Coaster Edmonton 204353 User manual

COASTERFURNITURE.COM
Fine Furniture for every stage of life
PAGE 1 OF 5
204353
Dresser
ASSEMBLY INSTRUCTIONS
COASTERFURNITURE.COM
Fine Furniture for every stage of life
REVISION 1 : 12/17/2017
REVISION 0 : 02/26/2017
REVISION 2 : 06/04/2019
PAGE 1 OF 5
204393
Dresser
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
COASTER FINE FURNITURE
REVISION 1 : 01/09/2020
REVISION 0 : 02/25/2016

DRESSER
A1PC
COASTERFURNITURE.COM
LEGB 4PCS
C 1PC
CENTER SUPPORT LEG
PAGE 2 OF 5
WARNING !
1 . Don't attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
2 . This product is for home use only and not intended for commercial establishment.
ASSEMBLY INSTRUCTIONS
1 . Remove hardware from box and sort by size.
2 . Please check to see that all hardware and parts are present prior to start of assembly.
3 . Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
ASSEMBLY TIPS:
ASSEMBLY TIME 20 MINUTES
ITEM: 204353
PARTS IDENTIFICATION
HARDWARE IDENTIFICATION
BOLT
(M6 x 60mm - BLK)
1 4PCS
LOCK WASHER
(1/4" - BLK)
2 4PCS
FLAT WASHER
(1/4" x 20mm - BLK)
4PCS
ALLEN WRENCH
(M4 x 65mm - BLK)
4 1PC
3
NOTE:
Philips head screw driver in the assembly process ; however, manufacturer does not provide the item
Change Logo & Ai Format 30/05/2019
CHEST
A
LEGS
B
PAGE 2 OF 5
WARNING !
1 . Don't attempt to repair or modify parts that are broken or defective. Please contact the store
immediately.
2 . This product is for home use only and not intended for commercial establishment.
ASSEMBLY INSTRUCTIONS
1 . Remove hardware from box and sort by size.
2 . Please check to see that all hardware and parts are present prior to start of assembly.
3 . Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
ASSEMBLY TIPS:
PARTS IDENTIFICATION
ASSEMBLY TIME 20 MINUTES
ITEM: 204355
HARDWARE IDENTIFICATION
BOLT
(M6 x30mm - BLK)
1 4PCS
LOCK WASHER
(1/4" - BLK)
2 4PCS
FLAT WASHER
(1/4" x20mm - BLK)
ALLEN WRENCH
(M4 x 65mm - BLK)
4
3
NOTE:
Philips head screw driver in the assembly process ; however, manufacturer does not provide the item

PAGE 3 OF 5 COASTERFURNITURE.COM
ASSEMBLY INSTRUCTIONS
ITEM: 204353
STEP 1
STEP 2
COASTERFURNITURE.COM PAGE 3 OF 5
ASSEMBLY INSTRUCTIONS
ITEM: 204355
STEP 1
STEP 2
4PCS
1PC
A
B
4
1
2
3
B
A
3
1
2
B
4
A
AI
A
B
B
B
B
C
A
C

PAGE 4 OF 5 COASTERFURNITURE.COM
ASSEMBLY INSTRUCTIONS
ITEM: 204353
COMPLETE
STEP 3
PAGE 4 OF 5
COASTERFURNITURE.COM
ASSEMBLY INSTRUCTIONS
ITEM: 204355
COMPLETE
STEP 3
B

WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitle for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.
FURNITURE TIPING RESTRAINT
This tip restraint must be attached to a wall
stud using long screw enclosed.
STEP 1
Attach a bracket securely to the back top rail of the
dresser using short screw provided, through the
smaller hole.
STEP 2
Locate the other bracket on the wall over a wall
stud and two inches below the mounting bracket
secured to the back of dresser. Attached to the wall
stud using the long screw provided, through the
smaller hole.
WALL
STEP 3
Place the dresser into position so both mounting brackets are vertically in line. Lace the end of the
restraint strap through the larger hole in each mounting bracket. Bring both ends together and slide the
flat end through the locking end and draw it through until all slack is removed. Confirm that the strap is
securely laced and locked.
WALL
PAGE 5 OF 5 COASTERFURNITURE.COM
ITEM: 204353
ANTI-TIPPING INSTALLMENT INSTRUCTIONS
WALL
STEP 3
Place the chest into position so both mounting brackets are vertically in line. Lace the end of the restraint
strap through the larger hole in each mounting bracket.Bring both ends together and slide the flat end
through the locking end and draw it through until all slack is removed.Confirm that the strap is securely
laced and locked.
This tip restraint must be attached to a wall
stud using long screw enclosed.
STEP 1
Attach a bracket securely to the back top rail of the
chest using short screw provided,through the smaller
hole.
STEP 2
Locate the other bracket on the wall over a wall
stud and two inches below the mounting bracket
secured to the back of chest.Attached to the wall
stud using the long screw provided,through the
smaller hole.
WALL
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitle for proper adult supervision.
Failure to detach this restraint before moving the furniture may result in injury and damage.
FURNITURE TIPING RESTRAINT
COASTERFURNITURE.COM PAGE 5 OF 5
ITEM: 204355
ANTI-TIPPING INSTALLMENT INSTRUCTIONS

ITEM: 204353
Note: Dimension tolerance ±5%
COASTERFURNITURE.COM
INNER SIZE OF DRAWER : 6.26" X 12.68" X 25.98"
Place the chest into position so both mounting brackets are vertically in line. Lace the end of the restraint
stud and two inches below the mounting bracket
secured to the back of chest.Attached to the wall
COASTERFURNITURE.COM
INNER SIZE OF DRAWER : 5.28" X 12.68" X 29.13"
ITEM: 204355
Note: Dimension tolerance ±5%
33.46"
15.63"
48.03"
29.76"
31.97"
8.00"
59.10"
15.63"
35.91"
30.55"
0.63"
55.35"
11.93"
28.66"
9.45"