CNS Frame Displays FD-Arena 9972 User manual

1
Your Arena Flat Panel Mount is engineered for easy
assembly. Carefully follow this procedure to prevent any
damage.
Placement and Maintenance
Arena Flat Panel Mount is designed for indoor use on level
floors. Clean steel parts with a moist cloth.
NOTICE: ARENA PERFORMS BEST AGAINST OR NEAR A
WALL.
step 1
Unpack and identify the components at left. The assembly
workspace should be a non-marring surface such as carpet.
step 2
Assemble base
Screw in levelers (N) into C-leg (M). Attach base forks
(O) to C-leg (M) using provided Allen wrench (A), six
(6) 5/16 x 5/8 in screws (b) , and four (4) 5/16 x 1 in
screws (P).
Component list
P
P
P
P
b
b
C - Spine x 1
f - Horizontal Mounting
Bracket
x 1
I - Vertical Mounting
Bracket
x 2
J - TV Mounting Kit
x 1
E - 5/16 x 1 3/4 in
Screws
x 4
D - Swiveling Bracket
Assembly
x 2
g - 5/16 x 3/8 in
Screws
x 4
A - 5mm Allen Wrench
x 1
H - Washer x 4
l - Jam Nut x 2
K - Leveling Disc x 2
P - 5/16 X 1 in
Screws
x 4
N - Levelers x 4
M - C-Leg x 1
O - Base Forks x 1
b - 5/16 x 5/8 in
Screws
x 12
b
N
M
FD-Arena 9972

b
E
step 4
Attach each swiveling bracket Assemby (D) to top
of spine (C) with four (4) provided 5/16” x 1 3/4 in
screws (E) using Allen wrench (A). Be sure to position
each Swiveling Bracket Assembly so that it aligns with
and inserts cleanly into the spine (C) holes.
NOTE: There are several mounting-height positions
to choose from on 3” increments. In general,
for larger TV’s (54” – 60”) select a higher set of
mounting holes, smaller TV’s (40”- 46”) select a
lower set of mounting holes.
front Mount
E
side Mount
step 3
Lower spine (C) onto upright Base Forks/C-Leg assembly
on floor, then fasten securely into place using four (4)
5/16 x 5/8 in screws (b) and provided Allen wrench
(A).
NOTE: Be sure that the side with large openings faces
rearward.

front Mount
g
g
H
H
side Mount
front Mount side Mount
NOTE: Selecting the ‘side-mount’ Spine location for the Swiveling
Brackets will position television close to rear of cabinet, but can
limit left-to-right swiveling. Selecting the ‘front-mount’ Spine
location will position television approx 1.5” closer to cabinet front
and will enable maximum left-to-right swiveling adjustment.
step 5
Attach Horizontal Mounting bracket (f ) to installed
swiveling bracket Assemblies (D) using four (4)
5/16 x 3/8 in screws (g) and four (4) washers (H)
with the provided Allen wrench (A).
NOTE: Slots along Horizontal Mounting Bracket
(F) must be at BOTTOM. Be sure to position each
Swiveling Bracket Assembly (D) so that each sits
within recessed portion of the Horizontal Mounting
Bracket (F). (Circled below)
recommended
2-person step
for easy
installation

K
step 7
With the help of another person, lift television with
installed Vertical Mounting brackets (I) and lower
carefully onto Horizontal Mounting bracket (f ).
step 6
Position each Vertical Mounting bracket (I) on back
of TV and attach using mounting screws and spacers
(if required) provided in TV Mounting Kit (J). Each
bracket must align vertically with the other. Both can be
raised or lowered on back of TV at 1” increments.
Install leveling Disc (K) onto
threaded posts of Vertical
Mounting bracket (I).
Make sure the felt side is
facing out.
NOTE: Various mounting
screws are provided in TV
Mounting Kit (J), but some
TVs may require specific
hardware not provided by
bDI. In such cases, please
contact your TV manufacturer
to identify and source your
hardware.
K x 2
f
I
recommended
2-person step
for safe
installation
J

f
l
I
K
step 7 (continue)
Level the TV using the leveling Discs (K) near the
slots in the lower Horizontal Mounting bracket
(f) . Then secure into place using provided Jam Nut
(l) on exposed mounting stud until finger-tight.
step 8
Use the open channel inside spine (C) to organize
and route cabling to and from the TV.