Closet Maid PRO GARAGE 10843 User manual

INSTALLATION INSTRUCTIONS
© 2020 ClosetMaid LLC | Ocala, FL 34471 | 1-800-874-0008 | www.closetmaid.com01-18643-00 06/20
Medium Cabinet
10843

2
BEFORE BEGINNING
•Please read all instructions carefully.
•Familiarize yourself with all parts (see“PARTS”) and check quantities.
•Follow all safety precautions (see“SAFETY PRECAUTIONS”).
WARNING
•CHOKING HAZARD FOR SMALL CHILDREN. This unit
contains small parts which could be a choking hazard for
small children. Children should be under adult supervision
at all times or serious injury could occur.
DO NOT OVERLOAD UNIT. If any shelf, top, or bottom
of unit bows or bends, it is overloaded. The shelf, top, or
bottom could collapse and cause serious bodily injury and/
or damage to personal belongings. Evenly distribute loads.
DO NOT CLIMB OR STEP ON THE UNIT. The unit may
become unstable and either tip or collapse. Serious bodily
injury and/or damage to personal belongings may occur.
DO NOT HANG THIS UNIT ON THE WALL. The product
structure is not designed for wall hanging. Serious bodily
injury, damageto personal belongings, and/or damage to
the wall may occur.
DO NOT USE THIS UNIT AS A TELEVISION STAND.
Serious bodily injury and/or damage to personal
belongings mayoccur.
DO NOT STACK UNITS. Stacking of units can cause an
unsafe tip-over hazard which may cause serious bodily
injury and/or damage to personal belongings.
DO NOT MOUNT OR ATTACH ANYTHING TO THE SIDES,
REAR, OR FRONT OF THE UNIT. This can create a force
which can cause the unit to tip. Serious bodily injury and/or
damage to personal belongings may occur.
PROTECT YOUR WORK SURFACE DURING ASSEMBLY.
This can prevent scratching or damage to table tops,
woodfloors, etc.
UNIT DOES NOT PROVIDE PROTECTION AGAINST
ELECTRICAL SHOCK.
SAFETY PRECAUTIONS
STOP FOLLOW INSTRUCTIONS
CAREFULLY
Please do not return product to the retail store.
Forproduct assistance and warranty information
pleasecall Consumer Affairs at 1-800-874-0008.
Manufacturer Warranty
Manufacturer will replace any missing or damaged part
due to manufacturer defect for one year after purchase.
Pleasehave proof of purchase for warranty claims.
• Do not let any sharp objects touch or rub the surface of
theproduct.
• When assembling, do not let children play around the
working area.
• Please confirm all parts are correct before starting the
assembly process.
• DO NOT OVERTIGHTEN. DO NOT USE POWER TOOLS.
Power tools can overtighten screws and strip threads.
We recommend you hand-tighten screws.
Please note location of predrilled holes.

3
Name Qty.
AA
ST6.3 x 12 mm. Screw
28 + 2
BB
Electrical Bushing
1
CC
M6-1.0 x 12 mm. Bolt
4
DD
Key
2
PARTS
Call 1-800-874-0008 for parts and service. For faster service, have the style number ready when calling.
TOOLS REQUIRED
HARDWARE PROVIDED
#3 Phillips Screwdriver 10 mm. Wrench

4
PARTS
Call 1-800-874-0008 for parts and service. For faster service, have the style number ready when calling.
PRODUCT
*Please note location of predrilled holes on each part.
A
B
C
G
D
E
K
L
F
J
I
H
Name Qty Part #
ALeft Side Panel 1 35857
BRight Side Panel 1 35858
CBack Panel 1 35859
DTop Panel 1 35854
EBottom Panel 1 35856
FDoor Frame 1 35865
Name Qty Part #
GCaster without Brake 2 20624
HCaster with Brake 2 20624
IBottom Shelf 1 35860
JInner Shelf 1 35867
KLeft Door 1 35868
LRight Door 1 35869

5
Attach side panels to back panel.
STEP 1
Align both side panels (A & B) with the back panel (C) as shown.
Slide the metal tabs on the back panel (C) into the matching slots on the side panels (A & B). Pull the side panels down
to secure the tabs in place.
*Please note location of predrilled holes on each part.
A
B
C

6
Attach top panel.
STEP 2
*Please note location of predrilled holes on each part.
Align top panel (D) with the top of the unit as shown.
Push in to secure into place. Make sure that all the triangular tabs on the back and side panels completely snap into
place in the square holes on the top panel.
D

7
Attach bottom panel.
STEP 3
*Please note location of predrilled holes on each part.
Align bottom panel (E) with the bottom of the unit as shown.
Push in to secure into place. Make sure that all the triangular tabs on the back and side panels completely snap into
place in the square holes on the bottom panel.
E

8
Attach door frame.
STEP 4
*Please note location of predrilled holes on each part.
Align the door frame (F) with the front of the unit as shown. Please note that the holes on the bottom of the door
frame will match up with the upper holes on the bottom panel.
Use a #3 Phillips screwdriver to secure the door frame to the unit using twelve ST6.3 x 12 mm. screws (AA).
F
x 12
AA
#3 Phillips

9
Attach casters.
STEP 5
*Please note location of predrilled holes on each part.
Align two casters without brakes (G) with the lower holes on the bottom panel (E). Use a #3 Phillips screwdriver to
secure the casters to the unit using eight ST6.3 x 12 mm. screws (AA).
Align two casters with brakes (H) with the upper holes on the bottom panel (E). Use a #3 Phillips screwdriver to
secure the casters to the unit using eight ST6.3 x 12 mm. screws (AA).
G
H
x 16
AA
#3 Phillips

10
Attach shelves.
STEP 6
*Please note location of predrilled holes on each part.
Stand the unit up on the casters.
Place the bottom shelf (I) inside the unit at the bottom. Push down to secure into place, making sure all metal tabs
are connected. Please note that the bottom shelf is larger than the inner shelf and will rest on the lowest three metal
tabs on the back panel.
Determine where you want to position the inner shelf (J). Place the shelf above the tabs on the inner side tracks of
the unit and push down to secure, making sure all metal tabs are connected.
J
I

11
(Optional) Attach unit to workbench top.
STEP 7
*Please note location of predrilled holes on each part.
Note: This step is only if you are planning to attach a workbench top (sold separately). If not, skip to next step.
Place cabinets next to each other and align workbench top with the top of the units. For each cabinet, use a 10 mm.
wrench to attach four M6-1.0 x 12 mm. bolts (CC) through the top panel into the workbench top.
x 8
CC
10 mm.

12
Attach electrical bushing.
STEP 8
*Please note location of predrilled holes on each part.
Align the electrical bushing (BB) with the large circle on the back of the unit. Push in to secure.
x 1
BB

13
Attach doors.
STEP 9
Align the right door (L) with the right side of the unit. Place the bottom lock of the door in the hole on the bottom of
the door frame. Pull the top lock down, align it with the hole on the top of the door frame, and push up to lock into
place. Push the bottom lock down to completely secure the door. Make sure both locks are turned inward toward
the door as shown below. Please note that the right door has the slot for the key lock.
Repeat steps for the left door (K) on the left side of the unit.
Double check that all locks are in position and secure.
*Please note location of predrilled holes on each part.
K
L