Classic Accessories 52-001-010401-00 User manual

08cH56_10158
Questions, problems, missing parts? Before returning to your retailer, call Classic Accessories customer service at
1-800-854-2315, 8 a.m. - 4 p.m., PST, Monday-Friday. Email: [e-mail]
WARNING
READ YOUR INSTRUCTIONS COMPLETELY AND CAREFULLY BEFORE ATTEMPTING TO SET UP YOUR NEW SNOW THROWER
CAB OR OPERATE YOUR SNOW THROWER WITH YOUR CAB INSTALLED.
English
Español (página 13)
Français (page 25)
ITEM/ARTÍCULO/ARTICLE #52-001-010401-00
SNOW THROWER CAB
A VIDEO OF THIS INSTALLATION IS AVAILABLE FOR DOWNLOAD AT:
www.classicaccessories.com/instructions

2
TABLE OF CONTENTS
Safety Information ................................................................................................................................................................................. 2
Package Contents List (Parts and Hardware)....................................................................................................................................... 3
Package Contents List (Soft Parts)....................................................................................................................................................... 4
Preparation ............................................................................................................................................................................................ 5
Assembly Instructions ........................................................................................................................................................................5-9
Care and Maintenance .........................................................................................................................................................................10
Troubleshooting ....................................................................................................................................................................................10
Warranty................................................................................................................................................................................................10
Replacement Parts ...............................................................................................................................................................................10
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any
questions regarding the product please call Classic Accessories customer service at 1-800-854-2315, 8 a.m. - 4 p.m., PST,
Monday-Friday.
1. THE CAB IS NOT A PROTECTIVE DEVICE.
The cab will NOT protect against noise, engine exhaust, chemicals, collision, roll-over or other accidents.
2. Follow all your snow thrower manufacturer’s recommended safety instructions.
3. Operating a snow thrower with this cab will restrict your field of vision.
Watch carefully for people, children, obstructions or obstacles.
4. The cab adds height to your snow thrower.
Remember the height of your cab. Watch carefully for tree limbs or other items overhead that you could previously go under
without a cab.
5. Before use be sure that all bolts are tight.
If one or more bolts comes loose failure of cab parts may occur.

3
PACKAGE CONTENTS LIST (PARTS)
FRAME PARTS HARDWARE PARTS
Part Description Quantity
ACenter Mounting Bar 1
B1, B2 Side Mounting Bar 2
C1, C2 Mounting Bar End 2
D1, D2 Front Bottom Poles 2
E1, E2 Front Top Poles 2
FBack Hoop Side Poles w/PVC sleeves 4
GBack Hoop Corner Poles 2
H Back Hoop Top Pole 1
IFront Hoop Side Poles w/PVC ends 4
JFront Hoop Top Pole 1
Part Description Quantity
K1, K2 Front Mounting Plate 2
L1, L2 Rear Mounting Plate 2
MU Bolt 4
NNylock Nut 8
A
F
F
F
FM
N
B1
C1
K1, K2
L1, L2
D1
E1
E2
D2
B2
C2
H
I
G
G
J

4
PACKAGE CONTENTS LIST (CONTINUED) SOFT PARTS
Please note: Some parts listed may not be used during installation.
The use of some parts are dependent on the model of your snow thrower.
Part Description Quantity
OCab Fabric Skin 1
O

5
PREPARATION
Before beginning assembly, installation or operation of the product, make sure all parts are present. Compare parts with the
package contents list and diagram. If any part is missing or damaged, do not attempt to assemble, install or operate the product.
Contact customer service for replacement parts.
Estimated Assembly Time: 20-30 minutes
Tools Required for Assembly:
Adjustable wrench or one 1/2 in. box end wrench
ATTACH THE MOUNTING BAR (FIGS. 2A AND 2B)
2. Position assembled mounting bars horizontally, slide
two U-bolts [M] from the backside of the snow thrower
(not the motor side) through the rear mounting plate [L]
and the front mounting plate [K] positioned on the front
side. Thread a Nylock nut [N] on each U-bolt stud. Snug
but do not fully tighten. Repeat on the other handlebar
upright. (Fig. 2a)
Please see the diagrams below for correct and incorrect
installation of the mounting plates. (Fig. 2b)
Note: The preferred mounting location for assembled
mounting bar is on the front (motor side) of the
handlebars. The mounting bar should be placed on the
handlebars a minimum of 24" and a maximum of 30"
from the ground (as measured from the bar end). This will
allow headroom of at least 6.5' in the peak of the
cab roof.
CAUTION: Position of the clamps may vary
depending on snow thrower manufacture.
Select the highest position possible that will
accommodate the clamps and not interfere with the
snow thrower controls and frame.
CAUTION: Make sure nothing interferes with the
safe operation of your snow thrower.
Fig. 1a
Fig. 1b
A
B1
B2
Correct Incorrect
Fig. 2a
Snow thrower
handlebar
uprights
Fig. 2b
M
M
L
K
N
ASSEMBLY INSTRUCTIONS
ASSEMBLE THE MOUNTING BAR (FIGS. 1A AND 1B)
1. Insert both side mounting bars [B1 & B2] into
the center mounting bar [A]. (Fig. 1a)
Secure by engaging the spring loaded pins
as shown. (Fig. 1b)

6
Fig. 3
ASSEMBLE THE REST OF THE FRAME (FIG. 3)
3. Insert the mounting bar ends [C1, C2] into the side mounting
bars by engaging the spring loaded buttons.
4. Insert the front top poles [E1, E2] into the front bottom poles
[D1, D2]. Install each assembled front pole into the vertical
stud on the top of each side of the mounting bar.
5. Insert back hoop side poles [F] into the vertical stud on each
side mounting bar. Insert another pair of back hoop side
poles into the tops of the ones installed on the side mounting
bars. Insert the back hoop corner poles [G] into the tops of
the installed sections of frame hoop side poles. Finish by
inserting the back hoop top pole [H] into both frame hoop
corner poles.
Note: The back hoop side and corner poles each have clear
plastic sleeves on one end. The back hoop top pole [H]
DOES NOT have a clear plastic PVC sleeve.
C1
C2
E1
F
H
F
F
F
E2
D1
D2
G
G
Note: These parts should
already be installed on
the snow thrower
Remove protective plastic
caps from these metal
studs prior to assembly

7
Fig. 4
INSTALL THE FRONT HOOP POLES (FIG. 4)
6. Insert the front hoop side poles [I] first into each
assemble front pole on the frame. Insert another
pair of front hoop side poles into the one installed
on the front poles. Finish by carefully inserting
the front hoop top pole [J] into both the top
most front hoop side poles, forming a curve. The
curved poles will be standing quite high up in the
air. This is normal. (Fig. 4)
Note: The front hoop side poles
each have a PVC sleeve [I] on one
end. The front hoop top pole [J]
DOES NOT have a sleeve on either
end. During assembly, make sure
the poles ends with the PVC sleeves
face up.
J
I
I
I
I
CAUTION: Use care when
assembling the front
hoop side and top poles.
Poles under tension can
slip out of the sleeves
causing serious injury.

8
INSTALL THE FABRIC CAB SKIN TO THE ASSEMBLED FRAME (FIG. 5)
7. Unfold the fabric cab skin [O] and find the pocket sewn into
the top rear part of the cab skin roof. Carefully insert the top
curved section of the assembled front hoop poles into the
pocket on the cab skin. The front hoop poles and roof of
the cab skin will rest on top of the assembled frame
hoop poles. (Fig. 5)
8. Unfold the rest of the cab skin and drape over
the assembled frame as shown.
Fig. 5
Note: The lower front panel features two double zip-
pers that allow convenient pass-through of cables
or linkages if necessary
O

9
SECURE FABRIC CAB SKIN TO FRAME (FIG.6)
9. Find the large fabric strap sewn into the bottom rear area
of the fabric cab skin. Pull the strap down and over the
end of both mounting bar ends [C1, C2]. (Fig. 6)
Find all rip and grip tabs on the inside of the cab skin and
secure the skin to the frame.
Note: If it is very difficult to secure straps over the
mounting bar ends, make sure that all rip and grip tabs
are loose and that the skin is fitted correctly.
Fig. 6
FINE TUNE THE PLACEMENT OF THE CAB ON SNOW THROWER AND SECURE
10. Adjust the cab so it is centered over the controls and the angle of the mounting bar ends
are parallel to the ground by loosing the U bolts and mounting clamps and readjusting.
Fully tighten all nuts and screws when complete.
Enjoy your new Snow Thrower Cab!
Loosen nuts to change angle
of mounting bar
Fig. 7
C1, C2

1 0
CARE AND MAINTENANCE
STORAGE
Store in a clean dry place. Never store a wet cover in an enclosed area as it can develop mildew.
Avoid folding the plastic windows of the cover for long periods.
BOLTS
Check all bolts before each use to see that they are tight. If one or more bolts come loose, failure of cab parts may occur.
WINDOWS
Don't clean the plastic windows when they are dry—you can scratch them.
Hose them with water and rub them with your bare hands. Liquid soap may be used.
During freezing weather an automotive windshield solvent and a soft cloth will work (don't use your bare hands with the solvent).
Fabric areas of the cab may be washed with a rag. Don't use soap as it may remove protective coatings added by the factory.
TROUBLESHOOTING
WARRANTY
The manufacturer, Classic Accessories, Inc., will repair or replace, without charge, this product which under normal usage has
proven to be defective in its manufacture or workmanship for a period of two (2) year from the date of initial retail purchase. This
warranty is valid only to the original purchaser. This warranty is not transferable and does not cover any parts that have been
subjected to misuse, abuse, alteration, overload, accident or normal wear of moving parts.
Service can be obtained by contacting Classic Accessories at 1-800-854-2315. Any cab or cab part that is returned to Classic
Accessories, together with the original sales receipt as proof of initial retail purchase, and with postage prepaid, will be repaired or
replaced without cost if the unit is found defective. This warranty does not apply to accessories or damage caused where repairs
have been made or attempted by others. All warranty work will be completed in a reasonable time, not to exceed 60 days after
receiving the product.
Classic Accessories is not responsible for direct, indirect, incidental or consequential damages. Some states do not allow
limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental damages, so the
above limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights, which
vary from State to State.
WARRANTY VOID IF PRODUCT USED FOR COMMERCIAL OR RENTAL PURPOSES OR IF THE SNOW THROWER CAB IS
TRANSPORTED ON AN OPEN TRAILER OR TRUCK.
Call: 1-800-854-2315 for Warranty Assistance, Monday - Friday 8:00 a.m. - 4:00 p.m., PST
REPLACEMENT PARTS
If parts are missing or if you need replacement parts, please call Classic Accessories customer service at 1-800-854-2315,
8 a.m. - 4 p.m., PST, Monday-Friday. Please refer to the Package Contents List for the parts list.
Problem Possible Cause Corrective Action
Cab front interferes with the
snow thrower controls.
Upper horizontal mounting bar
[A, B1 & B2] is mounted too low.
1. Rotate cab forward.
2. Move cab sideways.
Not enough headroom. Upper horizontal mounting bar
[A, B1 & B2] is mounted too low.
1. Rotate cab forward.
2. Raise attachment point

11

22640 68th Ave. S. Tel: [phone]
Kent, WA, USA 98032 Fax: [phone]
www.classicaccessories.com
Email: [e-mail]
©2008 Designed in the U.S.A.
08cH56_10158
Printed in China