Coaster Bennington 222715 User manual

ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
Fine Furniture for every stage of life
Chest
222715
PAGE 1 OF 4
REVISION 0 :12/16/2021 COASTERFURNITURE.COM

ASSEMBLY INSTRUCTIONS
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
WARNING!
2. This product is for home use only and not intended for commercial establishments.
ASSEMBLY TIME
A CHEST 1PC
B LEG 4PCS
HARDWARE IDENTIFICATION
1BOLT
(Φ5/16" x 90mm - RBW) 4PCS
2LOCK WASHER
(Φ5/16" - RBW) 4PCS
3FLAT WASHER
(Φ5/16" - RBW) 4PCS
4ALLEN WRENCH
(4MM - RBW) 1PC
COASTERFURNITURE.COM
ITEM:222715
PAGE 2 OF 4
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
PARTS IDENTIFICATION
5 MINUTES

ITEM:222715
ASSEMBLY INSTRUCTIONS
STEP 1
STEP 2
COMPLETE
COASTERFURNITURE.COM
PAGE 3 OF 4
1
2
3
4
A
B

ITEM: 222715
ANTI-TIPPING INSTALLMENT INSTRUCTIONS
FURNITURE TIPPING RESTRAINT
1. Attach one of the mounting brackets securely to the back edge of the furniture. Use the short screw.
2. Determine where the furniture is to be placed and mark location on the wall for the mounting bracket
screw hole approximately 2" below the bracket mounted to the edge of the furniture.
3. Drill a 3/16" hole in the wall. Press the plastic wall plug into the hole and gently tap until the flange on
the wall plug is against the wall surface.
4. Position the bracket over the wall plug and use the long screw to securely attach the bracket to the wall.
5. Place the furniture so the bracket on the back edge is in line with the bracket on the wall.
6. Lace an end of the cable tie down through each bracket. Bring both ends together and slide the
beaded end of the cable tie through the keyhole shaped slot on the other end until snug. Pull down on
the beaded end until it snap locks into the keyhole slot.
7. To double lock return the beaded end back through the keyhole as shown.
8. Check to make sure the cable tie is securely laced and locked to the brackets.
COASTERFURNITURE.COM
PAGE 4 OF 4
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.

10
ITEM: 222715
COASTERFURNITURE.COM
Note: Dimension tolerance ±5%
3.6
32.3
"
8.1"
INNER SIZE OF DRAWER B : 30.5'' X 12.4'' X 5.6''
INNER SIZE OF
H
IDDEN DRAWER : 30.5'' X 12.4'' X 2.2''
INNER SIZE OF DRAWER A : 30.5'' X 12.4'' X 3.5''
18"
40
"
54"
A-
8
-
B
"1.
32.3
"
3.6''