Clear One UNITE 200 Pro User manual

UNITE® 200 Pro PTZ HD Camera
Quick-Start Guide
QSG-0142-001v1.0 September 2021

UNITE® 200 Pro PTZ HD Camera
3QSG-0142-001v1.0 September 2021
ClearOne®Contacts
Headquarters Headquarters
5225 Wiley Post Way Suite 500 Tel: +1.801.975-7200
Salt Lake City, UT 84116
Sales Technical Support
Tel: [phone] Tel: [phone]
[email protected] [email protected]
Notices
© 2021 ClearOne, Inc. All rights reserved.
Information in this document is subject to change without notice.
Document: QSG-0142-001v1.0, September 2021
Before you set up the camera, read this manual carefully. Follow the setup instructions indicated in this manual.
Keep this manual for future use.
To prevent electric shock, do not remove screws or the camera housing. No self-serviceable parts are inside the housing.
Installation
Place product on a smooth flat surface, or bracket-mount. Avoid contact with any liquid, gas or solid material that may
cause corrosion.
Do Not Disassemble
This product has no user-repairable parts. Damage caused by unauthorized disassembly is not covered by warranty.
Electromagnetic fields at specific frequencies may affect image quality.
Important Safety Information
WARNING: TO
PREVENT FIRE
OR
ELECTRICAL
SHOCK
HAZARD, DO
NOT EXPOSE
THIS
PRODUCT TO
RAIN OR
MOISTURE
THE LIGHTING FLASH
AND ARROWHEAD
WITHIN THE TRIANGE IS
A WARNING SIGN
ALERTING YOU OF
DANGEROUS VOLTAGE
INSIDE THE PRODUCT.
THE EXCLAMATION POINT
WITHIN THE TRIANGLE IS A
WARNING SIGN ALERTING
YOU OF IMPORTANT
INSTRUCTIONS
ACCOMPANYING THE
PRODUCT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
SEE MARKING ON BOTTOM/BACK OF PRODUCT
RISK OF ELECTRIC SHOCK DO
NOT OPEN
AVIS RISQUE DU CHOC ELECTRIQUE
- NE PAS OUVRIR
Use only in
non-tropical
locations.
Use only at
altitudes of
2000 meters
or less.
CAUTION

UNITE® 200 Pro PTZ HD Camera
4QSG-0142-001v1.0 September 2021
Introduction to the UNITE 200 Pro PTZ HD Camera
Front View
Packing List
Verify that you have received all parts associated with each of the components.
Inspect your shipment carefully. If the shipment shows obvious signs of damage, retain original
boxes and packing material for inspection by the carrier, and contact them immediately. ClearOne is
not responsible for product damage incurred during shipment.
• UNITE 200 Pro Camera
• Remote Control
• AC Power Adapter with Power Cord
• PoE Splitter
• RS-232 cable
• USB 3.0 cable, Type A and Type B
connectors
Lens
Remote Control
Sensor
Power
Indicator
Standby
Indicator

UNITE® 200 Pro PTZ HD Camera
5QSG-0142-001v1.0 September 2021
a. System Select Switch
b. RS-232 Out Port
c. RS-232 In Port
d. RJ45 Port
e. Reserved Port
f. Line In Port
g. Reserved Port
h. HDMI Port
i. USB 3.0 Port
j. Reserved Port
k. DC In 12 V Port
l. Power Switch
abcdl
kjih
Back View
Bottom View
m.Bottom Switches
n. Tripod Screw Hole
o. Fixing Screw Hole
m
n
o
eg
f

UNITE® 200 Pro PTZ HD Camera
6QSG-0142-001v1.0 September 2021
Connect
Make connections as shown in the following diagram:
Set Switches
DIP Switches
On the bottom of the unit, set both switch 1 and switch 2 to Off.
SW - 1 SW - 2 Mode
1 Off Off Normal Working Mode
2 On Off -
3 Off On -
4 On On -
Video System Switch
On the backplane of the unit, set the switch to the desired settings.
Video format options:
VIDEO SYSTEM
0 1080p60 8 720p30
1 1080p50 9 720p25
2 1080I60 A -
3 1080I50 B -
4 720p60 C -
Computer, TV, VCR w/audio input jack, Router/Switch, Speaker Microphone
AC Adapter*
PoE Splitter*
RS-232
(not included) RS-232
(included)
Audio
(not included)
HDMI & USB 3.0
(included)
Caution: Do not apply
power until after you set the
switches.
Note: After you change the switch, for the change to take effect,
you must restart the camera.
Ethernet*
(not included)
* Power options
• Use the PoE splitter to connect to power and ethernet, or
• Use the AC adapter, and an ethernet cable to connect the RJ-45 port to an external device.
Cable & PoE
(not included)

UNITE® 200 Pro PTZ HD Camera
7QSG-0142-001v1.0 September 2021
5 720p50 D -
6 1080p30 E -
7 1080p25 F -
Start Up
1. If you are not using the PoE Splitter, connect the AC power adapter to a power source.
2. On the back panel of the UNITE 200 Pro, set the Power Switch to On.
When the camera starts, Pan-Tilt rotates to the maximum position of top right, then returns to the center position. This
completes the initialization process.
Note: If the position preset 0 has been stored, then after initialization, the position preset 0 is called
up.
If you want to restore the factory default settings:
a. Press the Menu button to display the On-screen Display (OSD) menu.
b. Select Menu >Restore Default > Restore.
c. Set the value Yes, then press the HOME button.
IR Remote Control
Note: Power consumption in standby mode is approximately half of the normal mode
Standby Button
• Press this button to enter standby mode.
• Press it again to enter normal mode.
Position Buttons - to set or call a present
Zoom Buttons
• Slow Zoom: Zoom In [+] or Zoom Out [-] slowly
• Fast Zoom: Zoom In [+] or Zoom Out [-] fast
More detailed information about using the UNITE 200 Pro PTZ HD Camera is provided in the UNITE 200 Pro User Manual,
available in the ClearOne Resource Libary.