CLEAR Lighting C-FR-F10 User manual

ARTIST OF LIGHT
LED NEON FLEX RIBBON
USER MANUAL
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE
INSTALLATION. LEAVE A COPY FOR THE END USER/MAINTENANCE
ENGINEER FOR FUTURE REFERENCE.
C-FR-F10 Lighting
Version No. : V2.0
R

Table
Of
Contents
02
C-FR-F10 USER MANUAL www.clearlighting.com
Unpacking
Basic Parameters
Cautions
Instructions for Cutting Light
Clasp Front Connector
Clasp End Cap
Snap Front Connector
Snap End Cap
Diagram of Light Wiring
Mounting Profile Options
Troubleshooting
Limited Warranty
Appendix
03
06
07
08
09
13
16
20
24
26
33
34
35
R

1 2
34
5 6
78
Unpacking
03
White Box Packaging
R

Note: Two people are needed to uncoil the light.
Unpacking
04
Reel Packaging
1
2
3
4
5
C-FR-F10 USER MANUAL www.clearlighting.com
R

Unpacking
05
Uncoiling Roller
Uncoiling Roller (Optional Device)
C-FR-F10 USER MANUAL www.clearlighting.com
Roll up the rest of the light
Protect the light end and fix it
Use recommended cutter to cut
the light vertically
Rotate the roller edge to uncoil the
light with another hand
Put the light on the middle of
uncoiling roller
R

Basic
Parameters
06
1. Dimension: 9*18mm
2. Min. bend diameter: 90mm
3. Protection rate: IP68/IP65
4. IP68 protection rate: Protected against dust and submersion in water (1 meter above).
5.The product IP rate is ultimately in line with properly applied IP rated connectors.
6. Easy to use, with a range of accessories for joining, terminating, mounting&powering.
7. Long Iifetime: 5 years.
8. Working ambient temperature: -20°C~45°C (High Voltage: -20°C~25°C ) .
9. Ope rating(bending)ambient temperature: 0°C~45°C.
C-FR-F10 USER MANUAL www.clearlighting.com
01
9mm
18mm
Max.Running Length
20m for single end feed
40m for double ends feed
15m for single end feed
30m for double ends feed
7.5m for single end feed
15m for double ends feed
80m for single end feed
Min.Cutting Length
125mm(9LEDs)
83.3mm(6LEDs)
4.17mm(3LEDs)
1000mm(72LEDs)
LED Spacing
13.89mm
13.89mm
13.89mm
13.89mm
Rated Power/m
3.5W
4.5W
4.5W
5W
Working Voltage
D24CV
D24CV
D12CV
Ac230
LED Qty/mtr
72LEDs
72LEDs
72LEDs
72LEDs
Appearance of Cover*
WM
WM
WM
WM
Light Color
R/A
G/B/W
R/A/G/B/W
R/A/G/B/W
B
Light Type: C-FR-F10
Note: Unless otherwise stated, the tolerance of the light is ±0.3mm.
*
NOTE: Appearance of Cover
1 2
WM=White PVC Housing +Milky Light-emitting Surface
Note 1: Housing color is the light color except from the light-emitting surface.
Note 2: Light-emitting surface color is the color without light up.
R

Twist the light
Bend along light surface
Light Surface
WARNING: The above wrong approaches will damage the light.
Light Surface
Light Surface
Do not bend smaller than allowed minimum bend diameter 90mm.
Cautions
07
C-FR-F10 USER MANUAL www.clearlighting.com
1. Before making any cuts, installation, maintenance or
connection, be sure the mains is disconnected!
2. Note: all connector joints must be connected correctly to
achieve IP68 rating.
3. Please operate this flex light by instructions, and confirm the
work voltage, it must be matched with product requirements.
4. Please confirm the polarity of connector before insertion front
connection cable.
5. Connect and cut this product correctly. Any wrong operation
will damage this product.
6. Using qualified DC power supply.
7. Please correctly use and bend this flex ribbon light, see the
figures on the right.
90 mm
01 |0 2
01 |02
01|02
01 |02
Light Surface
R

01 0 2
01 0 2
01
Instructions
for
light
cutting
08
Note: The cutting surface should be flush and smooth.
The Min. cutting length
(see as the feature)
Cutting line
Please don’t cut from light -emitting surface.
Cutting line
Don't allow to cut away from the cutting line.
Don't cut slantingly
The cutting surface must be flush and smooth.
WARNING: The above mishandling will damage the light.
Note:
1. Place the light horizontally when cutting it.
2.Use only factory-recommended cutter.
3.Cut the light according to the following instructions.
Incorrect operation will damage the light
C-FR-F10 USER MANUAL www.clearlighting.com
Cutting line
02
01 02
R

09
C-FR-F10 USER MANUAL www.clearlighting.com
Clasp Front
Connector
Please ignore these steps if the front
connector has been assembled before
delivery.
Finished Assembly View
1.Components of Front
Connector
2.Tools
Feed Connector (1pc)
[Contain Silicone Gasket(1pc)]
Anti-skidding Clip (1pc) U Steel Plate (1pc)
Inducer Gripper
Explosive View
02
Note:
1. Never wet the assembly units or assemble with
wet hands.
2. Please use the tools correctly.
3. Please pay attention to personal security when
using tools.
R

PCB Insertion Placement
PVC Tape
10
C-FR-F10 USER MANUAL www.clearlighting.com
3.Installation Steps
3.1 Inducing a Cavity for Feed Connector
Insert the inducer to the backside of PCB around 10~12mm,
move the inducer up and down 3~5 times gently to create a
small cavity.
3.2 Insert the Feed Connector
Insert the inducer into the backside of PCB It will damage the light if insert into front
side of PCB
Insert the feed connector pins into the
cavity that you created with the
inducer (backside of PCB)
The following operations are prohibited:
Insert into the front side of the PCB Insert crosswise into the PCB Insert crosswise into the PCB
NEVER insert into the front side
(LED side) of the PCB
R

11
3.3 Treatment of Anti-skidding Clip
Unfold the anti-skidding clip about 20 degrees on both sides.
Fit the anti-skidding clip to the end of the light
tightly and align with the light end edge.
Place the anti-skidding clip
onto the end of the light. Notice
its installation direction.
3.4 Installation fo U Steel Plate
C-FR-F10 USER MANUAL www.clearlighting.com
Push the bulging points on the anti-skidding
clip into th slots on the U steel plate.
R

12
C-FR-F10 USER MANUAL www.clearlighting.com
3.5 Push the anti-skidding clip to the end
until the two hook splinters on each side pop
out to lock the U steel plate. Use the gripper
to help tighten the piece.
Please energize the light to check its
functionality and do waterproof
reliablity testing (refer to "waterproof
reliability testing instruction" video)
after connector assembly.
R

13
C-FR-F10 USER MANUAL www.clearlighting.com
Clasp
End Cap
Please ignore these steps if the end cap
has been assembled before delivery.
1.Components of End Cap
2.Tools
Tail Plug (1pc)
Silicone Gasket(1pc)
Anti-skidding Clip (1pc) U Steel Plate (1pc)
Gripper
Explosive View
Finished Assembly View
Note:
1. Never wet the assembly units or assemble with
wet hands.
2. Please use the tools correctly.
3. Please pay attention to personal security when
using tools.
R

14
3.Installation Steps
3.1 Place the tail plug into the U steel plate
C-FR-F10 USER MANUAL www.clearlighting.com
3.2 Treatment of Anti-Skidding Clip
Unfold the anti-skidding clip about 20 degrees on both sides.
Place the anti-skidding clip onto the end of the light.
Notice its installation direction.
Fit the anti-skidding clip to the end of the light tightly
and align with the light end edge.
The silicone gasket is attached on the tail plug.
R

15
C-FR-F10 USER MANUAL www.clearlighting.com
3.3. Installation of Tail Plug
Push the bulging points on the anti-skidding
clip into the slots on the U steel plate.
3.4 Push the anti-skidding clip to the end
until the two hook splinters on each side pop
out to lock the U steel plate. Use the gripper
to help tighten the piece.
Please energize the light to check its
functionality and do waterproof
reliablity testing (refer to "waterproof
reliability testing instruction" video)
after connector assembly.
R

16
C-FR-F10 USER MANUAL www.clearlighting.com
Please ignore these steps if the front
connector has been assembled before
delivery.
Snap
Front
Connector
Finished Assembly View
Explosive View
1. Components of Front Connector
Feed Connector (1pc)
Anti-skidding Clip (1pc) PC Cover (1pc)U Steel Plate (1pc)
[Contain Silicone Gasket (1pc)]
2. Tools
Inducer
Note:
1. Never wet the assembly units or assemble with
wet hands.
2. Please use the tools correctly.
3. Please pay attention to personal security when
using tools.
R

Pay attention to the direction marked on the
bottom of PC cover.
17
3.1 Inducing a Cavity for Feed Connector
Insert the inducer to the backside of PCB around 10~12mm,
move the inducer up and down 3~5 times gently to create a
small cavity.
Insert the inducer into the backside of PCB It will damage the light if insert into front
side of PCB
NEVER insert into the front side
(LED side) of the PCB
3.1 Placing PC Cover
3. Installation Steps
Snap end of PC Cover Rear end of PC Cover
The assembly end
C-FR-F10 USER MANUAL www.clearlighting.com
PCB Insertion Placement
PVC Tape
R

18
The following operations are prohibited:
Insert into the front side of the PCB
Insert crosswise into the PCB Insert crosswise into the PCB
It will be a 2~5mm gap.
Unfold the anti-skidding clip about 20
degrees on both sides.
Place the anti-skidding clip onto the assembly end of the light.
Pay attention to its direction
Fit the anti-skidding clip to the end of the light so that it wraps
tightly and its brim is aligned with the cut edge on both sides.
3.3 Inserting the Feed Connector
3.4 Treatment of Anti-skidding Clip
3.5 Installation of Anti-Skidding Clip
C-FR-F10 USER MANUAL www.clearlighting.com
W=2~5mm
R

19
Slide back the PC cover till it snaps
in the feed connector.
Press the feed connector and light
downwards at the same time till
bottom.
Align the feed connector and anti-
skidding clip with the U steel
plate.
3.6 Installation of U Steel Plate and PC
Cover
Please energize the light to check its
functionality and do waterproof
reliablity testing (refer to "waterproof
reliability testing instruction" video)
after connector assembly.
C-FR-F10 USER MANUAL www.clearlighting.com
R

20
Please ignore these steps if the End Cap
has been assembled before delivery.
Snap
End Cap
Finished Assembly View
Explosive View
1. Components of End Cap
2. Tools
Tail Plug (1pc)
[Contain Silicone Gasket (1pc)]
Anti-skidding Clip (1pc) U Steel Plate (1pc) PC Cover (1pc)
Inducer
C-FR-F10 USER MANUAL www.clearlighting.com
R