Codem Music Xpower 4000 User manual

N ext
BBLLKKMMOODDEEDDOOWWNN
▼
UUPP
▲
PPSSYY//DDIIMM GGAAMMEE//AAUUTTOO
R.C.S. manual
control
R.C.S. foot switches
control
Fig. 1 Xpower rear view
OUT 1
SOCKET
OUT 2
SOCKET
OUT 3
SOCKET
OUT 4
SOCKET
R.C.S.
IN
R.C.S.
OUT
POWER SUPPLY
220 VAC - 50 Hz
4000
USER’S MANUAL
GB

OUTPUT CONNECTOR WIRING
NOTE: BE SURE TO DISCONNECT POWER SUPPLY BEFORE ANY OPERATION !
Unscrew the central screw and remove connector’s top cover (fig. 2), take the
3 wires of projector’cable, screw the blu wire (neutral) to side terminal N,
screw the brown wire (live) to side terminal L, screw the yellow/green wire
(ground) to central terminal.
At the end screw down the two screws on the right to fix the cable (fig.2), close
the connector with top cover and screw down the central screw.
Once wired the connector, simply insert it in one of the 4 outputs (OUT 1/4)
in the rear of
Xpower (fig. 1).
Is preferred to connect the 4 outputs like fig. 3
INSTALLING INSTRUCTIONS
* WITH 4x1000 W LAMPS IS NOT POSSIBLE TO USE FILL FUNCTION BECAUSE TOTAL
LOAD EXCEED 16 A.
POWER SUPPLY CONNECTION
Connect the power plug in a 220V 50/60 Hz current socket.
Be sure that current socket is able to delivery required current.
NOTE: Total current load can not exceed 5 A per channel and 16 A for the 4 outputs
together.
LAMP POWER VS TOTAL CURRENT LOAD (when FILL function is active)
4 x 300 W lamps = 1,2 KW 5,5 A
4 x 500 W lamps = 2 KW 9 A
4 x 650 W lamps = 2,6 KW 12 A
4 x 1000 W lamps = 4 KW 18 A *
4
3
1
2
Front view
Fig. 3
Fig. 2

OPERATING INSTRUCTIONS
PSY BUTTON
•Push this button to activate PSY function.
The lamps are on for only 0,5 second.
• Push it again to return to normal mode.
• Push this button for over two seconds to
activate ZERO-CROSSING DIMMER.
The lamps light intensity is reduced to 50%.
• To return to 100% light intensity push it
again for over two seconds.
This light dimmer offer the advantage to
exclude noise in audio systems.
UP BUTTON
• Push this button to increase the game speed.
DW BUTTON
• Push this button to decrease the game speed
until stop.
N.B. There are two separated speed adjustments
for Sequential and Music mode.
BLK BUTTON
• After the ‘power on’ or after a RESET, push this
button to perform BLACKOUT (all lamps off).
• In blackout mode by
UP - DOWN - PSY -
MODE buttons you can switch on or off
manually each lamp.
• Push BLK button again to return in normal mode.
• Now each time you press BLK button, Xpower
show the last combination of lamps you made
manually.
• To have again the BLACKOUT FUNCTION
when pressing BLK button, you must turn off
manually all the lamps.
MODE BUTTON
Push this button to select sequentially these
functions:
• SEQUENTIAL FUNCTION
Xpower is in sequential mode.
• MUS FUNCTION (music)
By this function the game runs with music
signal.
N.B. By this function, game runs only if a signal
is picked up by internal microphone.
• FILL FUNCTION
By this function the lamps are always on.
GAME BUTTON
• Push this button to activate the MANUAL
GAME SELECTION.
• Push it again to select one game (1÷16).
• Push this button for over two seconds to
activate the AUTOMATIC GAMES SELECTION.
All games will be repeated 4 times each one.
▲
▲
Push this button for over two seconds to
activate a GENERAL RESET.
This function is useful if you must sincronize
more Xpowers connected togheter.

TECHNICAL SPECIFICATIONS:
• 220/240 Vac - 50 Hz single-phase supply.
• 4 channels x 1000 W MAX / internal fuse for each channel.
• 16 programmed games with automatic or manual selection.
• Microprocessor controlled.
• Music / Sequential / Psycosequential functions.
• Fill and Blackout functions.
• Zero-crossing Dimmer (50%/100%).
• Separated electronic speed adjustment for music or sequential mode.
• Internal microphone with automatic level control.
• R.C.S. input for external remote control of all functions or foot switches.
•R.C.S. output for other Xpower control.
• Zero-crossing system: no audio noise and longer lamps life.
• Optocoupled power stage with 16 A / 600 V triacs.
• Net weight: 4,6 Kg.
PACKING CONTENTS:
1 Xpower 4000, 1 Manual remote control R.C.S., 4 VDE male connectors.
N.B. We reserve the right to apport modify without notice.
R.C.S. REMOTE CONTROL CONNECTION
R.C.S. IN rear input (JACK MONO) allows to control all Xpower’s function by an external control
(Manual or foot switches) (see fig.1).
If you do not connect this input Xpower starts automatic games selection.
Connect in R.C.S. input only external control made by Next !
MULTIPLE Xpower CONNECTIONS
You can control several Xpower by only one Remote Control.
Insert R.C.S. control plug in R.C.S. IN of the first Xpower. Connect a JACK MONO cable between
R.C.S. OUT of the first and R.C.S. IN of the second one.
The operation is the same even if you use more than two Xpower.
NOTE: Disconnect power supply before any connection. Sincronize all Xpower pressing BLK button for
over two seconds.
R.C.S.
IN OUT
Xpower N°1 Xpower N°2 Xpower N°..
R.C.S.
IN OUT R.C.S. IN OUT
CODEM MUSIC S.r.l. -Via Del Vallo, 110 - 61100 PESARO - ITALY
Tel. [phone]- Fax [phone]
hhttttpp::////wwwwww..ccooddeemmmmuussiicc..ccoomm--EE--mmaaiill::iinnffoo@@ccooddeemmmmuussiicc..ccoomm