Clear Water CTA5 User manual

INSTALLATION
INSTRUCTIONS
Crystal single lever
bath filler
●We recommend that this product is installed by a qualified professional contractor. Such as a plumber who is certified by NVQ
(National Vocational Qualification) or SNVQ (Scottish National Vocational Qualification) Level 3.
●Please check this product immediately to ensure that it has not been damaged and is complete. Before installation, please make
sure this product is the correct model and you have all the parts required for installation and using.
●All the taps should be supplied with hot and cold water at balanced pressure. If not, then the mixing function will not work correctly.
It is necessary to fit non-return valves on both hot and cold feeds pipe. These are not supplied.
●Please flush the water system to ensure that no metal swarf, solder, and other impurities can enter the taps.
●
Turn off water supply before commencing work, this should be done at the isolating valves of inlet feeds if fitted or main stopcock.
●Please read these instructions carefully and keep it for future reference.
Working pressure
The tap is suitable for both high and low pressure installation. To ensure that the tap works well under low water pressure, the
cold water storage tank must be at least 2 meters above the installed position. The maximum water pressure is 6 bar. Where the
water pressure above 6 bar, then a pressure reducing valve must be fitted.
Maintenance
We do NOT recommend you use any household cleaners to clean the product. Because these cleaners change substance or formula
too frequently. The product should be always cleaned only with soapy water and rinsed with clean water and dried with a soft cloth.
FLOW STRAIGHTENER
Taps are all fitted with a flow straighter for use in low pressure installations.
An aerator is supplied in the box, and is an option that can be used in high
pressure installations. These can be interchanged by unscrewing the part,
and replacing with the alternate one. During the process do not loose the
washer, between the parts.
AERATOR
Straightener and aerator (alternative option)
Important
A
1 - 2
Cleaning
NOZZLE
Before use: Unscrew the filter and allow the water to run freely
for 5 minutes. Then screw the filter back in place.
Periodically: Unscrew the nozzle and remove. Rinse it with
running water until any loose debris is cleared.
Then replace the nozzle and tighten.
CTA5

A
Installation
Dimension
2 - 2
To remove the cartridge.
First shut off the water supply to the tap.
1: Pull out the cap from the handle.
2: Loosen the grub screw in handle, but do not remove it.
3: Take off the handle, unscrew the cartridge cover.
4: Using a correct size spanner unscrew the retaining nut.
5: Pull the cartridge and wash it with clean running water.
6. Dry and lightly grease the seals (only use silicone grease)
7: Replace them in turn.
MIXER BODY
CARTRIDGE
RETAINING
NUT
CARTRIDGE
COVER
HANDLE
ALLEN
KEY GRUB
SCREW
CAP
2-G3/4
197 108
Ø28
166
Ø55
Ø55
35
99
154
22
Max30
FLEXIBLE PIPES
LEFT: HOT FEED
RIGHT: COLD FEED
FIXING NUT
HANDLE
NOZZLE
MIXER BODY
WASHER
1: Fit the washer into the groove in the underside of the mixer body.
2: Screw the flexible pipes into the mixer body, and fully hand tighten.
3: Pass the tail of flexible pipes through the hole on the bath from above, and place the mixer in position on the bath, to see if any
alteration to the existing supply pipe work is necessary, make any necessary alterations to the pipe work.
4: Slide the fixing nut up the tails and onto the fixing bolt.
5: Check that the mixer body is correctly positioned, fully tighten the fixing nut.
6:
Connect the water supply pipe to the tail of flexible pipes with the hot water on the left and cold water on the right.

INSTALLATION INSTRUCTIONS
Crystal single Shroud - W24
Important
B
1 - 1
Maintenance
We do NOT recommend you use any household cleaners to clean the product. Because these cleaners change substance or formula
too frequently. The product should be always cleaned only with soapy water and rinsed with clean water and dried with a soft cloth.
Installation Dimension
●We recommend that this product is installed by a qualified professional contractor. Such as a plumber who is certified by NVQ
(National Vocational Qualification) or SNVQ (Scottish National Vocational Qualification) Level 3.
●Please check this product immediately to ensure that it has not been damaged and is complete. Before installation, please make
sure this product is the correct model and you have all the parts required for installation and using.
●Please read these instructions carefully and keep it for future reference.
1. Before installation, please flush the water system to ensure that no metal swarf, solder, and other impurities can enter the product.
2. Turn off water supply before commencing work, this should be done at the isolating valves of inlet feeds if fitted or main stopcock.
3. Build up water inlet pipe from ground.
4. Take away the washer and fixing nut before you install the bath tap on the standing tube.
5. Screw off the cover nut from standing tube.
6. Screw on the cover nut on the bath tap tail (no supplied). Then screw on the copper tubes (no supplied) also.
7. Slide the copper tubes into the standing tube and tighten the cover nut. Ensure that whilst installing the standing tube, the bath tap
is facing the correct direction.
8. Place the standing tube center of inlet pipe, and mark holes as per the bottom plate, drill and insert plug (if it is necessary).
9. Rise the standing tube on the inlet pipe, and fix the copper tubes to the inlet pipe.
10. Fix the standing tube on the floor with the supplied fittings (2 style screw & plug supplied, one is for Brick/Breezeblock floor,
the other is for wooden floor), finally put on the caps.
M34X1.5
Ø100
Ø55
736
Ø130
11.5
M5X4mm
GRUB
SCREW
2.5mm
ALLEN
KEY
2.5mm
ALLEN
KEY
BATH TAP TAIL (no supplied)
COVER NUT
COPPER TUBE (no supplied)
STANDING TUBE
SCREW
PLUG
4x
CAP
CONNECTOR
COLD INLET
HOT INLET
INLET PIPE (no supplied)