Coaster 2734 User manual

2734
NICKEL BRONZE FINISH VANITY SET
ASSEMBLY INSTRUCTION
COASTER FINE FURNITURE
www.coastercompany.com
Page 1 of 4 07/24/2012

ITEM: 2734
A s s e m b l y I n s t r u c t i o n
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy
assembly.
Warning!
1. Don't attempt to repair or modify parts that are broken or defective.Please contact the store
immediately.
2. This product is for home use only and not intended for commercial establishment.
PARTS IDENTIFICATION FOR VANITY :
A. LEFT SIDE FRAME
HARDWARE PACKAGE:
B. RIGHT SIDE FRAME
D. REAR UPPER BAR
E. REAR BOTTOM BAR
F. MIRROR
www.coastercompany.com
1
2
3
4
5
6
7
8
10 PCS
ZDESCRIPTION FIGURE QTY
ALLEN BOLT-LARGE
1 PC
2 PCS
2 PCS
2 PCS
STEP 1
ALLEN KEY
STEP 2
CAP
PLUG
ASSEMBLY INSTRUCTION
G. MIRROR SUPPORT
1 PC
1 PC
1 PC
2 PCS
1 PC
1 PC
2 PCS
Page 2 of 4
BOLT
PLUG 6 PCS
GLASS PAD 8 PCS
A
B
C
D
E
F
G
1
3
7
5
4
45
H. GLASS
2 PCS
D
G
H
H
C. FRONT SIDE FRAME
1
1
1
1
1
1
1
1
1
3
3
3
7
7
7
7
7
7
7
4
5
6
6
ALLEN BOLT-SMALL 4 PCS
2
2
2
2
3
3
A person assembles time for 30 minutes.

A s s e m b l y I n s t r u c t i o n
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy
assembly.
Warning!
1. Don't attempt to repair or modify parts that are broken or defective.Please contact the store
immediately.
2. This product is for home use only and not intended for commercial establishment.
PARTS IDENTIFICATION FOR STOOL : HARDWARE PACKAGE:
ASSEMBLY INSTRUCTION
ITEM: 2734
I. BACK FRAME
J. SIDE FRAME
K. POST 463㎜ - 2 HOLES
www.coastercompany.com
9
10
11
12 PCS
Z DESCRIPTION FIGURE QTY
ALLEN BOLT
SCREW 4 PCS
4 PCS
PLUG
1 PC
2 PCS
1 PC
Page 3 of 4
STEP 3 STEP 4
9
10
L. POST 463㎜ - W/O HOLES
1 PC
M. POST 310㎜
2 PCS
N. CUSHION
1 PC
9
9
9
9
99
9
9
9
9
9
I
J
J
K
L
M
MN
10
10 10
11
11
11 11

Page 4 of 4
ITEM : 2734
Assembly Instruction as below:
Step 1:
Insert the plugs (3) into the left side frame (A) and right side frame (B), and
then fix the side frame (A & B) to the front side frame (C) and rear upper bar
(D) and rear bottom bar (E) with large bolts (1). Insert the glass pad (7) into the
front side frame (C) and rear upper bar (D).
Step 2:
Fix the mirror support (G) to the rear upper bar (D) with the small bolts (2). Fix
the mirror (F) to the mirror support (G) with the caps (5) and bolts (4), and then
insert the plugs (3 & 6) into the end tube of mirror support (G). Place the glass
(H) on the glass pad (7).
Step 3:
Assemble the back frame (I) with side frames (J) using bolts (9). Assemble the
post-2 holes (K) and post-w/o hole (L) on the side frames (J) using bolts (9).
Then, assemble the post-2 holes (M) on the post-2 holes (K) and back frame (I)
using bolts (9). Insert the plugs (11) into the end tube of back frame (I) and
side frames (J).
Step 4:
Screw in the cushion (N) using screws (10) and tighten into place.