Coinco Money Controls MC Series User manual

MC Series Bill Acceptors
Installation Guide/Application Data
Operational Specifications
Product Features
• Bill widths accepted: MC2600 (66mm), MC7200 (72mm)
• Operating Voltages: 110VAC, 24VAC, 24VDC, 12 VDC
• Communication Interface: MDB, Pulse, Vend Serial, ccTalk,
ICT serial over RS232.
•Four-Way Acceptance
• Mounting: Upstack or Downstack
• Lighted Bezel (on standard mask only)
• Coupon capable
• Superior Stringing Protection
Operating Temperature Range: 0oF - 150oF
Storage Temperature Range: -22oF - 160oF
Input Power Requirements:
Bill Acceptance:
120 VAC 90-135VAC @1.0A
24VAC 20-32VAC @1.5A
24VDC 20-45VDC @1.5A
12VDC 10-14VDC @4A
Page 1
US $1 $5 $10 $20
CAD $5 $10 $20 $50 $100
EURO €5 €10 €20
RUR 5 10 50 100 500 1000

Bill Inlet Width
26 = 66mm
72 = 72mm
Bezel
0= See “Build”
1= Standard
2 = Slimline
Input Voltage/Protocol
1= 110VAC- Pulse, Vend Serial
2 = 24 VDC/AC MDBPulse
3= 12 VDC - Multi-Interface
4= 12 VDC - MDBWake/Sleep
MountingConfiguration
U= Up
D= Down
Cashbox Size
0= See “Build”
3= 300 Bills
5= 500 Bills
7 = 700 Bills
9= 900 Bills
B= 1100 Bills
N= None
I/O Harness
A= 110 VAC Power
C= 24VAC Power
M= MDB
I= Multi-Interface
W= Wake/Sleep
Build
00 = Standard
CountryCode
001 = Argentina
002 = Australia
005= Brazil
006 = Canada
014= Germany
041= United States
050= China
070= Euro
030= Russia
MC Series Model Naming Convention
MC x x x x x x x x x x x x
Page 2
Figure 1

Unpacking:
After unpacking the unit, inspect for any possible shipping damage. If
damaged, notify the shipping company immediately. Keep the carton
and packing material to reuse if you need to transport or ship the
changer in the future. Labels indicating the model and serial number
are on the side of the bill acceptor. Refer to these numbers when call-
ing upon your Coinco Service Center representative for information or
service.
Bezel Types
Page 3
Figure 2: Slimline Bezel Figure 3:Standard Bezel

Installation
NOTE: The Metal mounting plate must be connected to earth
ground.
1. Remove power from host machine.
2. Set bill acceptor dip switches, if required. (see Page 5).
3. Install the bill acceptor into the host machine using the mounting
studs and hardware in the machine.
4. Install / Connect the proper interface harness to the host machine.
5. Apply power to the machine, verify that the Green Flashing Arrows on
the front of the bill acceptor (with standard mask) are ON and blink-
ing. This condition indicates that the bill acceptor is ready to accept
bills.
• If the Lights are off, check connections and make sure power is
applied.
• Also check the rear diagnostic LED, the status codes are listed on
the cashbox and in the figure below.
6. Check Operation, once the Green Arrows are flashing, insert bills to
verify proper acceptance and credit.
Diagnostic LED
# of LED Flashes LED Status
Normal Pulse Rate
1 pulse per second
Ready
Fast Pulse Rate
3 pulses per second
Check Stacker/Cashbox
Not Lit Check Power
Steady ON Replace Acceptor
2 Flashes Bill Inhibited
3 Flashes Disabled by Host
4 Flashes Clear Bill Path
5 Flashes Clean Bill path
Page 4

Page 5
Dip Switch Configuration
OFF
ON
ON
OFF
1234 567 8
Front of MC Series Acceptor
PC Board
Figure 4
Dip Switch Locations
and Position
US Dip Switch ON/OFF Canadan Dip Switch ON/OFF Euro Dip Switch ON/OFF Russian Dip Switch ON/OFF
Switch 1 $1 enable/disable $10 enable/disable €5 enable/disable RUR 50 enable/disable
Switch 2 $5 enable/disable $20 enable/disable €10 enable/disable RUR 100 enable/disable
Switch 3 $10 enable/disable $50 enable/disable €20 enable/disable RUR 500 enable/disable
Switch 4 $20 enable/disable $100 enable/disable RESERVED RUR 1000 enable/disable
Switch 5 4Pulse / 1 Pulse per $1 RESERVED RESERVED Pulse / ICT Serial
Switch 6 Always / Harness enabled RESERVED RESERVED Short Pulse / Long Pulse
Switch 7 Short Pulse / Long Pulse RESERVED RESERVED 2 Pulse / 1 Pulse per RUR 10
Switch 8 Coupon enable/disable Coupon enable/disable RESERVED Always/Harness enabled

Cash Assess Door
Lift door to remove
cash
Cash Box
To Remove Bottom
Sensor Housing
(Access Bill Path)
Upstacking--
Push red latch down and
pull straight back
To Remove Cash Box
Upstacking--
Push red latch on top
forward. Lift up and back.
Interface
Connector
Standard
Bezel
Bill Entrance
Metal Mounting Plate
must be connected to
earth ground.
Diagnostic LED
Bottom Sensor Housing
MC2600/7200 Description
NOTE: The metal mountaing plate must be connected to earth
ground.
Page 6
Figure 5

Maintenance
Recommended Cleaning Material:
A mild solution of detergent can be used for cleaning the belts, bill path
and sensor lenses, as well as for general cleaning of the acceptor.
Beverages or other water-soluble liquids which have been spilled on or
into the acceptor can usually be removed with warm soapy water.
External surfaces can be cleaned with a damp cloth.
Note: Petroleum-based cleaners and freon-based propellants can dam-
age plastic and some electronic componenets. Scouring pads and stiff
brushes may harm the circuit boards and can mar the plastic. These
items should never be used when cleaning the bill acceptor.
Cleaning the Optical Sensor Lenses and Gray Scales
Warning: Remove power from the bill acceptor before opening the
bill path.
Remove the cash box and bottom sensor housing from the acceptor. To
clean the optical sensor lenses and gray scales use a "Lint Free" cloth
with a mild detergent. Repeat the cleaning process as needed until all
the sensor surfaces are free of contaminants. Remember to clean both
sensor lenses.
Page 7
Gray Scales
Bottom Sensor
Housing
Acceptor
(Cashbox removed)
Optical Sensor
Lens
Figure 6

Page 8
Figure 7: MC2600 Dimensional Drawing
(Up Stacking Position)

Page 9
Figure 8: MC7200 Dimensional Drawing
(Up Stacking Position)

Page 10
Figure 9: MC7200 Dimensional Drawing
(Up Stacking Position)