Clinton AS-892E User manual

ML892E-4
CLINTON
MODEL AS-892E
VARIABLE SPEED DC SERVO MOTOR
For
UNION SPECIAL
FEED-OFF-THE-ARM MACHINES
PEDESTAL MOUNT
40-0256-01
SERVICE MANUAL

TABLE OF CONTENTS
ML892E-5
®
SECTION I - INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
SECTION II - INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
A.
B.
C.
D.
E.
F.
G.
H.
MOTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SYNCHRONIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BELT GUARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LCD DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . .
CONTROL BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPEED CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
POWER AND CABLE CONNECTIONS . . . . . . . . . . . . . . . . . .
MOTOR ROTATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1
2-1
2-2
2-2
2-2
2-3
2-3
2-3
SECTION III - SYNCHRONIZER TIMING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
SECTION IV - PROGRAMMABLE LCD DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
A.
B.
C.
D.
E.
F.
MAXIMUM SEWING SPEED . . . . . . . . . . . . . . . . . . . . . . . . .
DIRECT ACCESS PARAMETERS . . . . . . . . . . . . . . . . . . . .
HIDDEN PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MASTER RESET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PULLEY RATIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TEST PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1. TREADLE TEST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. SYNCHRONIZER TEST. . . . . . . . . . . . . . . . . . . . . . . . . . .
3. ENCODER TEST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. DIVIDER TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1
4-1
4-3
4-4
4-4
4-4
4-4
4-5
4-5
4-5
SECTION V - CONNECTOR DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
SECTION VI - DRAWINGS AND PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
A.
B.
C.
D.
E.
F.
G.
H.
MAJOR ASSEMBLIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MOTOR ASSEMBLY, DC SERVO . . . . . . . . . . . . . . . . . . . .
CONTROL BOX ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . .
POWER SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SYNCHRONIZER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PROGRAMMABLE DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . .
E-PROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AIR CONTROL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . .
6-1
6-2
6-4
6-5
6-6
6-7
6-7
6-8
SECTION VII COMPLIMENTARY ASSEMBLIES . . . . . . . . . . . . . . . . . . . . . . . . 7-1
A.
B.
C.
D.
E.
F.
NEEDLE COOLER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
THREAD CATCHER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ELECTRIC EYE MTG. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FOOTLIFTER ASSEMBLY (U.S. 35800) . . . . . . . . . . . . . . .
FOOTLIFTER ASSEMBLY (U.S. 36200) . . . . . . . . . . . . . . . .
VENTURI ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-1
7-1
7-1
7-2
7-2
7-2

INTRODUCTION
Clinton's Model 892E is an electronically controlled variable speed drive for industrial sewing
machines. The system consists of a brushless DC Servo motor, a microprocessor powered
controller, a synchronizer, speed control, and programmable LCD display. No clutches or brakes
are used. All components interact to give a fast accurate and reliable sewing machine drive. The
components of the system are shown in figure below.
The model 892E has outputs for air thread saver, foot lift, needle cooler and stacker. It can be used
to operate all Clinton chain cutters, as well as various make and model chain cutters.
The programmable LCD display is used to select the desired mode. In addition, the display box is
used to select or change all parameters such as Speeds, Timers, Counters, Toggle Switches, etc.
1-1
SECTION I
®
ML892E-6
MOTOR
ON / OFF SWITCH
CONTROL BOX
SPEED CONTROL
WASTE CONTAINER
PROGRAMMABLE
LCD DISPLAY
SYNCHRONIZER
BELT GUARD

ML892E-7
SECTION II
®
INSTALLATION
A. MOTOR
Mount the motor to the pedestal base using the plate,
the motor support arms, the spacers, the bolts, and
washers supplied (See Figure 2-1). Install pulley and
belt then check the following:
a. The motor is mounted so that the motor drive pulley
and sewing machine drive pulley are properlyaligned.
b. The V-belt connecting the motor to the sewing machine
should be tensioned properly. It should be possible to
pull a correctly tensioned belt together between two
fingers within approximately 2 cm (3/4"). Excessive
tension may not only shorten the life of the bearings,
but could also affect the operation of the sewing machine.
A loose belt will affect positioning accuracy.
B. SYNCHRONIZER
1. Install pulley adapter is used (see figure below).
2. Now mount and secure synchronizer to pulley adapter.
3. Mount the synchronizer retaining rod assembly as shown in figure below.
2-1
FIG. 2-1
FIG. 2-2

C. BELT GUARD
After aligning belt and pulleys, install the belt guard (see figure 2-3) starting with the standoff A
and bracket B then add bracket C and belt guard D . Centralize and adjust height and
test for proper clearance.
D. LCD DISPLAY
Mount the LCD display to the motor with the
mounting bracket as shown in figure 2-4.
E. CONTROL BOX
Refer to figure 2-5 and install as follows:
1. Mount primary mounting bracket A to the
top plate of the column B with the two
3/8 screws, washers and lock washers.
2. Fasten L brackets C to control box and
to rear panel plate D with the 10-32
screws provided.
3. Mount On-Off switch and adapter bracket E
as shown.
4. Hook and slide assembly onto bracket A
already fastened to column and screw in
place.
5. Add air control assembly F venturi G
as shown to complete installation.
6. Fasten plastic guard H after power and
cable connections are made.
2-2
ML892E-8
®
Fig. 2-5
FIG. 2-4
FIG. 2-3

2-3
ML892E-9
®
H. MOTOR ROTATION
Temporarily remove the "V" belt. Turn power on then move the pedal forward and note the direction
of motor pulley rotation. If incorrect, do the following:
1. Turn power off.
2. Refer to section IV-C, Hidden Parameters, and follow the instructions to change motor rotation.
The parameter is in the "**** Toggle Switches" group.
3. Install the "V" belt.
G. POWER AND CABLE CONNECTIONS
Refer to figure below and connect all cables as shown. The system can be operated from 230V,
3 phase or 230V, single phase power.
Caution: It is important that the ground wire be connected between the motor and sewing
machine to prevent a static charge buildup at the sewhead.
F. SPEED CONTROL
The Clinton model 892E is equipped with
a remote speed control. Connect treadle rod
to ball joint assembly with rod and drill/tap 2
1/4-20 holes as shown. Assemble with 1/4
screws, flat washer and split washer.
Fig.2-6
Fig. 2-7

SYNCHRONIZER TIMING
Turn the power off before making synchronizer adjustments. Refer to figure below for all adjustments
and perform the steps below to time the synchronizer.
1. Remove cover from synchronizer, then loosen the disc locking screw.
2. Rotate the handwheel so that the needle is at its highest position.
3. Rotate the UP sensor disc until the notch is centered in the photo interrupter module.
4. Rotate the down sensor disc until the notch is centered in the photo interrupter module.
5. Rotate the trim disc until the notch is centered in the photo interrupter module.
6. Tighten the disc locking screw and replace the cover.
NOTE: After power is turned on a fine adjustment may be necessary and can be made by
positioning the needle under power and noting the actual needle UP and needle DOWN
stopping positions. If any of the positions are not correct, readjust the appropriate disc.
3-1
SECTION III
®
ML892E-10

PROGRAMMABLE LCD DISPLAY
A. MAXIMUM SEWING SPEED
Maximum sewing speed can be adjusted by changing the "MAXIMUM SPEED" parameter in the
"LCD" display.
The LCD display, shown below is used to program and set the various parameters of the 892 series,
such as; SPEEDS, TIMERS, COUNTERS, and TOGGLE SWITCHES.
Two (2) different modes of operation are available.
They are:
1. Operating Mode
2. Programming Mode
When power is turned on, the display reads
"OperatingMode".
There are two (2) groups of parameters that are accessed in different ways. They are : (1) parameters
with direct access and (2) hidden parameters with indirect access. In addition a master reset is avail-
able to reset all parameters to their default values.
B. DIRECT ACCESS PARAMETERS
The direct access parameters are divided into four (4) groups. They are (1) SPEEDS, (2) TIMERS,
(3) COUNTERS, and (4) TOGGLE SWITCHES. Table 5-1 describes each parameter, shows
the default value and range of adjustment for each parameter.
4-1
SECTION IV
®
ML892E-11
To change a parameter, follow the sequence described below.
1. Press the key to enter the programming mode. Continue pressing this key until the para-
meter group that is to be changed is displayed. As an alternative; press the key to enter
the programming mode and display the last changed parameter.
2. Press the key to step to the next parameter in the selected group.
3. Press the key to increase or the key to decrease the contents of the displayed para-
meter. Both keys are used to toggle parameters between states in the Toggle Switches group.
Hold the key closed to make the display step automatically.
4. Press the key to return to the operating mode and save the changed parameters.

4-2
®
ML892E-12
TABLE 4-1
PARAMETER DESCRIPTION DEFAULT RANGE
SPEED GROUP RPM RPM
MINIMUM
SLOW STRT
VENT.SPD
First speed when pedal is moved forward.
Initial speed at start of cycle (after trim).
This speed is maintained for No. of stitches set by soft
start count parameter.
Speed motor runs while venturi is active
180
500
2000
80-250
150-1000
100-9000
TIMER GROUP MS MS
STRT DEL
VENT TIME
WASTE REM
CUT TIME
Delays machine start to allow presser foot to drop.
Delays venturi shut off after stop.
Waste removal turned on in the seam when this function
is selected.
Cutter on time or pulse length
120
300
50
80
0-500
10-2500
15-200
10-250
COUNTER GROUP STITCHES STITCHES
SOFTST
FRNT.CNT
END CNT
WASTE REM
Number of stitches sewn at soft start speed after trim
(EOC).
Number of stitches with venturi on and first cut if enabled
after eye is covered.
Number of stitches with venturi on and end cut if enabled
after eye is uncovered.
Number of stitches with venturi on in the seam if the
waste removal function is selected.
3
5
5
50
1-25
1-25
1-25
15-200
TOGGLE SWITCHES
PF/SEAM
PF/EOC
SOFT STRT
HEEL 2
POSITION
Pr. Ft. up or down in seam, treadle neutral.
Pr. Ft. up or down after trim, treadle neutral.
Used to turn soft strt "on" or "off".
If on, needle up. If off footlifter up with heel 2.
Selects the needle position in the seam to UP or DOWN.
DOWN
DOWN
OFF
ENABLED
DOWN
UP/DOWN
UP/DOWN
ON/OFF
ENABLE/DISABLE
UP/DOWN
SWITCHES VENTURI
1ST CUT
2ND CUT
TREADLE
START EYE
SEAMLEN
POS STOP
PF STOP
WASTE REM
Turns chopper on/off after start venturi stitch count.
Turns chopper on/off after the end venturi stitch count.
Neutral: Position before cycle starts
Continue: Cycle starts without releasing treadle
Uncov: Cycle starts independent of eye
Covered: Cycle starts only if eye is covered
No Stop: Turns function off
Stop: Motor stops after stitch count is finished
Select needle position after stop
Select presser foot position after stop
Enables/Disables waste removal function
OFF
OFF
NEUTRAL
UNCOVERED
NO STOP
DOWN
DOWN
DISABLED
ON/OFF
ON/OFF
NEUTRAL/
CONTINUE
COVERED/
UNCOVERED
STOP/NO STOP
UP/DOWN
UP/DOWN
ENABLE/DISABLE

®
ML892E-13
C. HIDDEN PARAMETERS
The parameters in this section are separated from the Direct Access parameters because they are
infrequently changed and should not be changed by the operator. The parameters are listed in:
TABLE 4-2
To enable access to Hidden Parameters, follow the sequence described below.
1. Turn power off, if it is on, then wait until the display goes blank.
2. Press the key and the key simultaneously. Keep pressed then,
3. Turn power on. A series of "***" will appear on the display. They will slowly dissapear.
4. Release the keys then press the key before all the stars dissapear.
5. Press the key repeatedly, until the first hidden parameter group (****SPEEDS) is dis
played.Note that 4 stars (*) as described in section "A".
6. Parameters may then be changed by following the procedure described under
DIRECT ACCESS PARAMETERS (Page 4-1).
4-3
PARAMETER DESCRIPTION DEFAULT RANGE
****SPEEDS RPM RPM
TRIM/POS
MAXIMUM
Machine speed during the position trim cycle.
If *** Tgl switch "position" is set to w/ramp the "trm/pos"
speed affects the slope of the ramp. If "no ramp" is
selected, position speed is constant and can be changed
by the "trim/pos" parameter.
Maximum sewing machine speed. The speed cannot go
higher than 3500 times the pulley ratio.
220
4200
100-400
1000-9900
****MISCELLANEOUS
HYSTERESIS
PF DUTY
The amount the pedal has to be moved when going from
one direction to the other before the speed changes.
Average voltage applied to Pr. Ft. solenoid. The voltage
should be high enough to keep the solenoid energized
without overheating.
3
5
1-10
2-10
****TOGGLE SWITCHES
DIRECTION
POSITION
AUTO MODE
SAFETY SW
SAFETY SW SEW
VENT.SPD
Direction of motor rotation viewed from pulley.
Select position with ramp or position at constant speed.
Maximum speed until eye is uncovered.
Set to enable only on machine with trimmer safety sw. If
enabled, machine will not run unless safety switch is
properly connected.
Defines operation of safety switch. If "CLS" machine
starts only when the switch is closed. If "OPN" machine
starts only when the switch is open.
Enable/Disable function.
CCW
W/ RAMP
DISABLE
DISABLE
CLS
DISABLE
CCW/CW
W/ RAMP
OR NO RAMP
ENABLE/DISABLE
ENABLE/DISABLE
CLS/OPN
ENABLE/DISABLE

4-4
®
ML892E-14
D. MASTER RESET
In some cases it may be necessary to reset all parameters to their default values. This is done as
follows:
1. Turn power off, if it is on, then wait until the display goes blank.
2. Press the key, key and key simultaneously. Keep pressed then,
3. Turn power on. The display alternates between "Push Set" and "For Reset".
4. Push the key within 10 cycles.
5. The word "Programming" is displayed. The parameters will be reset to their default values after
a few seconds.
E. PULLEY RATIO (RATIO BETWEEN MOTOR AND MACHINE PULLEYS)
During the initial setup and after power is first turned on. The pulley ratio must be calculated. The
pedal must be moved forward to do this. While the ratio is being taken, the machine speed is
limited for several stitches. After the ratio is taken, the machine will then accelerate to maximum
speed.
Each time power is turned off then back on, the ratio is checked when the pedal is moved forward
the first time. If the ratio has changed, because of a pulley change, then the ratio will be recalcu-
lated. The ratio can be displayed by pressing the and keys simultaneously. If the ratio is
correct, a star (*) will be displayed after the ratio number.
F. TEST PROGRAM
A test program is available to test the treadle, synchronizer, encoder, and divider for proper
operation. To select the program, press the and keys simultaneously. The display will
show "SYSTEM TEST". Press the key to toggle between each test, i.e. Treadle,
Synchronizer, Encoder, or Divider. Press the key to activate whichever test is selected.
1. Treadle Test
Press the button until "TEST TREADLE" is displayed. Press the button once. The
display should show "NEUTRAL".
a. Move the pedal from neutral to heel 1 then to heel 2. The display should show each positon.

4-5
®
ML892E-15
TEST PROGRAM (Continues....)
b. Move the pedal forward slowly. As the pedal is moved, a number (0 to 255, see NOTE#4)
will be displayed.
This number is proportional to how far the pedal is moved. The lowest number should be no
more than "8" and the highest number greater than "250".
(NOTE: the maximum speed pot should be in the full cw position.)
c. Press the pedal full forward. Turn the maximum speed pot ccw. The displayed count should
decrease as the pot is turned. Return the pot to its maximum cw position.
2. Synchronizer Test
Press the button. The display will read "TEST SYNCHRONIZER". Press the button.
Rotate the machine pulley by hand. The display will show the position. The positions are as
follows: "UP", "DOWN", and "TRIM".
3. Encoder Test
CAUTION: Remove the sewing machine belt. The belt has to be removed because the
motor may not develop suffient torque to turn the machine.
Press the button. The display will read "TEST ENCODER". Press the button. The
display will read "PUSH TREADLE". Press the pedal fully forward for approximately three
seconds then release the treadle. Do not heel. The result will be displayed, either "OK" or
"NOT OK".
Heel the pedal. The display shows the number of counts. The number should be between 795
and 800 pls.
4. Divider Test
NOTE: This test will not function properly if the encoder test fails. Also, remove the sewing
machine belt.
Press the button, the display will read "TEST DIVIDER". Press the button. The
displayreads "PUSH TREADLE". Press the treadle fully forward for 3 seconds, then release
the treadle. If the test works the display will read "DIVIDER OK". If the test fails the display will
show the test which failed, ie. "PASS 1", "PASS 2", "PASS 3", "PASS 4", "PASS 5", or "PASS
6".

5-1
®
CONNECTOR DIAGRAMS
Listed below are the pinouts for the Model 892E control box connectors.
ML892E-16
SECTION V
NO. TOTAL PINS CONNECTOR PIN NO. FUNCTION
1 6 SYNCHRONIZER 1
2
3
4
5
6
+5
DOWN SENSOR
UP SENSOR
TRIM SENSOR
GND
LED
2 6 AUX INPUTS 1
2
3
4
5
6
+5
GND
CHASSIS GND
I 1 SAFETY SWITCH
I 2 INCHING/CHANGE POSITION
I 3
3 4 AUX OUTPUTS 1
2
3
4
+48 V
R1
+48 V
R2
4 2 FOOTLIFT 1
2FOOTLIFT SOL. +48V
5 9 VENTURI, CHOPPER,
AND NEEDLE COOLER 1
4
2
5
3
6
7
8
9
VENTURI SOL. -
VENTURI SOL. +(48V)
CHOPPER SOL. -
CHOPPER SOL. +(48V)
NEEDLE COOLER SOL. -
NEEDLE COOLER SOL. +(48V)
NOT USED
NOT USED
NOT USED

5-2
®
ML892E-17
NO. TOTAL PINS CONNECTOR PIN NO. FUNCTION
8 8 COMMUTATOR 1
2
3
4
5
6
7
8
+5V
ENCODER (S1)
ENCODER (S2)
SIG. GND
PHASE C
PHASE B
PHASE A
-5V
916 LCD DISPLAY 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
EXT1
CHASSIS GND
+5V
GND
D0
D1
D2
D3
D4
D5
D6
D7
CA1
E
ERD
CA0
10 4AC POWER 220V 3 1
2
3
4
PHASE A
PHASE B
PHASE C
CHASSIS GND
1 1 4MOTOR VOLTAGE 1
2
3
4
PHASE A
PHASE B
PHASE C
CHASSIS GND

6-1
®
ML892E-18
SECTION VI
A. MAJOR ASSEMBLIES
DRAWINGS AND PARTS LIST
MODEL 892E
81-0790-02
BELT GUARD*
10-1508-01
LCD DISPLAY
30-4321-01
SWITCH BOX
30-4400-01
WASTE CONTAINER
80-0476-01
FOOTLIFTER**
80-0180-115
* USE 10-1508-02 FOR U.S. 35800DWW
** USE 80-0180-121 FOR EXTENDED COLUMN
USE 80-0180-140 FOR U.S. 36200
MOTOR
81-0731-01
SYNCHRONIZER
81-0733-01
SPEED CONTROL
81-0568-04
CONTROL BOX
81-0737-02
LEXAN GUARD
10-1285-01

ITEM DESCRIPTION PART NO. QUANTITY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
COVER
SCREW
SCREW, S.S.S.
FAN
PC BOARD, ENCODER
SCREW
SPACER
ENCODER DISC
SCREW
ENCODER SENSOR
MOTOR, DC
SCREW, S.S.S.
MOTOR/ENCODER ASSEMBLY
BELT GUARD, FIXED
PULLEY - 50MM
PULLEY - 60MM
PULLEY - 65MM
PULLEY - 70MM
PULLEY - 75MM
PULLEY - 80MM
PULLEY - 85MM
PULLEY - 90MM
PULLEY - 95MM
PULLEY - 100MM
PULLEY - 105MM
PULLEY - 110MM
PULLEY - 115MM
PULLEY - 120MM
PULLEY - 125MM
PULLEY - 130MM
PULLEY - 140MM
PULLEY - 150MM
BELT GUARD, ADJUSTABLE
KEY, PULLEY
SCREW M5 X 10 HEX HD.
BOLT, CARRAIGE
SPACER
WASHER, FLAT
WASHER, SPLIT LOCK
NUT, HEX
HARDWARE KIT, MOTOR MOUNT
PIN
BRACKET, MOTOR MOUNT
SNAP RING
BOLT, ADJUSTING
NUT, HEX
WASHER, SPLIT LOCK
GROMMET
30-4433-01
30-4434-01
30-4435-01
30-4436-01
30-4437-01
30-4438-01
30-4439-01
30-4440-02
30-4441-01
30-4442-01
30-4443-01
30-4444-01
81-0732-01
30-4445-01
30-4204-50
30-4204-60
30-4204-65
30-4204-70
30-4204-75
30-4204-80
30-4204-85
30-4204-90
30-4204-95
30-4204-100
30-4204-105
30-4204-110
30-4204-115
30-4204-120
30-4204-125
30-4204-130
30-4204-140
30-4204-150
30-4203-01
30-4227-01
30-4206-01
30-4298-01
30-4332-01
30-4300-01
30-4301-01
30-4229-01
30-4337-01
30-4219-01
30-4446-01
30-4220-01
30-4205-01
30-4210-01
30-4218-01
30-4472-01
1
3
2
1
1
3
3
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
3
3
3
3
3
1
1
1
1
1
1
1
1
MOTOR ASSEMBLY PARTS LIST, DC SERVO
81-0731-01
6-3
®
ML892E-19-2

E. SYNCHRONIZER
6-6
ITEM DESCRIPTION PART NO. QUANTITY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
SYNCHRONIZER
COVER, SYNCHRONIZER
SCREW M5 X 12 F.H.M.S.
SPACER DISC RETAINING
LED
DISC POSITIONER
SPACER, DISC
DISC, TRIM
SCREW M3.5 X SELF TAP
SPACER
HOUSING
SCREW M4 X 10
SHAFT, SYNCHRONIZER
SCREW M6 X 8 S.S.S.
PC BOARD, SYNCHRONIZER
SCREW, PC BOARD MOUNT
WASHER, SPLIT LOCK
BASE
SCREW M3 X SELF TAP
SCREW M3 X 10
BEARING
81-0733-01
30-4262-02
30-4263-01
30-4264-01
30-4428-01
30-4266-01
30-4267-01
30-4268-01
30-4270-01
30-4271-01
30-4272-02
30-4273-01
30-4429-01
30-4275-01
30-4430-01
30-4209-01
30-4277-01
30-4278-02
30-4279-01
30-4280-01
30-4281-01
1
1
1
1
1
2
3
1
3
1
1
2
1
2
1
4
4
1
2
2
1
®
ML892E-21