Coastal DKB200 User manual

FITTING INSTRUCTIONS
DKB200 RING DOOR KNOCKER
LIT-FI-DKB200
Page 1 of 6
T01726 871 025 [e-mail] Wcoastal-group.com

FITTING INSTRUCTIONS
DKB200 RING DOOR KNOCKER
LIT-FI-DKB200
Page 2 of 6
T01726 871 025 [e-mail] Wcoastal-group.com
Measure where the
centre line is on the
door.
Confirm at what
height location you
would like Door
Knocker to be
positioned on the
door.
2
Keeping the template
in place on the door,
drill the 2 x 3mm holes,
4mm deep, for the
Anti-spin Pegs.
Note: The holes should
be only 4mm deep.
Then drill 3mm pilot
holes for the Fixing
Bolts all the way
through the door.
Align the centre line
shown on the supplied
Hole Drilling Template
with the centre line of
the door.
Ensure template is
positioned square
and plumb on the
door then fix top and
bottom of template to
door using a
low-tack adhesive
masking tape.
43
1

FITTING INSTRUCTIONS
DKB200 RING DOOR KNOCKER
LIT-FI-DKB200
Page 3 of 6
T01726 871 025 [e-mail] Wcoastal-group.com
HOLE DRILLING
TEMPLATE
CENTRE LINE
NOTE: If printing the template yourself from PDF you will need to ensure you print out at 1:1
scale actual size and that the distance between Fixing Bolts hole centres is 87mm as shown on
this drawing. Measurements shown above are in millimetres.
Hole for Anti-spin Peg
Hole for Fixing Bolts

FITTING INSTRUCTIONS
DKB200 RING DOOR KNOCKER
LIT-FI-DKB200
Page 4 of 6
T01726 871 025 [e-mail] Wcoastal-group.com
Drill the 2 x 9mm holes
for the M8 fixing bolts,
only drilling halfway
through from the front
of the door.
This is so you don’t
split the timber or
cause breakout on the
paint finish.
Affix washer onto end
of bolt on back of
door and secure
the bolt using the
decorative nut.
Hand tighten and
check the Impact
Plate is square on the
outside of the door.
Then tighten the
decorative nut using a
16mm spanner.
Thread the shorter
fixing bolt into the
Impact Plate, turning it
through 3 turns.
Remove decorative
nut and washer from
the 2 x fixing bolts.
Then on the back of
door drill out the 2
x 3mm holes for the
bolts to 9mm, drilling
the rest of the way
through from the back.
Make sure the
Anti-spin Peg is at the
top and thread the
bolt through the door.
Check the Plate is
square on the door
and push in so the peg
on the back enters the
hole drilled for it on
the face of the door.
Measure the thickness of
your door and cut your bolts
to length as follows:
xTop fixing bolt length (for
Knocker) =
Thickness of door + 28mm
xBottom fixing bolt length
(for Impact Plate) =
Thickness of door + 7mm
File the cut end of the Bolt
to give a slight bevel.
5
7
6
8

FITTING INSTRUCTIONS
DKB200 RING DOOR KNOCKER
LIT-FI-DKB200
Page 5 of 6
T01726 871 025 [e-mail] Wcoastal-group.com
Thread the longer
fixing bolt into the
back of the fixing plate
on top of the Door
Knocker, turning it
through 3 turns.
Make sure the
Anti-spin Peg is at the
top and thread the
bolt through the door.
Check the Knocker is
square on the door
and push in so the peg
on the back enters the
hole drilled for it on
the face of the door.
9
Affix washer onto end
of bolt on back of
door and secure
the bolt using the
decorative nut.
Hand tighten and
check the Door
Knocker is square on
the outside of the
door.
Then tighten the
decorative nut using a
16mm spanner.
10

FITTING INSTRUCTIONS
DKB200 RING DOOR KNOCKER
LIT-FI-DKB200
Page 6 of 6
T01726 871 025 [e-mail] Wcoastal-group.com
To help you care for this product please follow the guidelines below.
Immediately after fitting and installation - clean the hardware using a soft cloth and mild soapy
water then dry immediately with a clean, soft cloth.
Please Note
yDO NOT use oily rags or greasy cloths when wiping the product surface.
yDO NOT use bleach, abrasive cleaners, caustic or acid based cleaning materials, or
detergents containing chloride, or any other strong household cleaning products.
yDO NOT use abrasive materials, files or other hard objects against the
product surface.
yThis product should be protected from dust and dirt during any
construction work.
yPVD coatings may fingerprint so we suggest during installation of the product that you
handle it with clean gloves or cloths to guard against stains or fingerprints. Fingerprints
can be removed by washing product with a mild soap and water solution, then dried.
yIf a softer metal such as a ring or a key marks the surface, it is possible some of this metal
may have been left on the PVD coated surface. In this case use a soft cloth and mild,
non-acidic cleaner to remove the soft metal deposit.
If this product has a polished stainless steel or satin stainless steel finish, then our DR121
Stainless Steel Renovation Kit should be used at least every six months to help maintain this
product in pristine condition.
yThe DR121 cleaner is a liquid solution that cleans and
polishes, removing contamination, tarnish, tea staining,
surface rust and on-site dust and dirt without attacking
the metal.
yThis cleaner is essential for keeping hardware cleaned
and maintained especially when fitted to property
situated on or near the coast.
yDR121-CO is a neutral liquid conditioner for use after the
metal surface has been cleaned with DR121-CL cleaner.
yThe conditioner can also be used for daily cleaning and
maintenance of slightly soiled metal surfaces.
Refer to Care and Maintenance Guide for further information
and remember to protect handle during building works.
For more information contact us using the details below.
Hardware Care and Maintenance Guide