CLEBO-HD AID-2301 IR User manual

ABOUT MANUAL
Before installing and using the camera, please read this manual carefully.
Be sure to keep it handy for future reference.
Megapixel HD-SDI
Indoor Dome Camera
CLEBO-HD AID-2301 IR
05212012

2
PRECAUTIONS
FCC COMPLIANCE
WARNING : Changes or modifications are not expressly approved by the manufacturer.
Do not open or modify.
Do not open the case except during maintenence and installation,
for it may be dangerous and can cause damages.
Do not put objects into the unit.
Keep metal objects and flammable substances from entering the camera.
It can cause fire, short-circuits, or other damages.
Be careful when handling the unit.
To prevent damages, do not drop the camera or subject it to shock or vibration.
Do not install near electric or magnetic fields.
Protect from humidity and dust.
Protect from high temperature.
Be careful when installing near the ceiling of kitchen or a boiler room,
as the temperature may rise to high levels.
Cleaning :
To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.
Mounting Surface :
The material of the mounting surface must be strong enough to support the camera.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
Provide reasonable protection against harmful interference. when the equipment is
operated in a residential environment. This equipment generates, uses, and radiates
radio frequency energy; and if it is not installed and used in accordance with the
instruction manual, it may cause harmful interference to radio communications.

3
Table of Contents
Introduction
Installation
Camera OSD Menu and Glossary
Troubleshooting
Specifications
Features
Parts and Descriptions
Dimensions
Included Accessories
Easy Installations
Mounting on Electrical Junction Box
Connecting to Monitors
4
5
6
7
8~10
11
12
15-26
27
28
Adjusting the Camera 13
Adjusting the 3-Axis Gimbal 14

4
FEATURES*
Sony 1/2.8” CMOS Sensor
Highest Resolution 2.1 Megapixels
720P / 1080P Mode selectable
4x Auto-Focus 3.5~16mm Lens
Double Shutter WDR (Wide Dynamic Range) at 15fps Settings
70ft Range IR with Intelligent Camera Sync (CLEBO-HD AID-2301 IR)
Electronic Day and Night (CLEBO-HD AID-2301)
True Day and Night (CLEBO-HD AID-2301 IR)
AGC / BLC / AWB
3D DNR (3D Digital Noise Reduction)
D-Zoom (1~112 level)
HL Mask (High Light Masking)
Mirror Image Control
Programmable Privacy Zone (24) & Motion Detection
White defecet cancellation (DEFECT DET)
12VDC Support Only
Secondary Video-BNC Output

5
PART & DESCRIPTIONS*
2
3
7
9
5
6
1
8
41Lens
3RS485, Alarm
2Power input Connctor
12VDC Voltage
Yellow (485+)
Black (485-)
White (Alarm 1)
Red (Alarm 2)
4BNC (HD-SDI)
5Bubble
Camera Control Board
7
6Upper Case
82nd Video Connector
9Mounting Screws
w/o IR IR

6
DIMENSIONS IN MILLIMETERS(INCHES)*
89
108
Surface Mount Indoor
TOP VIEW
40,5
56,3
96,8
108 (4.25”)
(3.81”)
(1.59”)
(2.21”)
(4.25”)
3.50”)

7
INSTALLATION*
Included with Value Line Vandal Dome Camera
1. User Manual
2. Mounting Template
3. Second Video Jack
4. Four(4) Screw and Four(4) Dry Wall Anchors
123
4

8
EASY INSTALLATION*

9
SURFACE MOUNT INSTALLATION INSTRUCTIONS*
Squeeze the sides of the
camera and separate the
camera module from the
dome cover.
Use the camera’s mounting
template or your camera to
mark the holes as required.
Drill holes into the drywall and
insert the drywall mounts into
the holes.
Pull wires through and make
connections. Then, mount the
camera to the wall using the
included machine screws.
1 2 3
4
Adjust the camera lens
position by using the 3-Axis
Gimbal.
Snap the dome cover over
the camera module.
2 3

10
WALL MOUNT INSTALLATION INSTRUCTIONS*
Check to see all parts are in
the box.
Use the mount to mark the
pilot holes required. Drill
holes into the drywall and
insert the drywall mounts.
Secure the wall mount to the
wall using the mounting
screws.
Attach the base of the camera
to the wall mount with the
smaller machine screws.
Adjust the camera lens, and
snap the dome cover over
the camera module.
1 2 3
4 5

11
MOUNTING ON ELECTRICAL JUNCTION BOX*
NOTE : Screws required for electrical junction boxes are not supplied.These
screws are readily available at an electrical supply store.
Philips #8-32 x 0.75
2S
NO IR IR

12
CONNECTING TO MONITORS*

13
ADJUSTING THE CAMERA LENS*
Adjusting Auto Focus Lens
If pushing the OSD joystick to ‘UP’,
the lens will start zoom-in.
If pushing the OSD joystick to ‘DOWN’,
the lens will start zoom-out.
If you keep pushing the joystick,
zoom in/out will be continuously operated.
When you find the right angle, take off
your finger from the joystick and wait.
The focus will be automatically adjusted.
UP
DOWN

14
ADJUSTING THE 3-AXIS GIMBAL*
The Gimbal mechanism yields maximum rotation and placement as show below.
1Rotation 360 3Panning 360
NO IR IR NO IR IR
2Tilting 90
NO IR
4Tilting 82
IR

15
MODULE OSD MENU*
PROPERTY EXPOSURE LENS
FUNCTION IMAGE WDR/BLC
DAYNIGHT SET UP EXIT
CAMERA ID
0~255
TITLE
DISPLAY
NON, ID,, TITLE
PROTOCOL
PELCO-D, NADATEL
BAUDRATE
9600, 2400bps
RETURN
DZOOM
0~112
AWB
AUTO, AUTO_H, AUTO_L, PRESET,
MANUAL, AUTO-ext
PRIVACY
ON, OFF
DNR
OFF, LOW, MIDDLE, HIGH
MOTION
ON, OFF
RETURN
BRIGHTNESS
0~20
SHUTTER
AUTO, MANUAL(Indoor, Deblur120,
Deblur240, Outdoor)
DSS
OFF, x2, x3, x4
AGC
0~20
RETURN
LENS TYPE
MANUAL, DC, AF
MODE
OUTDOOR,INDOOR/FLK,Deblur120,Deblur240
OPTIC ZOOM TELE, WIDE
FOCUS MODE MANUAL, AUTO
FOCUSING FAR, NEAR
TIMER OFF, 1~10min
TDN SYNC OFF, ON
RETURN
CHROMA 0~20
SHARPNESS 0~10
MIRROR ON, OFF
FLIP ON, OFF
E-Edge ON, OFF
HLMASK ON, OFF
CONTRAST LOW, NORMAL, HIGH
HUE CONTROL R-GAIN, B-GAIN
RETURN
DETECT DET ON, OFF
2.0M MODE 1080P, 720P
720P MODE 60/50FPS, 30/25FPS
LANGUAGE ENG, GER, CHN
TDN TEST TEST OFF, TEST ON
FACTORY SET YES, NO
FREQ 60Hz, 50Hz
TYPE DOME, BOX, BULLET
FW_LOCK ON,OFF
RETURN
MAX DR OFF, ON
MODE OFF, BLC, WDR
WDR_WGT 0~9
BLC OSD OFF, ON
BLC POS-X 0~20
BLC POS-Y 0~20
BLC SIZ-X 0~20
BLC SIZ-Y 0~20
RETURN
TDN MODE
AUTO, COLOR, BW, LED
BW to C
0~9
C to BW
0~9
CDS SET
BW Low, BW High
RETURN
EXIT
No Save, Yes Save
RETURN

16
PROPERTY
1 PROPERTY
CAMERAID
TITLE(1-)
DISPLAY
PROTOCOL
BAUDRATE
RETURN
0
NONE
PELCO-D
9600 BPS
CAMERA ID
You can define the camera ID no. from 0~2550~255
(1-)
DISPLAY You can select whether displaying Camera ID and TITLE or not.NONE, ID, TITLE
PROTOCOL If using Nadatel HD-SDI DVR, select the protocol NADATEL.PELCO-D, NADATEL
BAUDRATE
RETURN
9600 is the default. There are 2 choices - 9600 and 2400bps.9600,2400bps
TITLE After setting the camera ID, you also can make the
title for each camera ID no. Title is total 8 figures
with number and alphabets.
Let me make the title name HDSDI123.
TITLE (1-H) H
TITLE (2-D) HD
TITLE (3-S) HDS
TITLE (4-D) HDSD
TITLE (5-I) HDSDI
TITLE (5-1) HDSDI1
TITLE (6-2) HDSDI12
TITLE (8-3) HDSDI123
1 PROPEARTY
CAMERAID
TITLE(1-H)
DISPLAY
PROTOCOL
BAUDRATE
RETURN
1
HDSDI123
NONE
PELCO-D
9600BPS

17
EXPOSURE
2 EXPOSURE
BRIGHTNESS
SHUTTER
DSS
AGC
RETURN
AUTO
OFF
10
20
BRIGHTNESS
You can adjust the brightness.
Higher number means brighter images.
The default is 10.
0~20
SHUTTER It’s a defualt. Shutter speed is adjusted properly.
Shutter speed is selectable from 1/30 ~ 1/60000 but
it’s related to the menu LENS-MODE.
AUTO
MANUAL
DSS (Digital Slow Shutter)
The default is OFF.
If better sensitivity is required, choose x2,3,or 4.
OFF, x2, x3, x4
AGC (Auto Gain Control)
Auto Gain Control automatically adjusts the video gain to enhance picture
brightness in low light conditions.The higher number means better sensitivity.
The default is 20.
0~20
RETURN
SHUTTER
LEVEL
RETURN 1/30
If LENS MODE is OUTDOOR, shutter
speed is adjustable from
1/30~1/60000.
If LENS MODE is INDOOR/FLK,
shutter speed is fxied with 1/30.
If LENS MODE is DEBLUR120, shutter
speed is adjustable from 1/30~1/120.
If LENS MODE is DEBLUR240, shutter
speed is adjustable from 1/30~240.

18
LENS
3 LENS
LENSTYHPE
MODE
OPTICZOOM
FOCUSMODE
TIMER
TDN SYNC
RETURN
AFLENS
DEBLUR120
T W
AUTO
OFF 00:00
OFF
LENS TYPE
AF LENS
DC LENS
MANUAL
AF mode is supported for Auto Focus Lens.
DC mode is supported for Auto-iris Varifocal lens.
Manual mode is supported for Manual iris or Fixed
board lens.
3 LENS
LENS TYHPE
MODE
OPTIC ZOOM
FOCUSMODE
TIMER
TDN SYNC
RETURN
DCLENS
DEBLUR120
If DC or Manual mode is selected, some
menu can’t be controlled - OPTIC ZOOM,
FOCUS MODE, TIMER, TDN SYNC.
It offers full range of eletric shutter speed from 1/30~1/60000.
It fixes shutter speed with 1/30. It can avoid color rolling problem.
It offers electric shutter speed from 1/30~1/120.
It offers electric shutter speed from 1/30~1/240.
Zoom Range is adjustable from Tele to Wide.
MODE
OPTIC ZOOM
OUTDOOR
INDOOR/FLK
DEBLUR120
DEBLUR240
Both DEBLUR120, DEBLUR240 helps to avoid motion blur at still image.

19
LENS
When using Auto Focus Lens, Focus can be adjusted automatically.
Also, you can set-up the TIMER to repeat the automatic focusing after finishing
the installation. TIMER is OFF and from 1 ~ 10min.
If you want to adjust the focus manually, select MANUAL mode.
In this case, TIMER menu will be changed to FOCUSING and you can adjust
the focus Far / Near.
OFF is default. If ON is seleced, the camera will adjust the focus when every
Day and Night filter change is operated.
FOCUS MODE
TDN SYNC
RETURN
AUTO
MANUAL
OFF / ON
3 LENS
LENSTYHPE
MODE
OPTICZOOM
FOCUSMODE
TIMER
TDN SYNC
RETURN
AFLENS
DEBLUR120
T W
AUTO
OFF 00:00
OFF
3 LENS
LENSTYHPE
MODE
OPTICZOOM
FOCUSMODE
FOCUSING
TDN SYNC
RETURN
AFLENS
DEBLUR120
T W
MANUAL
N < - > F
OFF

20
FUNCTION
4 FUNCTION
DZOOM
AWB
PRIVACY
DNR
MOTION
RETURN
0
AUTO
OFF
MIDDLE
OFF
DZOOM Digital Zoom function (Level 0~112)0~112
AWB White Balance is automatically adjusted.AUTO
R-GAIN
Color Temperature level.
It has LOW / MIDDLE / HIGH
KELVIN
White Balance is automatically adjusted in the
condition of Color temperature is high.
White Balance is automatically adjusted in the
condition of Color temperature is low.
AUTO_H
AUTO_L
White Balance is fixed with current setting.PRESET White Balance is manually adjustable.MANUAL Select AUTO-ext mode when using special
lightening like hallogen.
AUTO-ext
MWB
KELVIN
R-GAIN
B-GAIN
RETURN
MIDDLE 10
10
If MANUAL mode is selected, define the following menu.
It’s to adjust the amount of red in the image.
B-GAIN It’s to adjust the amount of blue in the image.