COLAMY ZY-2199 User manual

Congratulations, you are now the owner of
a brand new STARSPACE chair!
Following this assembly guide and you will
find a quick start guide to assemble your
Starspace chair. We highly recommend
checking out our Assembly Videos as
well for even more detailed and visual
instructions.
If you run into any difficulty during the
assembly, remember to check out the
assembly Video to see if you've missed
anything. If you're unable to resolve your
problems, drop us an email as well and our
support team will assist you.
ASSEMBLY GUIDE
PACKAGE LIST
ASSEMBLY INSTRUCTION
STEP 1:
STEP 4:
STEP 5:
STEP 6:
STEP 7:
STEP 2:
STEP 3:
Step 1: Turn the Star Base(7) upside
down, then press the Casters(8) into the
holes at the end of each base leg, insert
the Lift(5) into the center hole of the Star
Base, the Lift Cover(6) should be placed
over the Lift.
Step 2: Align the Seat Plate(4) over the
pre-drilled holes underneath the Seat
Cushion(2), make sure that the front of the
seat plate is facing the front of the Seat
Cushion. Attach the Seat Plate to the Seat
Cushion using TWO Botls M6*25mm(10)
at the front and TWO Bolts M6*20mm(9)
at the back, tighten all the bolts with the
Wrench(13), being careful not to miss-
thread the bolts or damaged the seat.
Step 3: Turn the Seat Cushion(2) upright
and align the center hole of the seat
plate over the lift, then push the seat
cushion down onto the lift firmly until the
connection is secure.
Step 4: Attach the Arms(3) to the Seat
Cushion(2) with Four Bolts M8*25mm(11),
using the Wrench(13).
Step 5: Lay the Back Cushion on the
seat of the chair with the top of the
cushion toward the front. Attach the Back
Cushion(1) to the Arms by inserting Two
Bolts M8*25mm(11) in the TOP holes
with the Wrench(13).
Step 6: Rotate the back of the chair
up, then secure it with the LOWER Two
Bolts M8*25mm(11) with the Wrench(13).
Adjust the balance on each side of the
chair, and fully tighten all the bolts at this
step.
Step 7: Press the Plastic Caps(12) into
the Arms holes to cover the bolts.
Note 1: Arm rests are labeled with an "L"
(left) or "R" (right) to show which sides they
should be placed on.
Note 1: Arm rests are labeled with an "L"
(left) or "R" (right) to show which sides
they should be placed on.
Note 2: Do not tighten all the bolts to 100%,
make sure it have space to adjust in the
next steps.
65
7
11
11
8
10
11
11
2
9
4
11
12
12
CAUTION:
Make sure all bolts and screws are fully
tightened before using chair. Lubricate
all moving parts and tighten all bolts/
screws every 6 month or whenever
needed.
3
Contact us if you have
any issues
Mind the important
safety information
Having a friend to help
makes assembly
extra-easy
Scan this QR Code to watch our
assembly video for the chair.
Before you
get started,
a few
pointers:
o󰀩[e-mail]
[phone]
www.colamychair.com
SUBSCRIBE
Watch
video
Back Cushion *1 Lift *1 Bolts M6*20mm *2
Seat Cushion *1 Lift Cover *1
Bolts M6*25mm *2
Arms *2 Star Base *1
Bolts M8*25mm *8
Plastic Caps *8
Seat Plate *1 Casters *5 Wrench *1
1 5 9
2 6
10
3 7
11
12
4 8
13
MODEL:
ZY-2199
INSTRUCTION MANUAL
COLAMY CHAIR

INSTRUCTIONS FOR USE SAFETY AND MAINTENANCE
SAFETY INFORMATION
LIMITED WARRANTY
STARSPACE promises to repair or replace any STARSPACE chair that is found
to be defective in material or workmanship within one (1) year from the date of
original purchase so long as you, the original purchaser, still owns it. This is your
sole and exclusive remedy. This warranty is subject to the provisions below.
Seating Usage: Normal use for seating is identied as the equivalent of a single
shift, forty- (40) hour workweek. To the extent that a seating product is used in
a manner exceeding this, the applicable warranty period will be reduced in a
pro-rata manner.
Some retailers might have custom models imported direct from the factory and
therefore are not supported by our local service team because we don’t have
the correct parts, please contact your retailer directly for support. If you have
any questions about that we will be happy to assist and identify those items.
This warranty does not apply and no other warranty applies to:
EXCLUSIONS:
Normal wear and tear, which are to be expected over the course of ownership.
Misuse, abuse or excessive use of the product.
Modications or attachments to the product that are not approved by Starspace.
Products that were not installed, used, or maintained in accordance with product
instructions and warnings.
Products used for rental or commercial purposes.
Damage caused by the carrier in-transit is handled under separate terms.
We adopt a 30 days return policy which means that all products purchased on this
website may be returned to us within the timeframe. You need to contact us within
30 days after the product(s) came into your possession and the product(s) must be
returned to us without any undue delays.
RETURN POLICY：
Contact us through the contact form on our website and attach the invoice to the
message as a proof of purchase. And please also write the reason for return.
Returned products must be returned in the same condition as they were sent
and they must be sent in its original packaging.
We will then get back to you as soon as possible with information on where to
send the product(s).
If the product is not faulty, (i.e. if you changed your mind or if you are unhappy
with the product for some other reason), the cost of shipping will fall on
you. And it is your responsibility that the package arrives safely to us so we
recommend that you use a courier service where it is possible to track the
shipment.
As soon as we have received the product(s) and made an inspection we will
inform you of our decision.
If the product is faulty when you receive it please contact us and we will help
you out.
We reserve the right to give a partial refund in cases when the product(s) is not
in an unused condition, is damaged or have missing parts not due to our error.
HOW RETURNS WORK：
If a refund is approved we will automatically credit the purchase to your credit
card or original method of payment.
1.Seat Height:Paddle-shaped lever on the right side
2.Tilt Tension: Long stem under the seat cushion with knob
3.Operating the tilt lockout
To raise:
To increase tension:
To lower:
To decrease tension:
While seated, lift lever up.
While seated, turn knob
backward (toward - sign).
To stop your chair from tilting,sit
forward,then push the control
handle in.
While taking your weight off
chair, lift lever up.
While seated, turn knob
forward (toward + sign).
To let your chair tilt back,pull
the control handle out.
At the proper height, your feet should rest flat on the floor.
At the proper height, your feet should rest flat on the floor.
*
*
+
_
Do not stand on the chair, Do Not use the chair as stepladder.
Use this product for seating one person at a time.
Do not use the chair unless all bolts and screws are rmly secured.
Avoid contact with sharp objects to prevent puncturing the fabric.
Every 6 months, check all bolts and screws to ensure they are tight.
To clean, spot clean only using a damp towel and mild cleaner, rst
test on a small, obscure area of fabric.
Chair weight limit not to exceed 250 lbs.
Sit in the center of
the chair,with your
back to the backrest
Do not push the
chair around when a
person is sitting in it
Do not sit at the
front edge of the
chair
Do not push down
on the backrest
when a person is
reclined
Do not stand on the
chair
Do not place all
your weight on the
backrest only
Do not use the chair
with more than one
person
Scan this QR Code to watch our
assembly video for the chair.
o󰀩[e-mail]󰀩[e-mail]
[phone]+1 628-222-2513
www.colamychair.comwww.colamychair.com
SUBSCRIBE
Watch
video
MODEL:
ZY-2199
INSTRUCTION MANUAL
COLAMY CHAIR