
-9-

-10-
PARTS LIST (CPE15)
Index No Part No Description Qty
1GM1076 Connection 1½” x 40 1
2 GM5853 Valve Body 1
3 GM6010 Check Valve 1
4 GM6162 Washer 1
5 GM6186 Flexolite Washer 1
6 GM6209 Tap ¼” 1
7 GM6213 Tap 1” 1
8 GM6230 Screw 6
9 GM6268 Screw 8
10 GM6334 Mechanical Seal 1
11 GM7103 Nut 1
12 GM7702 Counterface 1
13 GM7776 Cover Disk 1
14 GM8048 ‘O’ Ring 1
15 GMF156 Key 4x4x16 1
16 GMF458 Pump Body 1
17 GMF501 Impeller 1
18 GM5114 Rear motor Cover 1
19 GM5119 Elastic Washer 1
20 GM5293 Fan 1
21 GM5319 Fan Cover 1
22 GM5375 Bearing 1
23 GM5387 Motor Stator For CPE 15 A1 (1HP) 1
24 GM5493 Motor Stator For CPE 15 A3 (3HP) 1
25 GM5513 Bearing 1
26 GM6581 Condenser 20 For CPE 15 A1 1
27 GM6764 Vis 4
28 GM6963 Condenser Box For CPE 15 A1 1
29 GM7259 junction Box Cover For CPE 15 A3 1
30 GM7700 Motor Bracket 1
31 GM8640 Motor Shaft For CPE 15 A1 1
32 GM8641 Motor Shaft For CPE 15 A3 1
33 GMF313 Motor (1PH) 1
34 GMF490 Motor (3PH) 1
Motor Pump

-11-
PARTS DIAGRAM (CPE20)

-12-
PARTS LIST (CPE20)
Index No Part No Description Qty
1GM1010 Connection 2” x 50 2
2 GM5342 Washer 1
3 GM5571 Pump Body 1
4 GM5854 Valve Body 1
5 GM6012 Check Valve 1
6 GM6029 Flexolite Gasket 1
7 GM6162 Washer 1
8 GM6186 Flexolite Washer 1
9 GM6209 Tap ¼” 1
10 GM6213 Tap 1” 1
11 GM6235 Screw 4
12 GM6236 Screw 6
13 GM6334 Mechanical Seal 1
14 GM6346 Counterface 1
15 GM7103 Nut 1
16 GM8612 Impeller 1
17 GMF156 Key 4x4x16 1
18 GM5465 Bearing 1
19 GM5466 Bearing 1
20 GM5503 Motor Bracket 1
21 GM6994 Condenser 30 For CPE 20 A1 1
22 GM6996 Elastic Washer 1
23 GM6997 Rear Motor Cover 1
24 GM6998 Fan 1
25 GM6999 Fan Cover 1
26 GM7168 Motor Stator For CPE 20 A1 (1HP) 1
27 GM7176 Motor Stator For CPE 20 A3 (3HP) 1
28 GM8002 Condenser Clip 1
29 GM8018 junction Box Cover 1
30 GM8084 Screw 4
31 GM8643 Motor Shaft For CPE 20 A1 1
32 GM8650 Motor Shaft For CPE 20 A3 1
33 GM8657 Motor (1PH) 1
34 GM8658 Motor (3PH) 1
Motor Pump

-13-
PARTS DIAGRAM (CPE30)

-14-
PARTS LIST (CPE30)
Index No Part No Description Qty
1 GM5342 Washer 1
2 GM5574 Pump Body 1
3 GM5857 Valve Body 1
4 GM6013 Check Valve 1
5 GM6029 Flexolite Gasket 1
6 GM6162 Washer 1
7 GM6209 Tap ¼” 1
8 GM6211 Tap 1” 1
9 GM6235 Screw 4
10 GM6261 Screw 6
11 GM6334 Mechanical Seal 1
12 GM6346 Counterface 1
13 GM7103 Nut 1
14 GM8613 Impeller 1
15 GMF156 Key 4x4x16 1
16 GM5505 Motor Bracket 1
17 GM6321 Bearing 1
18 GM6854 Condenser 50 For CPE 30 A1 1
19 GM7187 Elastic washer 1
20 GM8010 Rear Motor Cover 1
21 GM8011 Vis 4
22 GM8013 Bearing 1
23 GM8014 Motor Stator For CPE 30 A1 (1 HP) 1
24 GM8016 Fan 1
25 GM8017 Fan Cover 1
26 GM8018 Junction Box Cover 1
27 GM8052 Motor stator For CPE 30 A3 (1PH) 1
28 GM8286 Condenser Clip 1
29 GM8652 Motor Shaft 1
30 GM8659 Motor (1PH) 1
31 GM8660 Motor (3PH) 1
Motor Pump