PARA_DR_EPSU_09/10/04
3
W
E
E
P
N
R
ER
L
M
W
AAA
Trim & Position Buttress Wall Jamb
The Wall Jamb used in this step is shipped with the shower door
unit. Check Wall Jamb for installation holes before trimming.
Trim buttress Wall Jamb (E) to length as per “Spec #1” (see
specification table on page 2). Position it up against the shower
wall and align it 1” from the buttress edge as shown. Hold plumb,
then pencil mark the installation hole locations onto shower wall.
Remove Jamb and lightly center punch the installation hole
locations. Drill1"deepinstallationholesusinga3/16"masonrybit
and insert Plastic Screw Anchors (Y). Reposition Jamb as before
and secure to shower wall using 1-1/4” Installation Screws (W ).
Install Buttress Sill and Glass
TrimbuttressSill(N)tolengthasper“Spec#2”(see specification
table on page 2). Apply a bead of caulking the full length of
underside of buttress Sill. With one end into buttress Wall Jamb,
set Sill atop buttress curb as shown and square it with the curb
edge.
Insert two glass support Setting Blocks (P ) into buttress Sill (refer
topartslist,frontsheet). SettheGlassPanelontheSettingBlocks
and slide glass a 1/2" into buttress Wall Jamb. Hold Glass Panel
inplacebyinstallingshortlengthofPostGlazingvinyl(S)between
Glass Panel and buttress Wall Jamb, both inside and out.
Trim & position Base Sill
Trim base Sill (A) to length as per “Spec #3” (see specification
table on page 2). With weep holes facing toward the interior,
center Sill piece (A) on shower curb. Temporarily tape Sill to curb.
Trim, Assemble & Install Corner Assembly
Trim Corner Assembly pieces (M & AA) to length as per “Spec #4”
(see specification table on page 2). Assemble the Corner Assem-
bly by sliding or snapping pieces (L, AA & M) together as shown in
detailabove. SetCornerAssemblyintobaseSill(A)andslideover
the exposed edge of Glass Panel by 1/2". Hold Corner Assembly
in place by installing short length of Vertical Glazing Vinyl (S )
between Glass Panel and Corner Assembly, both inside and out.
Place Assembly onto buttress Sill, hold plumb, then mark and drill
an installation hole. Secure to buttress wall using one (1) 1-1/4"
installation screw (W).
A
W
E
A
Position Wall Jamb
The Wall Jamb used in this step is shipped with the shower door
unit. Check Wall Jamb for installation holes before installing.
Position Wall Jamb (E) into end of
base Sill and up against the shower
wall. Plumb the Wall Jamb, then
make a pencil mark on the shower
wall thru each of the three (3) instal-
lation holes. Remove Wall Jamb
and lightly center punch the installa-
tion hole locations. Drill 1" deep
installation holes using a 3/16" ma-
sonry bit and insert Plastic Screw
Anchors (Y). Reposition Jamb as
before and secure to shower wall
using three(3) 1-1/4" Installation
Screws (W).
Assemble Header
AssembleHeader by insertingthe Corner Bracket(U) into Header
Pieces (B & C) as shown above. Pull the corner together, then
using the corner bracket’s elongated holes as guides, mark and
drillthe header pieces with a 9/64" drill bit. Loosely secure Corner
Bracket to Header pieces with two #8 x 3/8" machine screws (V).
Pull the corner tightly together, drill the two remaining holes and
secure with two additional screws. Tighten all screws.
B
U
C
