Bolts M8*35mm *4
Gas Piston *1
Back Cushion *1
Bolts M8X50mm *4
Gas Piston Cover *1
Seat Cushion *1
Bolts M8*50mm *4
Bolts M8*35mm *4
Bolts M8*45mm *2
Bolts M6*25mm *4
Bolts M8*25mm *2
Bolts M6*25mm *4
Star Base *1
Seat Plate *1
Plastic Caps *4
Bolts M8X25mm *2
Arms *2
Wrench *1
Bolts M8X45mm *2
Casters *5
Wrench *1
Plastic Caps *4
Wrench *1
Wrench *1
11
6
1
12
7
2
12
11
14
10
13
9
13
8
3
14
9
4
15
10
515
15
15
PRODUCT FEATURES
ASSEMBLY PARTS AND TOOL
ASSEMBLY INSTRUCTIONS
WARNING SAFETY INFORMATION
WEIGHT CAPACITY FOR SEATING: 500LBS
Sit in the center of the
chair with your back
against the backrest
Do not push the chair around
when a person is sitting in it
Do not sit at the front edge
of the chair
Do not push down on the
backrest when a person is
reclined
Do not stand on the chair
Do not place all your weight
on the backrest only
Do not use the chair with more
than one person
BEFORE YOU GET STARTED, A FEW POINTERS:
Mind the important safety
information
Having a friend to help makes
assembly extra-easy
Turn the Star Base(8) upside down, then press the Casters(5) into the holes at the end of
each base leg. Connect the Seat Cushion and Back Cushion together. Align the steel plate of Back
cushion over the pre-drilled holes underneath Seat cushion, and tighten the FOUR bolts
M8X35mm(11) by using the Wrench(15).
Turn the Seat-Back upright and align the center hole of the Seat Plate over the Gas
3LVWRQWKHQSXVKWKH6HDW&XVKLRQGRZQRQWRWKH*DV3LVWRQUPO\XQWLOWKHFRQQHFWLRQ
is secure. Attach the TWO Arms(4) to the Seat Cushion(2) with FOUR Bolts M8*50mm(12),
using the Wrench(15).
Adjust the balance on each side of the chair, and fully tighten all the bolts at this step.
Press the Plastic Caps(14) into the Arms holes to cover the bolts. Now, your chair is
successfully installed.
Insert the Gas Piston(6) into the center hole of the Star Base, the Gas Piston Cover(7)
should be placed over the Gas Piston.
Align the Seat Plate(3) over the pre-drilled holes underneath the Seat Cushion(2), make
sure that the front of the Seat Plate is facing the front of the Seat Cushion. Attach the Seat
Plate to the Seat Cushion using TWO Bolts M8*45mm(10) at the front and TWO Bolts
M8*25mm(9) at the back, tighten all the bolts with the Wrench(15), being careful not to
miss-thread the bolts or damaged the Seat.
Align two control handles of the Seat Plate(3) over the pre-drilled holes underneath the
Seat Cushion(2), attach two handles to the Seat Cushion using FOUR bolts M6X25mm(13),
tighten all the bolts with the wrench.
Step 1 Step 4
Step 5
Step 6
Step 2
Step 3
Note 1: Arm rests are labeled with an "L" (left) or "R" (right) to show which sides they should be
placed on.
1RWH’RQRWWLJKWHQDOOWKHEROWVWRDWUVWLVHQRXJKPDNHVXUHLWKDYHVSDFHWRDGMXVW
LQWKHQH[WVWHSV
Please read the instructions carefully and follow the assembly steps.
To ensure proper assembly, please follow all steps and use all parts provided. Not following
this warning may result in serious injury to you or others.
To prevent misalignments, keep the screws loose and do not tighten them until they are all
in their correct positions.
Avoid overtightening or forcing the screws, as this could cause them to break, strip, or
damage the threads of the holes.
Using the wrong size of screws for a particular part could cause damage to the screw or the
part.
Please lubricate all moving parts regularly and tighten all bolts and screws every 6 months,
or as needed.
Tight
Loose
1. Seat Height:Paddle-shaped lever on the right side
3. Rocking Tension: Long stem under the seat cushion with knob
2. Inatable Back Cushion: Inatable handle on right side
To inate the back cushion:
3UHVVLWFRQVWDQWO\WRLQ`DWHWKHEDFNFXVKLRQXQWLO\RXDUHVDWLVHG
with the fullness and comfort of your back.
+ROG\RXUEDFNDJDLQVWWKHEDFNFXVKLRQDQGXVH\RXUQJHUVWRSUHVV
WKHSOXJRQWKHLQ`DWHGKDQGOHWRGH`DWHWKHFXVKLRQ
To deate the back cushion:
While seated, turn knob forward
(toward + sign).
While seated, turn knob backward
(toward - sign).
To increase tension:
To decreas tension:
While taking your weight off chair, lift lever
up.
While taking your weight off chair, lift lever
up.
To raise:
To lower:
5
7
6
9
13
3
2
10
8
82
4
6
14
14
1
12
12
11
