TP-Link vigi C445 User manual

Option 2: Route the cable through the side outlet. Insert anchors into the
holes and use screws to ax the camera base. Identify the groove and
alignment ridge on the camera. Begin by aligning the base's rim with the
camera's groove, attaching the ridge side rst for a correct t. Once aligned,
proceed to snap the rest of the camera onto the base to secure it.
Appearance
Camera Base
Speaker
7
IR LED × 4
6
White LED × 4
5
Built-in Microphone
1
2
Reset
3
microSD Card Slot
Unfasten the two xed screws to
remove the cover. Insert a
microSD card for local storage.
Initialize the SD card via VIGI app
or other management tools
before recording videos.
Power Supply Interface
(12V DC) *
9
RJ45 Network Interface
(supports PoE) *
8
4
1
3
2
56
4
89
3. Secure the Camera
Option 1: Route the cable through the wall/ceiling. Insert anchors into the
holes and use screws to ax the camera base. Identify the groove and
alignment ridge on the camera. Begin by aligning the base's rim with the
camera's groove, attaching the ridge side rst for a correct t. Once aligned,
proceed to snap the rest of the camera onto the base to secure it.
Stick the mounting template to the desired mounting place. Drill 4 screw
holes and 1 cable hole (for the cable through wall/ceiling) according to the
template.
1. Drill Holes 2. Open the Camera Case
Use the L-shaped hex metal screwdriver to loosen the hex screw, and use a
screwdriver to gently pry open the camera case. .
Quick Start Guide
1
Wall/Ceiling Mounting
4. Adjust the Surveillance Angle
Use the L-shaped hex metal screwdriver to loosen the hex screw on the
base, and adjust the surveillance angle as needed.
Cable Hole
(For the cable through wall/ceiling)
Hex screw
Side Outlet
*Images may dier from actual products.
L-shaped Hex Metal
Screwdriver
Mounting TemplateAnchors & Screws
Network Camera Quick Start Guide
Quick
Start
Guide
Unfasten the two xed screws to remove the
cover. Press for 5 seconds to reset the
camera to factory settings.
7
* The camera’s standard power supply is 12V DC or PoE (802.3af/at). The power
source should comply with Power Source Class 2 ( PS2) or Limited Power
Source(LPS) of IEC 62368-1 .
©2023 TP-Link 7106510682 REV1.0.2
Φ6 mm Φ3.5 mm
Waterproof Cable
Attachments
When installing with anchors
Φ = 6 mm (15/64 in.)
When installing with screws only
Φ = 3 mm (1/8 in.)
Appropriate drilling size (Φ)
Waterproof Seal
5
6
Hex screw
Rim
Alignment Ridge Rim
Alignment Ridge
Installing Waterproof Cable Attachments
Install the waterproof cable attachments for the network interface if needed.
Note: Make sure each part is securely attached and the waterproof rings are ush to keep out water.
1. Route the network cable through the following components in order: x nut,
waterproof ring, and then the waterproof jacket.
2. Fix the O-ring to the network interface of the camera and connect the network
cables.
3. Attach the network interface with the waterproof jacket, then twist to lock.
4. Insert the waterproof ring into the waterproof jacket. Rotate the x nut to
secure it to the waterproof jacket.
Fix Nut Waterproof
Ring
O-ring Network
Interface
Waterproof
Jacket
Install the waterproof seal for the power connectors when using a power adapter
to power the camera.
Install Waterproof Seal for Power Connectors
Male Power Connector Waterproof Seal Female Power Connector
5. Tighten the Hex Screw
Tighten the hex screw to secure the camera to the camera base. Hold the
camera and ensure the camera and base are as close together as possible
when tightening.
Tilt: 0° to 85°
Pan: 0° to 360°
Rotate: 0° to 360°

More Management Methods
1. Download the VIGI Security Manager on your
computer at
https://www.tp-link.com/support/download/vigi-s
ecurity-manager/.
2. Install the VIGI Security Manager and open it.
3. Cameras on the same network as your computer
can be automatically discovered. Go to Settings >
Discovered Devices, click + Add to activate your
discovered cameras by setting passwords, and
follow the instructions to add your cameras.
Method 1: Via the VIGI Security Manager
(Windows only)
You can also access and manage your cameras via any of the methods below.
View live video and modify camera settings on
your computer.
Method 3: Via a Web Browser
View live video and modify camera settings via a
web browser.
1. Find the camera's IP address on your router’s client
page.
2. On your local computer, open a web browser and enter
https://camera's IP address (https://192.168.0.60 by
default).
3. Select your Country/Region and Time Zone.
4. Set a password to activate the camera.
Done. You can view the live video on the Preview page, and
go to the Settings page to change camera settings.
Method 2: Via the TP-Link VIGI App
Remotely view live video, manage cameras, and
get instant alerts.
1. Download and install the TP-Link VIGI app.
2. Open the TP-Link VIGI app and log in with your
TP-Link ID. If you don’t have an account, sign up rst.
3. Tap the + button on the top right and follow the app
instructions to activate and add your cameras.
or
2Use Your Camera with an NVR
VIGI NVR
Monitor
Network Device
(e.g., Switch or Router)
Network Camera
Network Camera
The camera works with an NVR for easier batch access and management.
*Here we use a VIGI NVR as an example.
Frequently Asked Questions (FAQ)
Q1: What can I do if no cameras are discovered?
• Refresh to discover your camera again.
• Make sure the camera is powered on.
• Make sure your camera and NVR/computer are in the same subnet. If
not, use the VIGI Security Manager to set camera’s network
parameters.
• Try to add your camera manually.
• For other NVR brands, make sure you have activated the camera by
setting a password via the VIGI Security Manager, TP-Link VIGI app or web
management page.
Q2: How do I know the camera is powered on?
• The IR LED will turn on for 10 seconds once the camera is powered on. If
it’s o, you can cover the lens for several seconds and check if the IR LED
turns on.
• Check the Ethernet port LED status of the network device your camera is
connected to.
For more questions, please refer to
https://www.tp-link.com/support/faq/2850/
Step 2. Power On the Cameras
Power on your cameras with the PoE power supply or an
external power supply.
Note: The camera’s standard power supply is 12V DC or PoE (802.3af/at). The
power source should comply with Power Source Class 2 ( PS2) or Limited
Power Source(LPS) of IEC 62368-1 .
Step 1. Connect the Hardware
Connect your cameras to the same network as your NVR
(as shown above).
Step 3. Add Cameras with the NVR
Before you start, make sure your NVR is working properly.
1. Right click on the Live View screen, and click Add Camera.
2. Select your camera and click + to add your camera directly.
If you have disabled Plug and Play on your NVR, create a
password or use a preset password for your camera.
Note: If you can’t nd your camera, refer to FAQ-Q1.
Done! You can now view live video and manage cameras.
Using your cameras with other NVR brands:
Step 1: Power on your cameras and connect them to the network.
Step 2: Activate the cameras using the VIGI Security Manager, TP-Link VIGI app or web management page (refer to the next section).
Step 3: Refer to the NVR’s User Manual to add cameras.
• Do not use any other chargers than those recommended.
• Do not use damaged charger or USB cable to charge the device.
• Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
• Adapter shall be installed near the equipment and shall be easily accessible.
• Keep the device away from fire or hot environments. DO NOT immerse in water or any other liquid.
• Adapter should be used indoors where the ambient temperature is lower than or equal to 40 ℃.
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of
directives 2014/30/EU, 2014/35/EU, 2011/65/EU and (EU)2015/863.
The original EU Declaration of Conformity may be found at https://www.tp-link.com/en/support/ce/
For technical support, replacement services, user guides, and more information,
please visit https://www.tp-link.com/support, or simply scan the QR code.
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant
provisions of the Electromagnetic Compatibility Regulations 2016 and Electrical Equipment (Safety)
Regulations 2016.
The original UK Declaration of Conformity may be found at https://www.tp-link.com/support/ukca
Note: For more detailed instructions, refer to the user guides at
https://www.tp-link.com/support/