Cobra CHIP700L User manual

1
MODEL: CHIP700L (DR-GS-350H)
COBRA PETROL CHIPPER
OWNER’S MANUAL
IMPORTANT
Read safety rules and instructions carefully before operating equipment.
Cobra Garden Machinery
Henton and Chattell Ltd., London Road, Nottingham NG2 3HW UK
www.cobragarden.co.uk

2
Table of Contents
PART I: General Safety Rules.............................................................................................3
PART II: Familiar with the Wood Chipper............................................................................9
PART III: Operating the Wood Chipper..............................................................................10
PART IV: Maintaining the Wood Chipper...........................................................................12
PART V: Troubleshooting and Parts List ...........................................................................13
PART VI: Warranty and Environment...……………………………………………………….16
PART VII:Assembly Instruction.……….………………………………….…………………..17
Conventions used in this manual
WARNING
This indicates a hazardous situation, which, if not avoided, could result in death or
serious injury.
CAUTION
This indicates a hazardous situation, which, if not avoided, could result in minor or
moderate injury.
NOTICE
This information is important in proper using of your machine. Failure to follow this
instruction could result in damage to your machine or property.
Additional Information and Potential Changes
We reserve the right to discontinue, change, and improve its products at any time
without notice or obligation to the purchaser. The descriptions and specifications
contained in this manual were in effect at printing. Equipment described within this
manual may be optional. Some illustrations may not be applicable to your machine

3
PART I: General Safety Rules
Safety Labels Found on Your Unit

4
Should make sure the emergency stop switch is available before every use. Or may
result in serious injury even death.
WARNING
Read this Safety & Operating Instructions manual before you use the Wood Chipper.
Become familiar with the operation and service recommendations to ensure the
best performance of your machine.
Propose
CAUTION
This machine is designed solely to chip wood and must not be used for any other
purpose.
It should only be used by trained operators who are familiar with the content of this
manual. It is potentially hazardous to fit or use any parts other than your dealer
parts. The company disclaims all liability for the consequences of such use, which
in addition voids the machine warranty.

5
Before using the wood chipper
NOTICE
A．Operators must be fully trained before using this machine.
B．User Manual is read and understood.
C．Machine is positioned on level ground, all guards are fitted and in good
condition.
D．Blades are in good condition and secure. All blades are sharpened or replaced
in sets.
E．All fasteners are checked for tightness.
F．Only WOODEN materials free of nails etc. are fed into the machine.
G．Emergency stop wire is rightly connected and the switch is functional.
H．Fire extinguisher is available on site.
When using the wood chipper
NOTICE
A. Always feed from the side.
B. It is better to have a second trained operator within easy reach of the machine.
C. Maintain strict discipline at all times and service machine at specified periods.
D. Note direction of discharge chute and if necessary note the wind direction to
prevent debris from being blown into highway or where it could affect members
of the public.
E. DO NOT put any part of your body into the in-feed chute while the machine is
running.
F. DO NOT operate the machine whilst under the influence of alcohol or drugs.
G. DO NOT operate inside a building or confined space or Climb on the in-feed
chute.
Protecting Yourself and Those Around You
WARNING
This is a high-powered machine, with moving parts operating with high energy. You
must operate the machine safely. Unsafe operation can create a number of hazards
for you, as well as anyone else in the nearby area. Always take the following
precautions when using this machine:
A. Keep in mind that the operator or user is responsible for accidents or hazards
occurring to other people, their property, and themselves.
B. Always wear protective goggles or safety glasses with side shields while using
the Wood Chipper to protect your eyes from possible thrown debris.
C. Avoid wearing loose clothing or jewelry, which can catch on moving parts.
D. We recommend wearing gloves while using the Wood Chipper. Be sure your
gloves fit properly and do not have loose cuffs or drawstrings.
E. Wear shoes with non-slip treads when using your Wood Chipper. If you have

6
safety shoes, we recommend wearing them. Do not use the machine while
barefoot or wearing open sandals.
F. Wear long trousers while operating the Wood Chipper.
G. Keep bystanders at least 50 feet away from your work area at all times. Stop the
engine when another person or pet approaches.
Safety for Children and Pets
WARNING
Tragic accidents can occur if the operator is not alert to the presence of children
and pets. Children are often attracted to the machine and the chipping activity.
Never assume that children will remain where you last saw them. Always follow
these precautions:
A. Keep children and pets at least 50 feet from the working area and ensure they
are under the watchful care of a responsible adult.
B. Be alert and turn the machine off if children or pets enter the work area.
C. Never allow children to operate the Wood Chipper.
Safety with Petrol - Powered Machines
WARNING
Petrol is a highly flammable liquid. Petrol also gives off flammable vapor that can
be easily ignited and cause a fire or explosion. Never overlook the hazards of petrol.
Always follow these precautions:
A. Never run the engine in an enclosed area or without proper ventilation as the
exhaust from the engine contains carbon monoxide, which is an odorless,
tasteless, and a deadly poisonous gas.
B. Store all fuel and oil in containers specifically designed and approved for this
purpose and keep away from heat and open flame, and out of the reach of
children.
C. Replace rubber fuel lines and grommets when worn or damaged and after 5
years of use.
D. Fill the petrol tank outdoors with the engine off and allow the engine to cool
completely. Don't handle petrol if you or anyone nearby is smoking, or if you're
near anything that could cause it to ignite or explode. Reinstall the fuel tank
cap and fuel container cap securely.
E. If you spill petrol, do not attempt to start the engine. Move the machine away
from the area of the spill and avoid creating any source of ignition until the gas
vapors have dissipated. Wipe up any spilled fuel to prevent a fire hazard and
properly dispose of the waste.
F. Allow the engine to cool completely before storing in any enclosure. Never
store a machine that has petrol in the tank, or a fuel container, near an open
flame or spark such as a water heater, space heater, clothes dryer or furnace.

7
G. Never make adjustments or repairs with the engine running. Shut down the
engine, disconnect the spark plug wire, keeping it away from the spark plug to
prevent accidental starting, wait 5 minutes before making adjustments or
repairs.
H. Never tamper with the engine’s governor setting. The governor controls the
maximum safe operation speed and protects the engine. Over-speeding the
engine is dangerous and will cause damage to the engine and to the other
moving parts of the machine. If required, see your authorized dealer for engine
governor adjustments.
I. Keep combustible substances away from the engine when it is hot.
J. Never cover the machine while the muffler is still hot.
K. Do not operate the engine with the air cleaner or the carburetor air intake cover
removed. Removal of such parts could create a fire hazard. Do not use
flammable solutions to clean the air filter.
L. The muffler and engine become very hot and can cause a severe burn; do not
touch.
General Safety
WARNING
Operating this Wood Chipper safely is necessary to prevent or minimize the risk of
death or serious injury. Unsafe operation can create a number of hazards for you.
Always take the following precautions when operating:
A. Your Wood Chipper is a powerful tool, not a plaything. Exercise extreme
caution at all times. The machine is designed to Chip Woods. Do not use it for
any other purpose.
B. Know how to stop the Wood Chipper quickly.
C. Never operate your unit on a slippery, wet, muddy, or icy surface. Exercise
caution to avoid slipping or falling.
D. See manufacturer’s instructions for proper operation and installation of
accessories.
E. Never use the machine without ensuring that all guards and shields are in
place.
F. Never, under any conditions, remove, bend, cut, fit, weld, or otherwise alter
standard parts on the Wood Chipper. This includes all shields and guards.
Modifications to your machine could cause personal injuries and property
damage and will invalid your warranty.
G. If the machine start to make an unusual noise or vibrate, shut down the engine,
disconnect the spark plug wire, keeping it away from the spark plug to prevent
accidental starting, wait 5 minutes for engine to cool down, then inspect for
damage. Vibration is generally a warning of trouble. Check damaged parts and
clean, repair and/or replace as necessary.

8
H. Never tamper with safety devices. Check their proper operation regularly.
I. Before performing any maintenance or inspection procedure, shut down the
engine, disconnect the spark plug wire keeping it away from the spark plug to
prevent accidental starting, wait 5 minutes for machine to cool down.
J. Never allow people who are unfamiliar with these instructions to use the Wood
Chipper. Allow only responsible individuals who are familiar with these rules of
safe operation to use your machine.
K. Never overload or attempt to chip woods beyond the manufacturer’s
recommendation. It could result in personal injury or damage to the machine.
L. While using, don't hurry or take things for granted. When in doubt about the
equipment or your surroundings stop the machine and take time to look things
over.
M. Never operate the machine when under the influence of alcohol, drugs, or
medication.
N. Use the machine only in daylight.
O. Stay alert for hidden hazards or traffic.
P. Keep all nuts and bolts tight and keep the equipment in good operating
condition.
A Note to All Users
List of warnings and cautions cannot be all-inclusive. If situations occur that are
not covered by this manual, the operator must apply common sense and operate
this WOOD CHIPPER in a safe manner. Contact the dealers for assistance in your
area.

Part II: Familiar with the Wood Chipper
9
PART II: Familiar with the Wood
Chipper
It may be helpful to familiarize yourself with the controls and features of the Wood
Chipper. If you have any question, please contact the dealers in your area.
TECHNICAL SPECIFICATIONS
Recoil Start / Electric Start
Engine
7HP four strokes
Power
Petrol
Chipper Capacity
3CBM/hour to 5CBM/hour
Wood Diameter
diameter 100mm
Chipper Blade
twin reversible blades
Overall Height
1150mm
Overall Length
1850mm
Width
740mm
weight
145kgs
Roller Max RPM
2000rpm
Sound Power Level
118db

Part III: Operating the Wood Chipper
10
PART III: Operating the Wood Chipper
Familiarize yourself with the features of your Wood Chipper before beginning the
steps outlined in this chapter.
WARNING
A. Read and understand all instructions, safety precautions, and/or warnings
listed in “PART I: General Safety Rules” before operating the WOOD CHIPPER.
If any doubt or question arises about the correct or safe method of performing
anything found in this manual, please contact the dealers in your area.
B. When operating the Wood Chipper, make sure you are standing in the safe
operating area (OPERATOR ZONE). You must stay in the safe operating area at
all times when the ram is in motion (whether extending or retracting). Never
place any part of your body into a position that causes an unsafe operating
condition.
C. Before loading and operating the Wood Chipper, always wear protective gear,
including safety goggles, hearing protection, tight-fitting gloves without draw
strings or loose cuffs, and steel-toed shoes.
D. Knowing the correct and incorrect methods of Chipping woods. Never using an
incorrect or unsafe method.
Starting
1. Position your Wood Chipper on flat, dry ground, make sure the machine cannot
be moved.
2. Always check the oil level before starting and top up as needed.
3. Make sure the fuel shut-off valve is in the “ON” position.
4. Move the choke control lever to the “CHOKE” position (should only be needed
if the engine is cold).
5. Move the throttle control lever to the “FAST” position.
6. Recoil Start: Turn the Ignition Switch to the “On” position. Grasp the recoil
starter handle and slowly pull until you feel resistance. Let the cord retract a
little bit then pull the cord rapidly to start the engine. One or two pulls usually
starts the engine.
7. Electric Start (where fitted): Turn and hold the Key in the start position until
Engine starts then let the Key return to run position.
8. Move the choke control lever (if used for cold engine) slowly back to the “RUN”
position when the engine is running well.
9. If the Wood Chipper has not been running (cold engine), warm up the engine by
running the engine at half throttle for 3 to 4 minutes, then advance the engine
throttle control to the maximum speed.

Part III: Operating the Wood Chipper
11
Stopping
1. Move the Throttle Lever to IDLE.
2. Recoil Start: Turn the Ignition Switch to the OFF position.
3. Electric Start: Turn the Key to the OFF position.
Operator Zone
Wood Chipping
NOTICE
Woods’ and branches’ diameter should be no bigger than 120mm.
WARNING
Do not place your hands into the chute when loading. This is a very UNSAFE
method and could result in injury to your hands.
Do not reach or step across the rail while the Wood Chipper is running. This is a
very UNSAFE method which could cause personal injury, even death.
When Blocked
If the Roller stops while chipping woods or branches, the engine should be stopped,
and take out the woods which stuck the roller, and then restart the engine, and chip
again.

Part IV: Maintaining The Wood Chipper
12
PART IV: Maintaining the Wood Chipper
Regular maintenance is the way to ensure the best performance and long life of
your machine. Please refer to this manual and the engine manufacturer's user
manual for maintenance procedures.
WARNING
Before performing any maintenance procedure or inspection, stop the engine, wait
five minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it
away from the spark plug. Disconnect the Battery Terminals (Electric start only).
Regular Maintenance Checklist
Procedure
Before Each
Use
Every 3
Hours
Every 25
Hours
Every
100
Hours
Check engine oil level
Δ
Check general equipment
condition
Δ
Check wedge for
sharpness
Δ
Check belts
Δ
Check tire pressure
Δ
Clean engine exterior and
cooling
Δ
Change Engine Oil
First time
5hours
Δ
Replace air filter
Δ
Replace spark plug
Δ
Engine Service
Refer to the engine manufacturer’s user manual for engine maintenance. Check
before use.
Lubrication
NOTICE
All Bearings of your Chipper are sealed units and should have sufficient lubricant
to last the life of your machine with normal use.

13
PART V: Troubleshooting and Parts List
Most problems are easy to fix. Consult the Troubleshooting Table below for
common problems and their solutions. If you continue to experience problems,
contact the dealers in your area.
WARNING
Before performing any maintenance procedure or inspection, stop the engine, wait
five minutes to allow all parts to cool. Disconnect the spark plug wire, keeping it
away from the spark plug.
Troubleshooting Table
SYMPTOM
POSSIBLE CAUSE
The engine won’t start.
(Please refer to the
engine user manual
for engine-specific
procedures.)
Is the ignition switch in the “ON” position?
Is the fuel shut-off valve on?
Are you using fresh, clean petrol? If the petrol is old, change
it. Use a fuel stabilizer if you keep petrol longer than 30 days.
Is the spark plug clean? If the spark plug is dirty or cracked,
change it. If it’s oily, leave it out, hold a rag over the plug hole
and pull the recoil cord several times to blow out any oil in the
cylinder, then wipe off the plug and reinsert it.
The engine lacks
power
or is not running
smoothly.
(Please refer to the
engine user manual
for engine-specific
procedures.)
Check that the Throttle Lever is in the “Run” position.
Is the air filter clean? If it’s dirty, change it following the
procedure in the engine manufacturer’s owner’s manual.
Is the spark plug clean? If it’s fouled or cracked, change it. If
it’s oily, leave it out, hold a rag over the plug hole and pull
your recoil cord several times to blow out any oil in the
cylinder, then wipe off the plug and reinsert it.
Are you using fresh, clean unleaded petrol? If it’s old,
change it. Use a fuel stabilizer if you keep petrol longer than
30 days.
Does your engine have the right amount of clean oil? If it’s
dirty, change it following the procedure in the engine
manufacturer’s owner’s manual.
Check the oil level and adjust as needed.
Engine smokes.
(Please refer to the
engine user manual
for engine-specific
procedures.)
Check the oil level and adjust as needed.
Check the air filter and clean or replace if needed.
You may be using the wrong oil—too light for the
temperature. Refer to your Engine Owner’s Manual for
detailed information.
Clean the cooling fins if they’re dirty.
Not running with full
chipping power.
The belts may be too loose and slipping. Adjust or replace
belts as need.

14
Explosion View and parts list
Ref.No
.
Description
Ref.No
.
Description
1
Belt cover
33
Anvil spacing bar
2
Belt
34
Battery box
3
Drive Pulley
35
Battery
4
Drum pulley
36
Bearing cover
5
Spacer
37
Blade
6
Bearing
38
Anvil
7
Seal plate
39
Battery fasten board
8
Inner belt cover
40
Bearing hole cover
9
Washer 8
41
flange
10
Engine
42
Bearing
11
Infeed hopper
43
Bearing seal
12
Press switch fixaton
44
Wheel
13
Press switch
45
Drum
14
Handle
46
space
15
Fitting pipe
47
Wheel axle
16
Emergency stop frame
48
Battery base plate
17
Extension pipe
49
Arch board
18
M10 lock nut
50
Forefoot
19
M10 nut
51
Discharge damping rubber
20
Compression spring
52
Tow bar
21
Infeed extension
53
Foot rubber
22
Rubber layering
54
Tow hitch
23
Rubber
55
Discharge bottom part
24
Restore handle
56
Discharge top part
25
Kill switch
57
Chute adjust
26
Switch cover
27
Extension spring
28
Gear plate
29
Engine fixation plate
30
Shock cushion holds plastic
clasp
31
Infeed damping pad
32
Main frame

15

16
PART VI: Warranty & Environment
This product is warranted in accordance with legal regulations for a 24 month period effective
from the date of purchase by the first user.
This product will not be covered if used in a commercial application.
This warranty covers all material or production failures, it does not include: defects from normal
wear and tear, parts such as, bearings, brushes, cables, air cleaning elements, brake pad,
clutch disc, tyre, wheel, recoil starter rope, belts, cutter blades, plugs, lubricant oils and grease
or accessories. Damage or defects resulting from abuse, accidents or alterations, natural fading
of painted or plated surfaces, sheet peeling and other natural deterioration.
Any damage that occurs from the use of non-genuine Cobra parts will not be covered.
We reserve the right to reject any claim where the purchase cannot be verified or when it is
clear that the product was not maintained properly. (Clean ventilation slots, carbon brushes and
serviced regularly)
Expenses incidental to the warranty claim that are not covered;
-Compensation for loss of time, commercial loss or rental costs of substitute product.
-Costs incurred for transportation to and from the dealership.
Any damage that occurs from the following will not be covered; exposure of the product to
smoke and soot, chemical agents, bird droppings or other animal waste, seawater, sea breeze,
salt or other environmental phenomena.
Any damage resulting from operating methods other than those indicated in the owner’s manual
will not be covered.
Your purchase receipt must be kept as proof for date of purchase. Your un-dismantled product
must be returned to your dealer in an acceptably clean state, accompanied by your proof of
purchase.
ENVIRONMENT
Should your machine need replacement after extended use, do not put it in the domestic waste
but dispose of it in an environmentally safe way.

17
PART VII: Assembly Instructions
1. Remove from packing & fitting the wheel axle.
Use a block to support whilst securing and fitting the
axle for the transport wheels.
2. Wheel split pins fitting.
Fit with split pins just tight enough to get split pins in.
3. Fit the intake hopper
Fit the intake hopper and secure the bolts.
4. Fit the front resting plate.
Secure the front support with the bolts provided.
5. Fit the exit/discharge shoot
The shoot is fitted with 4 bolts –ensure these are fully
tightened and secure.

18
6. Fit the tow bar to the front
resting plate with the bolts
provided, fully tighten and
ensure securely fitted.
7. Install the intake extension chute and intake
extension bar
8.Attach the emergency stop wire.
Before operating fit the emergency stop wire. Check the
engine stops correctly before operating in every case.
Add engine oil as per the engine manufacturers instructions. The engine is
shipped without oil.

19
EC-DECLARATION OF CONFORMITY
EC Declaration of Conformity
We herewith declare,
Cobra Garden Machinery
Henton & Chattell Ltd, London Road, Nottingham NG2
3HW United Kingdom
That the following machine complies with the appropriate basic safety and health requirements
of the EC Directive based on its design and type, as brought into circulation by us.
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity
Machine Description:
Petrol Wood Chipper
Machine Type:
CHIP700L (DR-GS-350H)
Displacement
212cm³
Max. Operating Width:
100mm
Measured sound power level:
110dB(A)
Guaranteed sound power level:
118dB(A)
Notified Body for EC Directive
2000/14/EC Annex V & 2005/88/EC
SGS-CSTC Standards Technical Services (Shanghai)
No.588 West Jindu Road, SongJiang District,
Shanghai, China
Applicable EC Directives:
2006/42/EC 2014/30/EU
2000/14/EC 97/68/EC
Applicable Harmonized Standards:
EN ISO 12100:2010
EN 13683:2003+A2:2011+AC:2013
EN ISO 14120:2015
EN ISO 13857:2008
EN ISO 14982:2009
Authorized Signature/Date/ Place:
Peter J. Chaloner 11/4/2022
Title of Signatory:
Managing Director
Name and address of the person
authorised to compile the technical
file
Cobra Garden Machinery
Henton & Chattell Ltd, London Road, Nottingham NG2
3HW United Kingdom