Classic Accessories Fairway Deluxe 3-Sided GolfCar Enclosure User guide

Fairway
CLASSIC
Assembly and Care
Instructions
Deluxe 3-Sided Golf
Car Enclosure

2
Congratulations on the purchase of your Fairway Deluxe 3-Sided
Golf Car Enclosure.
First assembly will take about twenty minutes and is best done with two
people. However, once complete, much of it will not have to be repeated and it
will go much faster.
If you refuse to read instructions save yourself time and effort and read the
bold faced notes.
Safety
Periodically check to be sure that the top is not sagging over the side doors, that the
under-car straps are snug and that the lower hooks are not loose near the wheels.
Cleaning
Don't clean the plastic windows when they are dry—you can scratch them.
The best way to clean your windows is to hose them with water and to rub with your
bare hands or a very soft cloth. Liquid soap may be used.
During freezing weather an automotive windshield solvent and a soft cloth will work.
Fabric areas of the cab may be washed with a rag or soft bristle brush and a mild soap.
Storage
Store in a clean dry place. Never store a wet enclosure off of the car in an enclosed
area as it can become mildewed. Mildew can cause permanent stains.
Avoid folding the plastic windows of the enclosure for long periods. Wrinkles can be
relaxed with a hair dryer but take care not to melt the plastic.
Warranty
Your Fairway Deluxe 3-Sided Golf Car Enclosure is factory warranted for
workmanship and materials for three years from the date of purchase.
This warranty assumes normal use and conditions and does not include rental use.
ALWAYS remove the enclosure before transporting your golf car on a truck or trailer.
Use during transportation will invalidate your warranty.
Fairway
Deluxe 3-Sided Golf Car Enclosure
Assembly and Care Instructions

3
Deluxe 3-Sided Golf Car Enclosure
Parts List
Windshield Strap
Carrying Case
Four
1" x 8"
adhesive
hook
strips
Two 1" x 32" adhesive hook strips
3 Side Golf Car Enclosure
(Passenger side of the enclosure not shown in this view).
REAR
FRONT
(driver's side)

4
Important! Before Fitting!
If at all possible, do steps 1-2 one to
two days before first use. This is to
allow the adhesive on the hook and
loop to cure.
Important! Club Cars 1983-07!
If you have a 1983-2007 Club Car
you will need to install an adapter
bar after step 2. Please refer to the
instructions with the adapter bar.
If the adapter bar is not included
with this enclosure you can get
one from your retailer or from
Classic Accessories.
TOOLS NEEDED:
• Scissors
• Small wood block or
piece of cardboard
1. Apply adhesive hook strips
to your car front roof posts.
Remove your enclosure from the storage bag
and locate the plastic bag holding the adhesive
backed hook strips. Remove the two longest
32" strips.
If you have a folding windshield skip to step 1b.
1a. For non-folding windshields:
Attach one of the 32" strips to the outside (not
the front) of one of your cars' front roof posts
on either side of the windshield. Hold the strip
vertical and peel an inch or so of the adhesive
backing from the top end.
Align the strip along the
roof post with the top of the
strip just where the post
straightens out below the
roof line. Slowly peel off the
backing as you press the strip
down the post. If there is a
plastic windshield channel
attached to the post cut
the strip at the edge of the
plastic and start a new piece
on the aluminum post.
Using a small wood block
or piece of cardboard press
the strip firmly down along
the entire length of the post.
Now put the other 32" strip
on the opposite roof post.
1b. For folding
windshields:
If you have a folding windshield you can follow
the instructions above in 1a except you need
to cut the adhesive backed hook strip to allow
space for where the rubber windshield
fittings attach.
Fold your windshield up and mark the top and
bottom of where the rubber fitting cinches on the
roof post.
Cut the 32" strip into individual pieces to go
above and below your marks and then attach
them to the roof posts.
Wait one to two days for the glue to cure
before proceeding.
Fairway
Deluxe 3-Sided Golf Car Enclosure
Assembly and Care Instructions

5
2. Attach the enclosure to the top of
the windshield.
Find the side release buckle at the top left side
of the enclosure and attach it around the driver’s
side front roof post just below the roof. Walk the
enclosure around your car and attach the right
top side to the roof post on the passenger side.
Don't worry if the enclosure sags at this point.
3. Attach the enclosure front to the
hook strips on the front roof posts.
At the front of your enclosure there is a fabric
triangle with three long strips of black loop
material on it. Depending on what type of golf car
you have one of these strips mates to the hook
material you applied to the car front roof posts
(See illustration on this page for details). Find
the correct strip and fold the leading edge of the
enclosure to the inside. The web loops now face
forward. Secure the loop strips on the enclosure
to the hook strips on the roof posts.
Note that you may need to adjust the top strap
slightly for the hook and loop strips to line up.
4. Apply the
windshield strap.
Locate the plastic bag containing the velcro and
straps and remove the single strap shown below.
This strap lies across the hood below the
windshield and holds the two front ends of the
enclosure together.
The C-shaped ends on this
strap attach to web loops
facing forward at the bottom
of the long black loop on the
enclosure front. (See above
for the correct loop to fit your
brand of golf car).
Fit the C-shaped end of the
strap to into the web loop
and the C-shaped end of the
Front fold-back
placement for
Club Car
Yamaha
EZ Go
Windshield strap
placement for
Club Car
Yamaha
EZ Go
Fit the C-shaped
plastic on the
ends of the strap
into the web
loops on the
enclosure front.

If you run out of room on the ratchet, loosen
the ratchet buckle by pressing the black button
in the center of the lever and loosen the ratchet
to the first ‘click’. Then retighten the cam buckle
and following that the ratchet buckle.
When the enclosure is straight on the sides
over the doors and there is no sagging, close the
ratchet lever, fold up the and cover the buckles
with the protective fabric flap.
6. Attach the enclosure to the wheel
wells and bumper.
Remove from the bag containing the strap and
velcro the four 1" x 8" pieces of adhesive backed
hook material.
Near each wheel cutout toward the bottom you
will find a strip of loop material sewn to the inside
of your enclosure. Note where the loop on the
enclosure contacts the car, mate the hook strip
to the loop strip on the enclosure, remove the
adhesive backing and press the strip on the car in
side-release buckle into the opposite web loop
on the other side of the car.
Clip the strap buckle into the buckle end on
the web strap and tighten the strap. Slip excess
strap under the strap keeper and slide the strap
keeper down toward the end of the excess strap.
5. Cinch the top tight from the back.
Your enclosure hangs from a top strap that
encircles the top of the four car roof posts.
When this top strap is tight your enclosure will
stay up and be secure.
At the top and back of the enclosure is a fabric
flap covering a cam buckle and a ratchet buckle
to tighten the top strap.
Open the flap and locate the strap exiting from
the cam buckle on the right side. Holding the
back of the enclosure up toward the roof, tighten
this strap until the enclosure is held up along the
top of your car just along the roof line.
Now tighten the top strap further with the
ratchet buckle at the left. To tighten, lift the
ratchet lever up to the left. Each time you
move the lever the ratchet will tighten the
strap one ‘click’.
6
Ratchet Cam
Buckle (lever up) Buckle
Tightening the strap with the ratchet buckle.
Strap Keeper
Tightening the strap at the cam buckle.
Ratchet Cam
Buckle Buckle
(lever down)
Ready to
remove the
adhesive
backing
from the
hook strip
and apply
near the
front wheel

the noted spot. Repeat with the other wheels.
Next, find the hooks on the inside of the
enclosure near the top of the rear wheel well.
Secure the hooked straps on each rear wheel well.
Keep your face and eyes clear of the hook and
straps when you connect them. The elastic strap
can snap back if the hook fails to connect.
7. Attach the bottom hooks to the
sides of your car.
Attached to the inside of the cover, near the
bottom on either, side are two hooks for attaching
the cover to the bottom of the golf car. Each hook
is attached to the cover by an elastic strap. Grasp
each hook and stretch to attach to the bottom
edge of the golf car. Keep your face and eyes
clear of the hook and straps when you connect
them. The elastic strap can snap back if the
hook fails to connect.
8. Attach the rear window.
Attach the rear window by slipping the top of
the rear window under the two top flaps on the
enclosure and mating the hook and loop tabs on
the window and the enclosure flaps.
The back window also attaches at the sides
and bottom with hook and loop strips.
On either side of the trunk opening are two
adjustment straps that can be used to adjust
the enclosure length to your car.
To keep from scratching the rear window
plastic on the clubs use club covers or put a
cloth over the top of the clubs and bag.
9. Opening the doors and windows.
The rear window, trunk door and side doors can
all be held open.
The rear
window can be
rolled-up and
held open with
straps at the top
of the window.
To hold the
trunk door open you can either fold one of the
bottom corners up and mate the hook tab on the
inside of the door to the loop tab on the flap at
length
adjustment
straps
rear window
attachment
tabs
7

the door top,
or you can roll
the door up and
attach it to the
top flap.
The side
doors can be
held open
to either the
inside or the
outside. Just
attach the snap hook to the ‘D’-ring on the top of
the enclosure.
You may want to put the door on the inside for
periods of good weather and on the outside in
bad weather.
(Bottom
corner of
door is held
up with a
hook and
loop tab
If you clip the door to the outside fold the
bottom corner of the door up and fix the loop
tab on the inside to the loop tab sewn on the
upper inside of the door. This will keep the
bottom of the door out of the way of the
rear wheel.
The door zippers can also be used as a window
for ventilation if the top zipper pull is lowered.
Enjoy your enclosure!
Door open to the outside. Door open to the inside.
Trunk door can be held open
with this flap
07cG59_001
22640 68th Ave. S. Tel: [phone]
Kent, WA, USA 98032 Fax: [phone]
www.classicaccessories.com
Email: customerser[email protected]
Classic Accessories, Inc
©2007 Designed in the U.S.A.
72042 72092 72992
Classic Accessories, Inc