Claypaky A.LEDA B-EYE K10 EASY User manual

1
A.LEDA B-EYE K10 EASY
A.LEDA B-EYE K10
A.LEDA B-EYE K20
C61415
C61419
C61420
INSTRUCTION MANUA
Congratulations on choosing a Cla Pak product!
We thank ou for our custom.
Please note that this product, as all the others in the rich Cla
Pak range, has been designed and made with total qualit to
ensure excellent performance and best meet our expectations
and requirements.
Carefully read this instruction manual in its entirety and keep it
safe for future reference. It is essential to know the information
and comply with the instructions given in this manual to ensure
the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting
or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and
without prior notice.
ENG ISH
INDEX
Page
2
4
5
6
8
18
19
20
21
Contents
Safety information
Unpacking and preparation
Installation and start-up
Control panel
Menu setting
Maintenance
Cause and solution of problems
Technical information
Channel functions

2
A.LEDA B-EYE
SAFETY INFORMATION
0.2
LED
IP20
tc90°C
Risk Group 2
According to
EN 62471
• Installation
Make sure all parts for fixing the projector are in a good state of repair.
Make sure the point of anchorage is stable before positioning the projector.
The safety chain must be properly hooked onto the fitting and secured to the framework, so that, if the primary
support system fails, the fitting falls as little as possible.
If the safety chain gets used, it needs to be replaced with a genuine spare.
• Minimum distance of illuminated objects
The projector needs to be positioned so that the objects hit by the beam of light are at least 0.20 metres (8”) from
the lens of the projector.
• Minimum distance from flammable materials
The projector must be positioned so that any flammable materials are at least 0.20 metres (8”) from every point on
the surface of the fitting.
• Mounting surfaces
It is permissible to mount the fitting on normally flammable surfaces.
• Maximum ambient temperature
Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).
• IP20 protection rating
The fitting is protected against penetration by solid bodies of over 12mm (0.47”) in diameter (first digit 2), but not
against dripping water, rain, splashes or jets of water (second digit 0).
• Protection against electrical shock
Connection must be made to a power supply system fitted with efficient earthing (Class I appliance according to
standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the projectors from indirect
contact and/or shorting to earth by using appropriately sized residual current devices.
• Connection to mains supply
Connection to the electricity mains must be carried out by a qualified electrical installer. Check that the mains
frequency and voltage correspond to those for which the projector is designed as given on the electrical data label.
This label also gives the input power to which you need to refer to evaluate the maximum number of fittings to
connect to the electricity line, in order to avoid overloading. A.leda B-EYEK20: the user must determine, in
consultation with the supply authority, that the equipment is connected only to a supply with a maximum permissible
system impedance Zmax, at the interface point of the user’s supply, equal to 0.29 Ω or less.
• Temperature of the external surface
The maximum temperature that can be reached on the external surface of the fitting, in a thermally steady state, is
90°C (194°F).
• Maintenance
Before starting any maintenance work or cleaning the projector, cut off power from the mains supply.
• ight collimation system
This product contains internal light collimation system. Avoid intense light from any angle.
• Photobiological Safety
CAUTION. Possibly hazardous optical radiation emitted from this product. Do not stare at operating lamp. May be
harmful to the eyes.
This product is intended for the following areas of application:
studios, stages, theaters, exhibitions, trade fairs, events, theme parks, entertainment venues, architectural lighting
and similar
Not suitable for household illumination
Not for residential use

3
A.LEDA B-EYE
LiFePO4
Pb
• Battery
This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment,
please dispose the battery at the end of its life according to the regulation in force.
• Disposing
This product is supplied in compliance with European Directive 2012/19/EU - Waste Electrical and Electronic
Equipment (WEEE). To preserve the environment please dispose/recycle this product at the end of its life according
to the local regulation.
The products to which this manual refers comply with the European Directives pursuant to:
• 2006/95/EC - Safety of electrical equipment supplied at low voltage (LVD)
• 2004/108/EC - Electromagnetic Compatibility (EMC)
• 2011/65/EU - Restriction of the use of certain hazardous substances (RoHS)

4
A.LEDA B-EYE
UNPACKING AND PREPARATION
1
A.LEDAB-EYEK10EASY
A.LEDAB-EYEK10
A.LEDAB-EYEK20
C61415
C61419
C61420
INSTRUCTIONMANUAL
CongratulationsonchoosingaClayPakyproduct!
Wethankyouforyourcustom.
Pleasenotethatthisproduct,asalltheothersintherichClay
Pakyrange,hasbeendesignedandmadewithtotalqualityto
ensureexcellentperformanceandbestmeetyourexpectations
andrequirements.
Carefully read this instruction manual in its entirety and keep it
safe for future reference. It is essential to know the information
and comply with the instructions given in this manual to ensure
the fitting is installed, used and serviced correctly and safely.
CLAY PAKY S.p.A. disclaims all liability for damage to the fitting
or to other property or persons deriving from installation, use and
maintenance that have not been carried out in conformity with this
instruction manual, which must always accompany the fitting.
CLAY PAKY S.p.A. reserves the right to modify the
characteristics stated in this instruction manual at any time and
without prior notice.
ENGLISH
PRELIMINARY
INDEX
Page
2
3
4
5
7
15
17
17
18
Contents
Safety information
Unpacking and preparation
Installation and start-up
Control panel
Menu setting
Maintenance
Technical information
Cause and solution of problems
Channel functions
IST009/001
2 x 183102/805
1
90°
90°
90°
90°
LOCKED
UNLOCKED
PAN Mechanism ock and Release (every 90°) - Fig. 2
2
Packing contents - Fig. 1

5
A.LEDA B-EYE
3
1
2
3
2
1
4
INSTA ATION AND START-UP
Connecting and disconnecting power cable - Fig. 4
Installing the projector - Fig. 3
The projector can be installed on the floor resting on special rubber feet, on a truss or on the ceiling or wall.
WARNING: with the exception o when the projector is positioned on the loor, the sa ety cable must be itted. (Cod. 105041/003 available on request).
This must be securely ixed to the support structure o the projector and then connected to the ixing point at the centre o the base.

6
A.LEDA B-EYE
Switching on the projector - Fig. 7
Press the switch. The projector starts resetting the effects. At the same time, the following information scrolls on the display:
Model Firmware xxx (Fixture ID) System errors
A.leda B-EYE Version X.X.X Dmx Address xxx E: .........................
Date - Hour W: .........................
On conclusion of resetting in case of absence of the dmx signal, Pan and Tilt move to the “Home” position (Pan 50% - Tilt 50%). The control panel
(Fig. 7) has a display and buttons for the complete programming and management of the projector menu. The display can be in one of two conditions:
rest status and setting status. When it is in the rest status, the display shows the projector’s DMX address and the Fixture ID address (if set).
During menu setting status, after a wait time (about 30 seconds) without any key having been pressed, the display automatically returns to rest status.
It should be noted than when this condition occurs, any possible value that has been modified but not yet confirmed with the
F
key will be cancelled.
CONTRO PANE
0.2m
1
2
Dmx Address
Warning Message
Fixture ID
7
Connecting to the control signal line (DMX) - Fig. 6
Use a cable conforming to specifications EIA RS-485: 2-pole twisted, shielded, 120Ohm characteristic impedance, 22-24 AW , low capacity. Do not use
microphone cable or other cable with characteristics differing from those specified. The end connections must be made using XLR type 3 or 5-pin male/female
connectors. A terminating plug must be inserted into the last projector with a resistance of 120Ohm (minimum 1/4 W) between terminals 2 and 3.
IMPORTANT: The wires must not make contact with each other or with the metal casing of the connectors. The casing itself must be connected to the
shield braid and to pin 1 of the connectors.
Mains
5
6
SIGNAL
SCREEN
DMX 512
5 PIN
1
2
3
4
5
SIGNAL
SCREEN
1
3
2
DMX 512
3 PIN
SIGNAL
SIGNAL
Connecting to the mains supply - Fig. 5

7
A.LEDA B-EYE
28
28
Reversal of the display - Fig. 8
To activate this function, press UP
B
and DOWN
C
keys simultaneously while the display is in the rest mode. This status will be memorised and
maintained even for the next time it will be switched on. To return to the initial state, repeat the operation all over again.
Setting the projector starting address
On each projector, the starting address must be set for the control signal (addresses from 1 to 512).
The address can also be set with the projector switched off.
Setting the address: see pag. 11.
Setting the projector Fixture ID
On each projector, the Fixture ID address must be set for an easy identification of the fixtures in an installation (ID from 1 to 255).
The Fixture ID address can be set with the projector switched off.
Setting the Fixture ID: see pag. 11.
8
Functions of the buttons - Using the menu
Setting addresses and options with the projector disconnected
The projector’s DMX address, as well as other possible operating options, can also be set when the appliance is disconnected from the electricity supply.
All that is needed is to press
F
to momentarily activate the display and thus access the settings. Once the required operations have been carried out,
the display will switch off again after a wait time of 30 seconds.
USING THE MENU:
1) Press
F
once – “Main Menu” appears on the display.
2) Use the UP
B
and DOWN
C
keys to select the menu to be used:
• Setup (Setup Menu): To set the setting options.
• Option (Option Menu): To set the operating options
• Informations (Informations Menu): To read the counters, software version and other information.
• Manual Control (Manual control Menu): To trigger the test and manual control functions.
• Test (Test Menu): To check the proper functionning of effects
• Advanced (Advanced Menu): Access to the "Advanced menu" is recommended for a trained technical personnel.
To enable the "Advanced" see pag. 15.
3) Press
F
to display the first item in the selected menu.
4) Use the UP
B
and DOWN
C
keys to select the MENU items.
Confirms the displayed value, or activates the displayed function, or enters the successive
menu.
Decreases the value displayed (with auto-repetitions) or passes to the next item in the menu.
Increases the value displayed (with auto-repetitions) or passes to the previous item in a menu.
Return to the top level.
Commute from units, tens, hundreds, in the "Address", "Fixture ID" and "Calibration" menù.
F
C
DOWN
B
UP
D
LEFT
E
RI HT
Continue ➔

8
A.LEDA B-EYE
MENU SETTING
XXX = default value
Main Menu Level 1 Level 2 Level 3 Choices / Values
SET UP
Basic Engine
Mode Standard
Shape
Source DMX
Art-net
Universe 0 - 255
DMX Address 1 - 512
Pixels Engine
Mode
Disabled
RGB
RGBW
Source DMX
Art-net
Universe 0 - 255
DMX Address 1 - 512
Repeat on DMX Enablement Disabled
Enabled on primary
Universe 0 - 255
Ethernet Interface Control Protocol
Disabled
Art-net on IP 2.x.x.x
Art-net on IP 10.x.x.x
Fixture ID 0 - 255

9
A.LEDA B-EYE
Main Menu Level 1 Level 2 Level 3 Choices / Values
OPTION
Pan / Tilt
Invert Pan On / Off
Invert Tilt On / Off
Swap Pan-Tilt On / Off
Encoder Pan-Tilt On / Off
P/T Homing mode Standard
Sequenced
Pan Home Def Pos
0 degree
90 degrees
180 degrees
270 degrees
Tilt Home Def Pos
0 %
12.5 %
25 %
50 %
75 %
87.5 %
100 %
Silent Mode Standard
Quiet
Fan Speed Mode Auto
Full
Display On / Off
Special Functions
Pan/Tilt speed Normal
Fast
Dimmer curve
Curve 1
Curve 2
Curve 3
Curve 4
RGB Gamma
Gamma 1.0
Gamma 1.5
Gamma 2.0
Halogen Mode
Halogen OFF
Halogen Lamp 1
Halogen Lamp 2
Halogen Lamp 3
Halogen Lamp 4
Halogen Lamp 5
Setting
Default Preset Reset To Default
Go Back
User Preset 1 Load preset 1
Save to preset 1
User Preset 2 Load preset 2
Save to preset 2
User Preset 3 Load preset 3
Save to preset 3
Continue ➔

10
A.LEDA B-EYE
Main Menu Level 1 Level 2 Level 3 Choices / Values
INFORMATION
System Errors Read / Reset
Fixture Hours Total Hours Read
Partial Hours Read / Reset
LED Energy Tot Total Hours Read
Partial Hours Read / Reset
System Version
Aleda fw Fw.rev.
CPU board Hw.rev.
com.dev Fw.rev.
0:PT-3f Fw.rev. / Hw.rev.
1:Ld-k20 Fw.rev. / Hw.rev.
Board Diagnostic 0:PT-3f Status / Err%
1:Ld-k20 Status / Err%
DMX Monitor Channels Value / Percentage
Fans Monitor
PwrSp Speed (RPM)
PwrSp Speed (RPM)
Head Speed (RPM)
Sensor Status
Pan ON / OFF / n.a.
Tilt ON / OFF / n.a.
Zoom Rotation ON / OFF / n.a.
Zoom ON / OFF / n.a.
Network parameters
IP Address
IP Mask
MAC Address
MANUAL
CONTROL
Reset Yes / No
Channels Value / Percentage
TEST
Pan / Tilt
Colour
Zoom
Rotation
All
Zoom Rotation
Sensor Test
ADVANCED Access Code 1234
Upload Firmware Yes / No
Setup Model Yes / No
Calibration Channels 000 - 255
LED calibration
LED Selection 01-37 Red 0-255
Green 0-255
Blue 0-255
White 0-255
Reset To Default
LED Calibration

11
A.LEDA B-EYE
For greater programming ease using the DMX control unit and Media-
server Art-net, channel mapping is divided into BASIC EN INE and
PIXEL EN INE (see details in Channel Function).
BASIC ENGINE
Mode
This lets you select the projector operating mode for BASIC EN INE,
selecting one of the two available modes:
• Standard (see channel mapping in Channel Function)
• Shape (see channel mapping in Channel Function)
Source
It lets you assign the input source the projector receives signals from dedicated
to BASIC EN INE. One of the two available sources can be selected:
• DMX
• Art-net
Universe
It lets you set “DMX Universe” for BASIC EN INE mode to assign values
between 000 and 255 to a series of projectors (This option is valid only if
Source= Art-net)
DMX Address
It lets you select the address (DMX Address) for the control signal by
BASIC EN INE. A DMX address between 001 and 512 can be selected.
NOTE: Without the DMX input signal, the displayed address (DMX
Address) blinks.
PIXE S ENGINE
Mode
This lets you select the projector operating mode for PIXELS EN INE,
selecting one of the three available modes:
• Disabled
• R B (see channel mapping in Channel Function)
• R BW (see channel mapping in Channel Function)
Source
It lets you assign the input source the projector receives signals from dedicated
to PIXELS EN INE. One of the two available sources can be selected:
• DMX
• Art-net
Universe
It lets you set “DMX Universe” for PIXELS EN INE mode to assign
values between 000 and 255 to a series of projectors (This option is valid
only if Source= Art-net)
DMX Address
It lets you select the address (DMX Address) for the control signal by
PIXELS EN INE. A DMX address between 001 and 512 can be selected.
REPEAT ON DMX
Enablement
It lets you enable/disable the transmission of the Ethernet protocol by
DMX signal to all the connected projectors.
• Disabled: DMX transmission disabled.
• Enabled on primary: DMX transmission enabled.
Universe
It lets you set the “DMX Universe” to assign values between 000 and 255
to a series of projectors. In this case it refers to an Art-net input not read
by the projector and re-transmitted to other projectors.
ETHERNET INTERFACE
It lets you set the Ethernet settings to be attributed to the projector.
Control Protocol
It lets you select the Art-net “Control Protocol” to be assigned according
to the control unit used. The following options are available:
• Disabled
• Art-net on IP 2.x.x.x
• Art-net on IP 10.x.x.x
FIXTURE ID
It lets you set the “Fixture ID” to be assigned to the projector. An “ID”
between 000 and 255 can be assigned.
SET UP MENU
NOTE: On grey the default options
Set Up
Basic
Engine Mode
Source
Universe
Dmx
Address
Pixels
Engine Mode
Source
Universe
Dmx
Address
Repeat
on DMX Enablement
Universe
Ethernet
Interface
Control
Protocol
Fixture ID
Continue ➔

12
A.LEDA B-EYE
PAN / TI T
Invert pan
Used for reversing Pan movement.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B
and DOWN
C
keys to enable (On) or disable (Off)
PAN inversion.
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
Invert tilt
Used for reversing tilt movement.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B
and DOWN
C
keys to enable (On) or disable (Off) Tilt
inversion.
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
Swap Pan-Tilt
Used for swapping Pan and Tilt channels (as well as Pan fine and Tilt fine).
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B
and DOWN
C
keys to enable (On) or disable (Off)
Pan and Tilt channel swap.
3)Press
F
to confirm the selection or LEFT
D
to keep current settings.
Encoder Pan-Tilt
Used for enabling the Pan / Tilt encoders.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B
and DOWN
C
keys to enable (On) or disable (Off)
Pan / Tilt encoders.
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
You can quickly disable the Pan and Tilt Encoder by simultaneously
pressing the UP
B
and DOWN
C
keys in the ''Main Menu''.
P/T Homing Mode
Lets you set the initial projector Reset mode.
1) Press
F
, the current setting appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following settings:
Standard: Pan & Tilt are simultaneously reset.
Sequenced: Tilt is reset first followed by Pan.
3) Press
F
to confirm the selection or LEFT
D
to keep the current setting.
Pan Home Def Pos
Lets you assign the Pan channel “home” position at the end of Reset,
without a DMX input signal.
1) Press
F
, the current setting appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following
settings:
0 degree
90 degrees
180 degrees
270 degrees (default)
3) Press
F
to confirm the selection or LEFT
D
to keep the current setting.
Tilt Home Def Pos
Lets you assign the Tilt channel “home” position at the end of Reset,
without a DMX input signal.
1) Press
F
, the current setting appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following settings:
0%
12.5%
25%
50% (default)
75%
87.5%
100%
3) Press
F
to confirm the selection or LEFT
D
to keep the current setting.
SI ENT MODE
It lets you select the “Silent Mode” from the two available.
1) Press
F
the current setting appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following settings:
Standard: Maximum speed and consequently maximum effects/fans
noise level.
Quiet: Regulates the speed of the effects (Pan, Tilt, Zoom, Zoom rotation) and
of the fans thereby reducing their noise level.
3) Press
F
to confirm the selection or LEFT
D
to keep the current setting.
OPTIONS MENU
Swap
Pan-Tilt
On
Off
Encoder
Pan-Tilt
On
Off
Pan / Tilt
Option Invert
Pan
On
Off
Invert
Tilt
On
Off
P/T Homing
Mode
Standard
Sequenced
Pan Home
Def Pos
Tilt Home
Def Pos
Silent
mode Standard
Quiet

13
A.LEDA B-EYE
DISP AY
Used for automatically reduce brightness on the display after about 30
seconds in idle.
1) Press
F
- the current settings appear on the display (On or Off).
2) Use the UP
B
and DOWN
C
keys to enable (On) or disable (Off)
the decreasing of display brightness.
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
FAN SPEED MODE
Allows you to set how to manage the fan speed of the head of the fixture,
select between the two available:
• Auto: the head’s fan varies the speed depending on the temperature
detected on the LED.
• Full: the head’s fan is always at full speed.
SPECIA FUNCTIONS
Pan / Tilt speed
Lets you select two different Pan and Tilt speeds.
1) Press
F
- the current setting appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following settings:
- Normal
- Fast
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
Dimmer Curve
Lets you select four different Dimmer channel curves.
1) Press
F
- the current setting appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following
settings:
- Curve 1
- Curve 2
- Curve 3
- Curve 4
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
RGB Gamma
Lets you select three different R BW gamma curves.
1) Press
F
- the current setting appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following settings:
- Gamma 1.0
- Gamma 1.5
- Gamma 2.0
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
Halogen Mode
Lets you select five different halogen lamp simulations.
1) Press
F
- the current setting appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following
settings:
- Halogen OFF
- Halogen amp 1 - 750 W
- Halogen amp 2 - 1000 W
- Halogen amp 3 - 1200 W
- Halogen amp 4 - 2000 W
- Halogen amp 5 - 2500 W
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
SETTING
Used to save 3 different settings of the items in the options menu and
relative submenus.
1) Press
F
- “Default preset” appears on the display.
2) Use the UP
B
and DOWN
C
keys to select one of the following
configurations:
- Default preset (*)
- User preset 1
- User preset 2
- User Preset 3
3) Press
F
- “Load preset X” appears on the display.
4) Use the UP
B
and DOWN
C
keys to select:
- Load preset X to recall a previously stored configuration.
- Save to preset X to store the current configuration.
a confirmation message (Are you sure?) appears on the display.
5) Select YES to confirm the selection or NO to keep the current setting
and return to the next higher level.
(*) DEFAULT PRESET
Save To
Preset 3
Reset To
Dafault
o Back
Setting Default
Preset
Load
Preset 1
Save To
Preset 1
User
Preset 1
Load
Preset 2
Save To
Preset 2
User
Preset 2
Load
Preset 3
User
Preset 3
Dimmer
Curve
R B
amma
Halogen
Mode
Special
Functions
Pan / Tilt
speed
On
Off
Display
Auto
Full
Fan Speed
Mode
Continue ➔

14
A.LEDA B-EYE
By pressing the RIGHT
E
key and the EFT
D
key simultaneously
once entered in the "main menu" it is possible to quickly (short cut)
reset the default settings (DEFAU T PRESET).
Used for restoring default values on all options menu items and relevant
submenus.
1) Press
F
, a confirmation message (Are you sure?) appears on the display.
2) Select YES to confirm the selction or NO to keep current setting.
SYSTEM ERRORS
Shows a list of warnings and messages relevant to errors occurred since
the fixtures switching-on.
1) Pressing
F
you are allowed to reset the SYSTEM ERRORS list.
A confirmation message (Are you sure you want to clear error list ?)
appears on the display.
2) Select YES to reset the list or NO to go back.
FIXTURE HOURS
Used for displaying projector operating hours (total and partial).
1) Press
F
- Hours total and partial appears on the display.
Total counter
Counts the number of projector working life hours (from manufacture to date).
Partial counter
Counts the number of partial projector working life hours since the last
reset to date.
2) Press
F
to reset partial projector working hours a confirmation
message (Are you sure?) appears on the display.
3) Select YES to reset partial projectors counter or NO to keep the current
setting and return to the top menu level.
ED ENERGY TOT
Lets you view total LED working hours.
1) Press
F
- to display total and partial Watts/hour:
Total
Total LED working hours from construction to date.
Partial
LED working hours from last reset to date.
2) Press
F
to reset the partial counter. A confirmation appears on the
screen (Are you sure?)
3) Select YES to reset the partial counter or NO to keep the current setting
and open the next menu level.
SYSTEM VERSION
Used for displaying the software and hardware version of each board
installed in the projector.
CPU brd (CPU board)
0: PT-3f (Scheda Pan / Tilt)
1: Ld - Kxx (Scheda LED)
BOARD DIAGNOSTIC
Used for displaying the status error of each board installed in the projector:
0: PT-3f (Scheda Pan / Tilt)
1: Ld - Kxx (Scheda LED)
DMX MONITOR
Used for displaying the projector DMX channel level in bit (Val) and in
percentage (Perc).
FANS MONITOR
Used for displaying the speed of each fan installed in the projector:
PwrSp (fan PSU)
Head (fan head)
SENSOR STATUS
It lets you check the correct operations of each "sensor” installed in the
projector, each channel is associated with one of the following three
parameters:
• n.a.= sensor not available
• ON= sensor working
• OFF= sensor defective
INFORMATION MENU
Information System
Errors
Fixture
Hours
Total XXX
Partial XXX
Reset...
LED Energy
Tot
System
Version
Board Revis. Hw.rv.
CPU brd x.x.x x.x
com.dev x.x
0: PT-3f x.x x.x
1: Ld - Kxx x.x x.x
Sensor
Status
Dmx
Monitor
Board Status Err%
0:PT-3f ood 0.00
1: Ld - Kxx ood 0.00
Fans
Monitor
Fan Speed (RPM)
PwrSp XXXX
Head XXXX
Board
Diagnost.
Option

15
A.LEDA B-EYE
NETWORK PARAMS
Allows the "Network" parameters of the projector to be displayed or:
IP address: Internet Protocol address (two projectors must not have the
same IP address)
IP mask: 255.0.0.0
Mac address: Media Access Control: the projector’s Ethernet Address.
RESET
Used for resetting the projector.
1) Press
F
to reset the projectors, a confirmation message (Are you
sure ?) appears on the display.
2) Select YES to starting reset the fixture or NO to keep the current setting
and return to the top menu level.
CHANNE
Used for setting channel levels from the projector control panel.
1) Press
F
- the first channel appears on the display.
2) Use the UP
B
and DOWN
C
keys to select the required channel:
3) Press
F
and use the UP
B
and DOWN
C
keys to select the
required DMX level (value between 0 and 255).
4) Press LEFT
D
to return to the top menu level.
TEST
Allows you to check the proper functioning of effects.
1) Press
F
to return to the top menu level.
2) Use the UP
B
and DOWN
C
keys to select the required test.
3) Press
F
to confirm the selection or LEFT
D
to keep current settings.
Test sequence:
Pan - Tilt effects (Pan & Tilt)
Colours
Zoom
Zoom rotation
All effects
Zoom Rotation Sensor Test
To enable the "Advanced Menu" set up the "Access code" (1234) using the
UP
B
, DOWN
C
, RI HT
E
keys.
Press
F
- "Menu advanced" appears on the display
UP OAD FIRMWARE
Allows you to transfer the firmware from 1 fixture to all the connected fixtures.
1) Press
F
, a confirmation message appears on the display.
2) Select YES to start the firmware loading or NO to keep the current set-
ting and return to the top menu level
SETUP MODE
Allows you to change the default model of projector.
1) Press
F
a confirmation message appears on the display.
2) Select YES to define the model of projector or NO to keep the current
setting and return to the top menu level.
CA IBRATION
Allows you to adjust effects from the control panel to obtain perfect unifor-
mity between the projectors.
1) Press
F
- “channels” appears on the display.
2) Using the UP
B
and DOWN
C
keys, select the effect you wish to
regulate.
3) Press
F
and use the RI HT
E
, UP
B
and DOWN
C
buttons to
make the adjustment by setting a value between 0 and 255.
4) Press
F
to confirm the selection or LEFT
D
to keep current set-
tings and return to the top level.
FACTORY DEFAU T
Allows you to restore default values of all channels (128).
1) Press
F
– a confirmation message appears on the display (Reset
calibration to factory default ?).
2) Select YES to reset calibration to factory default or NO to keep the
current setting and return to the top menu level.
Manual
Control
No
Yes
Reset
Channel
Test
Pan-Tilt
Colour
Zoom
Rotation
All
Zoom Rot Sens Test
Advanced
Code
1234
Calibration
Upload
Aleda fw
Transfer the firmware on all
the connected fixtures ?
Are you sure ?
Yes/No
Setup
Model
Changing to a wrong model
may damage the fixture.
Are you sure ?
Yes/No
MANUA CONTRO
TEST MENU
ADVANCED MENU
Network
params

16
A.LEDA B-EYE
9
WARNING:
no alcohol
CAUTION:
• ight collimation system
This product contains internal light collimation system. Avoid intense light from any angle.
To avoid damage to the internal parts of the fixture when the fixture is not working, is recommended to turn the head down before turning the fixture off, so
that the front lenses of the fixture are invested as little as possible from the sun or any intense light.
• Set channel 20 (Zoom) to 255-bit before turning off the projector to facilitate the packaging of the projector.
•To ensure optimal operation and performance for a long time it is essential to periodically clean the parts subject to dust and grease deposits. The
frequency with which the following operations are to be carried out depends on various factors, such as the amount of the effects and the quality of
the working environment (air humidity, presence of dust, salinity, etc.).
It is recommended that the projector undergoes an annual service by a qualified technician for special maintenance involving at least the following
operations:
- eneral cleaning of internal parts.
- Restoring lubrication of all parts subject to friction, using lubricants specifically supplied by Clay Paky.
- eneral visual check of the internal components, cabling, mechanical parts, etc.
- Electrical, photometric and functional checks; eventual repairs.
Cleaning the lenses
Only use neutral soap and water to clean the lenses, then dry it carefully with a soft, non-abrasive cloth. (WARNIN : the use of alcohol or any other
detergent could damage the lenses).
ight collimation system
This product contains internal
light collimation system. Avoid
intense light from any angle.

17
A.LEDA B-EYE
5
6
3
4
1
2
10
Battery removal - Fig. 10
This product contains a rechargeable lead-acid or lithium iron tetraphosphate battery. To preserve the environment, please dispose the battery
at the end of its life according to the regulation in force.
LiFePO4
Pb

18
A.LEDA B-EYE
1
2
3
4
2
1
1
1
1
11
12
Opening the covers - Fig. 11
Removing/Assembling the lens unit - Fig. 12
MAINTENANCE

19
A.LEDA B-EYE
CAUSE AND SO UTION OF PROB EMS
THE PROJECTOR WILL NOT SWITCH ON
PROBLEMS
ELECTRONICS NON-OPERATIONAL
DEFECTIVE PROJECTION
REDUCED LUMINOSITY
POSSIBLE CAUSES CHECKS AND REMEDIES
No mains supply.
LED exhausted or defective.
Signal transmission cable faulty or disconnected.
Incorrect addressing.
Fault in the electronic circuits.
Lenses or reflector broken
Dust or grease deposited.
Check the power supply voltage.
Call an authorised technician.
Replace the cables.
Check addresses (see instructions).
Call an authorised technician.
Call an authorised technician.
Clean (see instructions).
13
Replacing the line actuator - Fig. 13

20
A.LEDA B-EYE
479
(18.86")
358
(14.09")
253
(9.96")
423
(16.65")
248
(9.76")
360
(14.17")
290
(11.42")
Zoom IN
340
(13.39")
Zoom OUT
180
(7.09")
Zoom IN
230
(9.06")
Zoom OUT
589
(23.19")
476
(18.74")
370
(14.57")
460
(18.11")
380
(14.96")
Zoom IN
430
(16.93")
Zoom OUT
200
(7.87")
Zoom IN
250
(9.84")
Zoom OUT
395
(15.55")
330
(12.99")
494
(19.45")
358
(14.09")
253
(9.96")
423
(16.65")
248
(9.76")
360
(14.17")
350
(13.78")
Zoom OUT
310
(12.20")
Zoom IN
233
(9.17")
Zoom OUT
189
(7.44")
Zoom IN
TECHNICA INFORMATION
Power supplies available
100-240V 50/60Hz
Input power
• K20 - 750VA
• K10 - 450VA
Total output
B-EYE K10: 5500 lumens
B-EYE K10 Easy: 4800 lumens
B-EYE K20: 9800 lumens
ED source
Osram Ostar R BW LED - 15W
Average LED life: 50.000 h
Motors
5 (k10), 7 (k20) stepper motors, operating with microsteps,
totally microprocessor controlled.
Cooling
• High efficiency die-cast aluminium
•Forced ventilation
Inputs
• DMX 512
• Ethernet
Working position
Working in any position.
Moving Head
• Movement by means of two stepper motors, controlled
by microprocessor.
• Automatic repositioning of PAN and TILT after accidental
movement not controlled by control unit.
• Angle:
- PAN = 540°
- TILT = 210°
IP20 protection rating
• Protected against the entry of solid bodies larger than
12mm (0.47”).
• No protection against the entry of liquids.
CE Marking
Complies with the following European Directives
- 2006/95/EC (LVD)
- 2004/108/EC (EMC)
- 2011/65/EU (RoHS).
Weights
• K10: 14.5 kg (31.14 lbs)
• K20: 21 kg (46.3 lbs)
A. eda B-EYE K10
A. eda B-EYE K10 easy
A. eda B-EYE K20