Cobra 14 BAND XRS 9470 User manual

XRS 9470
14 BAND™
HIGH-PERFORMANCE
DIGITAL RADAR/LASER
DETECTOR WITH XTREME RANGE
SUPERHETERODYNE®TECHNOLOGY
Nothing Comes Close to a Cobra® English
Operating Instructions
Printed in China
Part No. 480-663-P
Version B

Important Information and
Customer Assistance
Introduction
English
Important Information •
Federal Laws Governing the Use of Radar Detectors
It is not against federal law to receive radar transmissions with your Cobra radar/
laser detector. The Communications Act of 1924 guarantees your right to receive
radio transmissions on any frequency. Local laws that contravene this Act, while
illegal, may be enforced by your local law enforcement officials until and unless
they are prohibited from doing so by federal court action.
Safety Alert
Use of this product is not intended to, and does not, ensure that motorists or
passengers will not be involved in traffic accidents. It is only intended to alert
the motorist that an emergency vehicle equipped with a Cobra Safety Alert
transmitter is within range as defined by that product. Please call local fire
and police departments to learn if coverage exists in your area.
Safe Driving
Motorists, as well as operators of emergency or service vehicles, are expected to
exercise all due caution while using this product, and to obey all applicable traffic laws.
Security of Your Vehicle
Before leaving your vehicle, always remember to conceal your radar detector
in order to reduce the possibility of break-in and theft.
Customer Assistance •
Should you encounter any problems with this product, or not understand its many features,
please refer to this owner’s manual. If you require further assistance after reading this
manual, Cobra Electronics offers the following customer assistance services:
For Assistance in the U.S.A.
Automated Help Desk English only. 24 hours a day, 7 days a week 773-889-3087 (phone).
Customer Assistance Operators English and Spanish. 8:00 a.m. to 5:30 p.m. Central Time
Mon. through Fri. (except holidays) 773-889-3087 (phone).
Questions English and Spanish. Faxes can be received at 773-622-2269 (fax).
Technical Assistance English only. www.cobra.com (on-line: Frequently Asked
Questions). English and Spanish. [email protected] (e-mail).
For Assistance Outside the U.S.A.
Contact Your Local Dealer
©2010 Cobra Electronics Corporation
6500 West Cortland Street
Chicago, Illinois 60707 USA
www.cobra.com
Customer Assistance
A1

Controls, Indicators
and Connections
Introduction
A2 English
Controls, Indicators and Connections •
12V DC
Power Jack
On-Off/Volume Control
Allows you to adjust the
volume of the tone alerts.
Dim Button
Allows you to adjust the UltraBright
Data Display brightness for easy
reading. (Also turns VG-2 and
Spectre I & IV+ alerts On and Off.*)
LaserEye
For 360° detection
of laser signals.
Windshield Bracket
Release Button
IntelliMute Button
Engine RPM sensing mute function
which reduces false alerts. Button
turns IntelliMute On and Off. (Also
enters IntelliMute setting mode.*)
Mute Button
For manual mute or auto
mute of audio alerts. (Also
turns Voice Alert On and Off.*)
* Press and hold for four seconds to
access these functions.
WARNING
Modifications or parts substitutions not approved
by Cobra Electronics Corporation may violate
FCC Rules and void your authority to operate
this equipment.
Speaker
City Button
For City or Highway
modes to reduce false
alerts. (Also turns Ku
alerts On and Off.*)
Windshield
Bracket
Mount
Audio Jack

This booklet describes the simple steps for mounting and setting up your detector. It also provides helpful
information about how radar and laser guns are used and how you can interpret the alerts you receive.
Display and Product Features
Introduction
Nothing Comes Close to a Cobra®A3
Display •
X K Ka VS c
XKKa V S c
X K Ka VS c
NOTE: In This Manual
When steady,
the display will
be shown:
When blinking,
the display will
be shown:
X & K will light
simultaneously
when indicating
Ku detection:
Xtreme Range
Superheterodyne®Technology
With super-fast sweep circuitry,
XRS provides extra detection range
and the best possible advance warning
to even the fastest radar guns
Detection and Separate Alerts For:
Radar signals (X, K, Ka and Ku bands,
with signal strength indicated), Laser
signals, Safety Alert signals, VG-2
signals, Spectre I & IV+ signals
LaserEye®
For 360° detection of laser signals
Instant-On Ready
Detects radar guns with “instant-on”
(very fast) speed monitoring capabilities
Pop Detection
Detects the latest super-fast instant-on
single pulse radar guns
Tone Alert or Voice Alert®
With adjustable volume
UltraBright™ Data Display
Easy-to-read with adjustable brightness
City or Highway
Modes to reduce false alerts
Alert Programming
Easy setting of radar bands to be monitored
Safety Alert®
Traffic warning system distinguishes
important safety alerts from other
K band signals
Manual Mute or Auto Mute
A mute function of audio alerts
IntelliMute®
A mute function reduces false audio alerts
by sensing engine RPMs
IntelliMute®Pro
Prevents detection by radar detector detectors
(RDDs) when traveling at slower speeds
Mounting
Mounts easily on windshield or dashboard
Product Features
IntelliMute
Indicator
Radar, VG-2,
Spectre I & IV+ and
Safety Indicators
X K Ka V S L
Signal
Strength,
Pop, Laser,
City/Highway
and IntelliMute Pro
Mode Indicators
Signal Strength 1 (weakest) to 5 (strongest)

Nothing Comes Close to a Cobra®1
Contents
Introduction
Introduction
Important Information ............................................................................... A1
Customer Assistance ................................................................................. A1
Controls, Indicators and Connections........................................................ A2
Display....................................................................................................... A3
Product Features........................................................................................ A3
Your Detector
Installation ................................................................................................... 2
Getting Started............................................................................................. 5
Auxiliary Audio Jack ................................................................................. 5
Settings........................................................................................................ 6
Highway/City Mode................................................................................... 6
UltraBright Data Display Brightness ......................................................... 7
Muting an Alert......................................................................................... 8
Auto Mute Mode....................................................................................... 8
IntelliMute................................................................................................. 9
IntelliMute Pro......................................................................................... 12
Voice/Tone Setting .................................................................................. 13
VG-2 and Spectre I & IV+ Alert Settings ................................................. 13
Radar Alert and Pop Alert Settings...........................................................14
Detection..................................................................................................... 15
Signals Detected...................................................................................... 15
Audio Alerts............................................................................................. 15
Visual Display.......................................................................................... 15
Instant-On Detection................................................................................ 18
Responding to Alerts............................................................................... 18
Understanding Radar and Laser ................................................................. 19
Maintenance................................................................................................ 20
Specifications.............................................................................................. 21
Warranty
Limited 1-Year Warranty............................................................................. 22
Customer Assistance
Product Service .......................................................................................... 23
Optional Accessories .................................................................................. 24
Accessories Order Info ............................................................................... 25
Trademark Acknowledgement..................................................................... 25

Installation
Your Detector
2English
Installation •
Where to Mount Your Unit
You will get optimum performance from your detector if you Mount it at a
point approximately in the center of the vehicle, as low as possible on the
front windshield without obstructing the unit’s view of the road either to
the front or rear. Make sure the unit is level with the road. You can also
mount it directly on the dashboard.
The unit’s lens must not be blocked and the LaserEye should have a clear
view out the back window to allow 360° detection.
Radar and laser
signals pass
through glass but
not through other
materials and
objects. Objects
that can block or
weaken incoming signals include:
JWindshield wiper blades
JMirrored sun screens
JDark tinting at the top of the windshield
JHeated windshields currently available on some vehicles
(Instaclear for Ford, Electriclear for GM.) Consult your dealer
to see if you have this option.
The LaserEye Should Have a Clear View
Windshield Mounting Dashboard Mounting

Nothing Comes Close to a Cobra®
Your Detector
3
1. Attach the rubber
cups to the bracket.
2. Make sure the rubber cups and your windshield are clean.
3. Push the bracket firmly
onto the windshield.
4. Attach the detector to
the bracket. Check the
angle of the unit.
5. To adjust the angle if
necessary, gently push or
pull on the bracket to bend
it. DO NOT use the detector
to bend the bracket.
6. Plug the power cord
into the detector.
7. Plug the cigarette lighter
adapter on the power
cord into your vehicle’s
cigarette lighter.
8. You can temporarily remove the detector whenever you
wish by pressing the bracket release button and sliding
it off the bracket.
Windshield Mounting
Installation

Installation
Your Detector
4English
1. Place the detector on the dashboard to find a location
where the unit has a clear, level view of the road.
The angle can NOT be adjusted after mounting.
2. Remove the paper backing
from one side of the hook-
and-loop fastener.
3. Attach the pad to the
dashboard at your chosen
location and remove the
other paper backing.
4. Attach the detector to the
hook-and-loop fastener.
You can remove and
reattach the unit as
often as you like.
5. Plug the power cord
into the detector.
6. Plug the cigarette lighter
adapter on the power
cord into your vehicle’s
cigarette lighter.
Dashboard Mounting

Getting Started •
Getting Started
Your Detector
Nothing Comes Close to a Cobra®
Power On
X K Ka V S h
To Turn On the Unit and Adjust the Audio Volume
Rotate the On-Off/
Volume control
clockwise (away
from you).
Tone Voice Visual Display
Three beeps Testing, then
three beeps
System Ready, then
Voice Alert
happears in the
display indicating
that the power
is On
On-Off/
Volume Control
Rotate clockwise
(away from you)
NOTE
In some vehicles, power is supplied to the cigarette lighter even while the ignition
is Off. If this is the case with your vehicle, you should turn Off or unplug your
detector when parking for lengthy periods.
Auxiliary Audio Jack •
The Auxiliary Audio Jack can be used to connect external speakers in
environments with high ambient noise levels. The internal speaker will
be disconnected. (This uses a mini stereo audio connector.)
Auxiliary
Audio Jack
5

Press and
release
Settings
Your Detector
6English
Highway/City Mode
Setting your detector to City mode delays all X band audio alerts until
the signal strength reaches Level 3. (A single beep will sound when the
signal is first detected.) This will reduce false alerts while you are driving
in, or near, urban areas where there are many sources for conflicting
X band signals such as microwave towers and automatic door openers.
To change settings, follow the procedure listed below, which indicates
what you will see and hear (either in Voice Alert or Tone Alert mode)
as you complete each step. The factory setting is Highway mode.
City Mode
X K Ka V S c
X K Ka V S h
To Change From Highway Mode to City Mode
Press and release
the City button.
Tone Voice Visual Display
One beep City
c appears
in the display
To Change From City Mode Back to Highway Mode
Press and release
the City button again.
Tone Voice Visual Display
Two beeps Highway happears
in the display
Settings •
When changing the Settings on your detector, please keep in mind:
JButtons can have multiple functions.
JDepending on your choice of Voice Alert or Tone Alert mode, you will
hear either voice messages or tones confirming changes in settings.
JAll settings will be stored in memory when the power is
turned Off and recalled when the power is turned back On.

Dim Button
Press and release
Settings
Your Detector
Nothing Comes Close to a Cobra®7
UltraBright Data Display Brightness
You can choose from three settings for Brightness of the display.
You can cycle through the settings by repeatedly pushing the Dim button.
The factory setting is Bright.
Press and
release Dim
button
To Change the Brightness to Dim
Press and release
the Dim button
once.
Tone Voice Visual Display
One beep Dim Display dims
To Change the Brightness to Dark
Press and release
the Dim button
again.
Tone Voice Visual Display
One beep Dark Display remains
dim (no visual
alerts will be seen)
To Change the Brightness to Bright
Press and release
the Dim button a
third time.
Tone Voice Visual Display
Two beeps Bright Display returns
to full brightness
Bright
Dark
Dim

Mute Button
Press and release
Settings
Your Detector
8English
Muting an Alert
Your detector allows you to quickly turn Off an audio Alert by momentarily
pressing the Mute button. If you press the Mute button a second time
during the Alert, the audio Alert will be turned back On.
Auto Mute Mode
Auto Mute will automatically reduce the audio volume of all alerts
after four seconds for as long as the signal is detected. The factory
setting for Auto Mute is On.
To Turn Auto Mute Off
Press and release
the Mute button
while no alert
is occurring.
Tone Voice Visual Display
One beep Auto Mute Off None
To Turn Auto Mute On
Press and release
the Mute button
again while no
alert is occurring.
Tone Voice Visual Display
Two beeps Auto Mute On None

IntelliMute Button
Press and release
Settings
Your Detector
Nothing Comes Close to a Cobra®9
IntelliMute
IntelliMute is a unique feature that allows you to avoid alerts you don’t need
to hear because you are stopped or moving slowly. By sensing the “revs”
(RPMs) of your engine, IntelliMute knows when you are at low speed and
automatically mutes audio radar alerts.
Before IntelliMute will work, you must set an activation point for your engine’s
revs (see page 10). Whenever the revs are below that point, IntelliMute will
begin muting. The activation point will be stored in memory and recalled
each time the power is turned On. The factory setting is IntelliMute Off.
NOTE
IntelliMute may not work with some vehicles because it cannot sense
the engine’s revs. In such cases, you can reduce unwanted audio alerts
by using Auto Mute and City mode when appropriate.
To Turn IntelliMute On
Press and release
the IntelliMute
button.
Tone Voice Visual Display
Two beeps IntelliMute On Dot appears next to
the large character
on the right
To Turn IntelliMute Off
Press and release
the IntelliMute
button again.
Tone Voice Visual Display
One beep IntelliMute Off Dot disappears

Settings
Your Detector
10 English
What to Remember While Using IntelliMute
IntelliMute works with both City and Auto Mute modes.
Whenever your engine revs are below the activation point, the dot next to
the large character on the right side of the display will remain lit. Above the
activation point, the dot will blink twice every two seconds.
If, for any reason, the unit stops sensing your engine’s revs, IntelliMute
will indicate an error and automatically turn Off.
The rev point you set will be stored in the unit’s memory when power is
turned Off and recalled each time the power is turned On.
NOTE
The rev point must be reset if you use your detector in a different vehicle.
NOTE
When initially choosing your IntelliMute activation point, a setting
of approximately 300 to 600 RPMs above idle is recommended.
You can reset the activation point at any time to fit your individual
preferences and driving style.
Setting the IntelliMute Activation Point
Your detector must be installed in your vehicle.
CAUTION
Do not attempt to set the rev point while driving.
Your vehicle should be parked and idling.
IntelliMute must be turned On before setting the activation point. Depending
on whether the unit is in Tone Alert or Voice Alert mode, you will hear a series
of beeps or voice messages as you follow the steps on the next page.
Below Activation Point
X K Ka V S c
Above Activation Point
X K Ka V S c

Your Detector
Nothing Comes Close to a Cobra®
IntelliMute Button
Press and release
To Set the IntelliMute Activation Point
Press and hold
the IntelliMute
button for two
seconds.
Tone Voice Visual Display
Two beeps Set Engine Revs None
Rev your engine to
the level you wish
to set (recommend
slightly above idle)
and hold revs steady
for two seconds.
None None Three bars will
flash in succession
At the desired
rev level, press
and release the
IntelliMute
button.
Three beeps IntelliMute Set All three bars flash
three times
Tone Voice Visual Display
Four beeps IntelliMute Error,
followed by
IntelliMute Off
Eappears
X K Ka V S E
NOTE
If the unit is unable to sense usable pulses within three
seconds or if you do not set a rev point within 20 seconds
of beginning these steps, IntelliMute will indicate an error
and automatically turn Off.
123
123
11
Settings

Settings
Your Detector
12 English
IntelliMute Pro
IntelliMute Pro prevents detection by radar detector detectors (RDDs) such as
VG-2, Spectre I and Spectre IV+ when traveling at slower speeds. It is intended
for use by experienced users only.
When IntelliMute Pro is turned On, and engine RPMs are below the IntelliMute
activation point, your detector’s radar detection circuits are turned Off to
prevent detection by RDDs.
Before IntelliMute Pro can be turned On, you must have turned On and Set the
IntelliMute activation point. (See pages 9 through 11.)
To Turn IntelliMute Pro On
While no signal
is being detected,
press and hold both
the IntelliMute
and City buttons
for four seconds.
Tone Voice Visual Display
Two beeps IntelliMute Pro On c or hwill blink
To Turn IntelliMute Pro Off
Press and hold both
the IntelliMute and
City buttons for
four seconds.
Tone Voice Visual Display
One beep IntelliMute Pro Off c or hwill show
steady
IntelliMute Pro On
X K Ka V S c
CAUTION
When IntelliMute Pro is On, NO radar signals will be detected and
NO alerts will be given at RPMs below the IntelliMute activation point.
IntelliMute Button
City Button
Press and hold both
buttons simultaneously

Voice/Tone Setting
You can set your detector to sound alerts with either a Voice or a Tone. You
can change settings by using the Mute button. In Voice Alert mode, you will
first hear several tones, then a voice message announcing the type of signal
detected, followed by more tones. In Tone Alert mode, you will hear the tones
only. The factory setting
To Turn VG-2 and Spectre I & IV+ Alerts On and Off
While no signal
is being detected,
press and hold the
Dim button for
four seconds.
Tone Voice Visual Display
On = Two Beeps Spectre VG-2 On Vwill blink twice
in the display
Your Detector
Nothing Comes Close to a Cobra®13
To Change From Voice Alert to Tone Alert
While no signal
is being detected,
press and hold
the Mute button
for two seconds.
Tone Voice Visual Display
One beep Tone Alert None
To Change From Tone Alert Back to Voice Alert
While no signal
is being detected,
press and hold the
Mute button for
two seconds again.
Tone Voice Visual Display
None Voice Alert None
Spectre VG-2 Off Vwill blink once
in the display
Off = One Beep
VG-2 and Spectre I & IV+ Alert Settings
Police use radar detector detectors (RDDs) to spot users of radar detectors.
Your detector is able to identify signals from VG-2, Spectre I and Spectre IV+
RDDs and can provide alerts when any of these or similar devices are in use
near your vehicle.
Your detector can be spotted by Spectre IV+ RDDs, but is invisible to VG-2
and Spectre I RDDs. You can choose whether you want to be alerted to VG-2
and Spectre I & IV+ RDD signals. The factory setting for VG-2 and Spectre I &
IV+ alerts is Off.
Settings

Settings
Your Detector
14 English
Radar Alert Settings
The detector allows you to choose whether it will show alerts on the X, K
and Ku bands. The factory settings are: X Band and K Band On; Ku Band Off.
To Turn K Band On and Off
While no signal is
being detected,
press and hold both
the Mute and City
buttons for four
seconds.
Tone Voice Visual Display
K On = Two beeps
K On Kwill blink twice
in the display
To Turn Ku Band* On and Off
While no signal is
being detected,
press and hold the
City button for four
seconds.
Tone Voice Visual Display
Ku On = Two beeps Ku On X and K will blink
twice in the display
Kwill blink once
in the display
K Off = One beep K Off
Ku Off X and K will blink
once in the display
Ku Off = One beep
To Turn X Band On and Off
While no signal
is being detected,
press and hold both
the Dim and Mute
buttons for four
seconds.
Tone Voice Visual Display
X On = Two beeps X On Xwill blink twice
in the display
X Off Xwill blink once
in the display
X Off = One beep
Pop Alert
The Pop Mode Radar Gun is a single-pulse Doppler radar that is a feature
of a K and Ka (Bee III Ka radar gun) band Instant-On radar gun. It uses
a single, short-time pulse to measure the target vehicle’s speed.
The Pop mode receiver senses Pop singles beyond the effective range of
Pop radar guns. As the Pop mode receiver is so sensitive, you should limit
the use of Pop Detect mode to highway and rural driving.
Pop Alert will alert you to Pop radar signals. During the alert, the unit
continues to detect other signals. The factory setting is Pop Detect Off.

Settings and Detection
Your Detector
Nothing Comes Close to a Cobra®15
Detection
The tables on the following pages show you the types of Signals your detector
will detect, as well as the voice and visual alerts it provides for each of them.
In Voice Alert mode you will first hear several tones, then a voice message
announcing the type of signal detected, followed by more tones. In Tone Alert
mode, you will hear the tones only.
In both Voice Alert and Tone Alert modes, a distinctly different alert tone is
used for each type of signal detected (including separate tones for each laser
signal). For X, K, Ka and Ku band radar signals, the tones will repeat faster as
you approach the signal source. The repeat rate of the tones gives you useful
information about the signal detected. (See responding to alerts on page 18.)
An indication of the type of signal detected will appear in the UltraBright
data Display. During X, K, Ka and Ku alerts, a number will also appear,
indicating the strength of the signal detected. (1 = weakest, 5 = strongest)
X Signal Detected
XK Ka V S 2X KKa V S 3X K Ka V S 5X K Ka V S 4
K Signal Detected Ka Signal Detected Ku Signal Detected
To Turn Pop Alert On and Off
While no signal is
being detected,
press and hold both
the Dim and City
buttons for four
seconds.
Tone Voice Visual Display
Pop On = Two beeps Pop On Pwill blink twice
in the display
Pop Off Pwill blink once
in the display
Pop Off = One beep
Pop Alert (continued)

Detection
Radar Signals, Voice and Visual Displays
Type of Signal Voice Visual Display
X Band Radar X Alert Xand Signal Strength
K Band Radar K Alert Kand Signal Strength
Ka Band Radar Ka Alert Ka and Signal Strength
Ku Band Radar Ku Alert XKand Signal Strength
Pop Radar Mode Pop Alert Pis Steady
During pop alerts, the letter Pwill
appear; and during laser alerts,
the letter Lwill appear, instead of
the signal strength indication.
During VG-2 or Spectre I or IV+
alerts, the letter Vwill appear.
It will be steady during VG-2
and blink during Spectre I or IV+.
During Safety Alert, the letter
Swill appear.
Safety Alert Signal Detected
X K Ka V S c
X Signal Detected
XK Ka V S 2X KKa V S 3X K Ka V S 5XKKa V S 4
K Signal Detected Ka Signal Detected Ku Signal Detected
16 English
POP Alert Signal Detected
X K Ka V S P
Laser Signal Detected
X K Ka V S L
VG-2 Alert Signal
Detected
X K Ka VS c
Spectre I or IV+ Alert
Signal Detected
X K Ka VS c
POP Signal Detected
X K Ka V S P
Your Detector