Coaster 700882 User manual

COASTERFURNITURE.COM
Fine Furniture for every stage of life
ASSEMBLY INSTRUCTIONS
COASTER FINE FURNITURE
PAGE 1 OF 9
700882
MEDIA TOWER
REVISION 0 : 12/08/2015
REVISION 1 : 09/17/2019

700882
ITEM:
COASTERFURNITURE.COM
PAGE 2 OF 9
ASSEMBLY INSTRUCTIONS
ASSEMBLY TIME
PARTS IDENTIFICATION
60 MINUTES
ASSEMBLY TIPS:
1. Remove hardware from box and sort by size.
2. Please check to see that all hardware and parts are present prior to start of assembly.
3. Please follow attached instructions in the same sequence as numbered to assure fast & easy assembly.
WARNING!
1. Don’t attempt to repair or modify parts that are broken or defective. Please contact the store immediately.
2. This product is for home use only and not intended for commercial establishments.
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
ALEFT SIDE
PANEL 1 PC
BRIGHT SIDE
PANEL 1 PC
CBOTTOM PANEL 1 PC
DCROSS BRACE 2 PCS
ETOP PANEL 1 PC
FADJUSTABLE
SHELF 2 PCS
GUPPER BACK
PANEL 2 PCS
HLOWER BACK
PANEL 1 PC
IDRAWER
FRONT PANEL 2 PCS
JDRAWER BACK
PANEL 2 PCS
KLEFT DRAWER
SIDE PANEL 2 PCS
LRIGHT DRAWER
SIDE PANEL 2 PCS
MDRAWER
BOTTOM PANEL 2 PCS

700882
ITEM:
COASTERFURNITURE.COM
PAGE 3 OF 9
HARDWARE IDENTIFICATION
NOTE:
Phillips head screw driver is required in the assembly process; however, manufacturer does not provide this item.
Z
NO DESCRIPTION FIGURE Q’TY
1GLUE 40g 1 PC
2WOODEN DOWEL
Ø 8x30mm 24 PCS
3CAM BOLT
Ø 7x35.5mm 16 PCS
4CAM LOCK
Ø 15x12mm 16 PCS
5BOLT Ø 9.5x55mm
FOR BOTTOM PANEL
4 PCS
6SCREW Ø 4.3x35mm
FOR DRAWER
8 PCS
7RAIL
L = 250mm DR
DL
CL
CR 2 SET
NO DESCRIPTION FIGURE Q’TY
8SCREW FOR RAIL
Ø 3x12mm 20 PCS
9PIN
Ø 4.9x8mm 8 PCS
10 HANDLE
L=120mm 2 PCS
11 HANDLE BOLT
Ø 4x28mm 4 PCS
12 FOOT
50x50x70mm 4 PCS
13 BOLT Ø 6.35x41mm
FOR FOOT
4 PCS
14 STICKER
Ø 20mm 3 PCS
Z7,Z10,Z11,Z12 not included in blister packaging.

700882
ITEM:
PAGE 4 OF 9 COASTERFURNITURE.COM
(CL)7
(CR)
8
E
D x2
B
7 (CR)
7 (CR)
C
12
13
3
A
7 (CL)
8
2
x 16
8
x 12
3
x 12
x 4
13
x 4
12
7x 2
CL
CR
2
INCORRECT
CORRECT
STEP 1
Apply glue on all wooden dowels to
ensure integrity of the structure.

700882
ITEM:
PAGE 5 OF 9 COASTERFURNITURE.COM
STEP 2
STEP 3
Apply glue on all wooden dowels to
ensure integrity of the structure.
Apply glue on all wooden dowels to
ensure integrity of the structure.
A
D
D
4
1
x 4
4 14
4
14
x 4
4
14
D
G
B
A
4
1

700882
ITEM:
PAGE 6 OF 9 COASTERFURNITURE.COM
5
x 4x 4
4
14
C
H
G
E
B
4
5
1
4
14
STEP 4
STEP 5
Apply glue on all wooden dowels to
ensure integrity of the structure.
Apply glue on all wooden dowels to
ensure integrity of the structure.
L x2 I
J
K
L
M
3 x4
I x2
K x2
2 x8
6 x8
4 x4
10 x2
11 x4
(DR)
7 (DR)
7 (DL)
8
x8

700882
ITEM:
PAGE 7 OF 9 COASTERFURNITURE.COM
STEP 6 STEP 7
9
x 8
9
F
F
AB
I
I

700882
ITEM:
PAGE 8 OF 9 COASTERFURNITURE.COM
Note : Dimension tolerance ±5%
295mm(11.5")
540mm(21.25")
1932mm(76")
302mm(11.75")
302mm(11.75")
333mm(13")
333mm(13")
474mm(18.5")
70mm(2.75")
666mm(26")
666mm(26")
99mm(3.75") 419mm(16.25")
234mm(9")

ANTI-TIPPING INSTALLMENT INSTRUCTIONS
FURNITURE TIPPING RESTRAINT
WARNING
Injury may result from tipping furniture.
This restraint may protect against tipping furniture.
Do not allow children to climb on furniture.
This restraint is not a substitute for proper adult supervision.
Failure to detach this restraint before moving the furniture
may result in injury and damage.
1. To attach the anti-tip strap, securely mount one end to the top of the case piece with
the 5/8” screw.
2. Position the case piece against the wall in the desired location.
3. Pull the anti-tip strap taut and mark the position of where you will secure the other end
on the wall.
4. Drill a 1-1/4” hole in the spot you marked.
5. Tap in plastic wall plug.
6. Fasten anti-tip strap with wall screw provided.
(Please install the anti-tiping kit in the middle of the case piece if only have one set of anti-tipping kit.)
WALL
PAGE 9 OF 9 COASTERFURNITURE.COM