Coaster 900374N User manual

Page 1 of 6
900374N
WOOD MANTEL
www.coastercompany.com
ASSEMBLY INSTRUCTION
COASTER FINE FURNITURE
2012/11/30

Page 2 of 6
ITEM:900374N ASSEMBLY INSTRUCTION
www.coastercompany.com
ASSEMBLY TIPS:
• Remove hardware from box and sort by size.
• Please check to see that all hardware and parts are present prior start of assembly.
• Please follow attached instructions in the same sequence as numbered to assure fast &
easy assembly.
• Attach the fireplace insert to the completed wood mantel last. Install insert in from the
back of the fireplace so as not to scratch the hearth/base.
CARE & CLEANING
1. Dust your fireplace regularly with a soft non-lint producing cloth or household dusting
product.
2. You can clean your fireplace with a gentle non-abrasive household cleaner. Make sure
to dry your fireplace immediately with a soft cloth or towel.
Warning!
• DO NOT MOVE MANTEL OR INSERT WHILE PLUGGED INTO POWER
SUPPLY.
• DO NOT SIT ON ANY PART OF THE MANTEL.
Warning!
Use of power tools during assembly of this product may cause damage to the item. It
is NOT recommended to use any type of electric screwdriver in the assembly of this
product.

Page 3 of 6
ITEM:900374N ASSEMBLY INSTRUCTION
www.coastercompany.com
PARTS IDENTIFICATION Z HARDWARE PACKAGE
1PC
1PC
1PC
1PC
1PC
1PC
A: BASE
D:CENTER
FRONT
PANEL
B:LEFT SIDE
CABINET
C:RIGHT SIDE
CABINET
NO
SCP631
36PCS
20PCS
2PCS
2PCS
1PC
BOLT
WOOD DOWEL
FLAT WASHER
Knob (with bolt)
SCREW
TOUCH-UP PEN
2
3
4
5
6
QTYFIGUREDESCRIPTION
E: MANTEL/TOP
F: CENTER
SHELF

Page 4 of 6
ITEM:900374N ASSEMBLY INSTRUCTION
www.coastercompany.com
PARTS IDENTIFICATION PARTS IDENTIFICATION
J: INSERT
SUPPORT
BAR
I: CENTER
BACK
BAR
STEP 1
Locate the Left Side Cabinet (B), Right Side
Cabinet (C), Center Front Panel (D), and set out
face down on a scratch-free surface.
Insert one Wood Dowel (3) into each of the
pre-drilled holes.
Push the Left Side Cabinet (B) and Right Side
Cabinet (C) snug to the Center Front Panel (D).
Make sure the Wood Dowels (3) are seated in
the pre-drilled holes.
Connect the Left Side Cabinet (B), Right Side
Cabinet (C) and Center Front Panel (D) with
connection plate, tighten Screws (5) through the
pre-drilled holes.
STEP 2
Locate Base (A) and set out finished side up on the
floor.
Insert one Wood Dowel (3) into each of the
pre-drilled holes.
Attach the Completed assembly from step 3 to
the Base (A). Make sure that dowels are
seated into the pre-drilled holes in the Base.
Using Bolts (1) and Washers (2) attach panels
through pre-drilled holes in the mounting blocks.
HAND TIGHTEN ONLY.
1PC
1PC
1PC
1PC
G: LEFT UPPER
SIDE PANEL
H: RIGHT UPPER
SIDE PANEL
5
C
B
3
3
1
1
2
2
A
3
3

Page 5 of 6
ITEM:900374N ASSEMBLY INSTRUCTION
www.coastercompany.com
STEP 3
Insert one Wood Dowel (3) into each of the
pre-drilled holes in the top edges of the
Assembly from step 2. Locate Center Shelf (F)
and lay finished side up on top of completed
assembly. From the inside, attach Center Shelf
(F) using Bolts (1) and Washers (2) through the
pre-drilled holes in the mounting blocks.
Attach the Knob (4) to the Right Side Cabinet
(C), use the bolts attached through the
pre-drilled holes in the Right Side Cabinet (C) as
diagram. Then use a Phillips Head Screwdriver
to tighten the bolts.
Repeat with Left Side Cabinet (B)
STEP 5
Insert one Wood Dowel (3) into each of the
pre-drilled holes in the top edges of the
Assembly from step 4. Locate Mantel/Top (E)
and lay finished side up on top of completed
assembly. From the inside, attach Mantel/Top (E)
using Bolts (1) and Washers (2) through the
pre-drilled holes in the mounting blocks.
Using Phillips head screwdriver, tighten all
Bolts alternating top and bottom, left and right.
STEP 6
Rest Center Back Panel (I) into groove on
Mantel Top (E) back edge. Allow the
pre-installed magnets to keep the Center Back
Panel (I) in closed position.
STEP 4
Insert one Wood Dowel (3) into each of the
pre-drilled holes.
Locate the upper side panels (G, H) on the top of
the assembly from step 3, as shown in diagram.
Make sure that dowels are seated into the
pre-drilled holes. Using Bolt (1) and Washer (2)
attach these panels through pre-drilled holes in the
mounting blocks
HAND TIGHTEN ONLY.
1
2
33
F
H
G
4
3
1
2
3
EI
3
3
1
2

Page 6 of 6
ITEM:900374N ASSEMBLY INSTRUCTION
www.coastercompany.com
STEP 7
PLEASE READ ALL “ELECTRIC
FIREPLACE INSERT” INSTRUCTIONS
PRIOR TO INSTALLING ELECTRIC INSERT
IN YOUR COMPLETED FIREPLACE
MANTEL. INSTALL THE INSERT IN
YOUR FIREPLACE CLOSE TO ITS FINAL
POSITION.
Lift insert carefully into the back of the unit and
center in the insert opening. Do not drag insert
across hearth/base as it may scratch the unit.
Connect the Insert Support Bar (J) to the inside
left and right panels, using the bolt (1) and
washer (2) through pre-drilled holes.
MOVE YOUR COMPLETED UNIT ONLY
SHORT DISTANCES. MOVE COMPLETED
UNIT WITH GREAT CARE. IT TAKES TWO
PEOPLE TO MOVE COMPLETED UNIT
INTO ITS FINAL POSITION.
Install
Insert
From
Back
Electric
Fireplace Insert
Completed
Unit
J
12