CMA Dishmachines CMA-44H Manual

ELECTRICAL
CONNECTION
CMA-44
REAR VIEW
1-2008
CMA-44/66
Quick Setup
Instructions
3
PRESSURE
REGULATOR
OPTIONAL VENT
HOODS 4"X16"
2
STEP
1
STEP
3
STEP
VOLTS  PHASE AMPS
208 1 61
240 1 65
208 3 38
240  3 42
HEATER 10kW 
ELECTRICAL
HARD WIRE
CONNECTION
POINT
3/4" WATER
INLET
2
1/2" WATER
INLET
1
1
DRAIN PIPE
4DETERGENT
FITTING INLET
5MIXING
CHAMBER
5
SCRAP
TRAP DRAIN
4
Connect hot water supply line to rinse 1/2"water
i n l e t . Adjust pressure regulator if necessary. Water
temperature should be 140°F wash and 140°F rinse
for CMA-44L. The CMA-44H should read 155°F wash,
180°F rinse.
Connect fill water supply line (120°F/140°F) to a
3 / 4 " w a t e r i n l e t t o f i l l t h e m a c h i n e .
C o n n e c t d r a i n a t e i t h e r e n d o f t h e h o r i z o n t a l
d r a i n p i p e f r o m w a s h t a n k o r s c r a p t rap drain.
3 Phase: Connect the wire with the highest voltage
(stinger lead) to L2 on the contactor. L1, L2 and L3
must comply with all local and state electrical codes
for sizing of wire and circuit breaker protection.
Additional information can be found in the Installation
and Operation manual supplied with machine.
DRAIN PLUMBING
NOT SUPPLIED
2" HOLE
PLUG
Remove plastic plug to install detergent fitting. Remove
plug from the mixing chamber to install sani/rinse injection
fitting (sanitizer detergent and rinse injection fittings provided
by dispenser manufacturer, CMA does not supply.)
WARNIN G : Electrical and plumbing
connections need to be made by a
licensed service person and comply
with all Federal, State and Local
Health, Electrical, Plumbing and
Safety codes.
800-854-6417
2" HOLE
PLUG
4
STEP
5
STEP
PLUGS
REMOVE
PLASTIC
PLUG AND
INSTALL
DETERGENT
FITTING

8
STEP
Adjust thermostat if necessary. Water temperature
should be 140°F wash and 140°F rinse for CMA44L.
The CMA-44H should read 155°F wash, 180°F rinse.
POWER
OFF-ON
OPERATING
INSTRUCTIONS
CMA-44 FRONT VIEW
1-2008
CMA-44/66
Quick Setup
Instructions
10
STEP
T u r n o n d i s h m a c h i n e b y p r e s s i n g t h e " P O W E R
ON/OFF"switch to the "ON"position. Dishmachine
will fill automatically and will also activate heater.
6
STEP
C l o s e d r a i n v a l v e t o a l l o w m a c h i n e t o f i l l w i t h
water.
9
STEP
C
L
O
S
E
POWER
ON/OFF 10
DETERGENT
PROBE INLET
6
SCRAP TRAP
DRAIN VALVE
9
PRESSURE
GAUGE
TEMPERATURE
GAUGE
Remove the stainless steel plug to install the detergent
probe (provided by dispensermanufacturer, CMA does
not supply).
7
STEP
Remove motor cap to verify motor rotation. Shaft slot
should be rotating clock-wise when motor is running. If
shaft slot is turning counter clock wise, swap L-1 and L-2
on main contactor.
THERMOSTAT
8
MOTOR CAP
7
THERMOSTAT
ACCESS
800-854-6417
WARNIN G : Electrical and plumbing
connections need to be made by a
licensed service person and comply
with all Federal, State and Local
Health, Electrical, Plumbing and
Safety codes.
POWER
OFF-ON