Coleman 2000002120 User manual

STITCH LINE
BEACH SHADE MODEL 2000002120
Fig. 1
Fig. 2
To Set Up Beach Shade
1. Unfold Beach Shade and spread out on a clean, level surface
with the door facing the desired direction. Unzip door.
(Fig. 1)
6. Insert one end of the grey Crossover Pole into the grommet
on the web strap on either side of front door. (Fig. 4)
Fig. 6
Fig. 4
8. Go to the back of the
Beach Shade and
insert black Main Pole
tip into the grommet
on the web strap.
(Fig. 6)
To Set Up Beach Shelter (continued)
Fig. 5
(continued on other side)
Main Poles (2)
Crossover Pole (1)
2. Stake down shade corners,
using the outside grommets on
the web straps. Keep the floor
taut. (Fig. 2)
Option: Use sand bags to weight
shelter down, see Fig. 14 & 15.
7. Go to opposite end of the grey pole and gradually apply
pressure to the pole, forming an arch, until you are able to
insert the pole tip into the grommet on the web strap. (Fig. 5)
9. From the front of the Beach Shade, gently pull the black Main
Pole down until you
can insert the end into
the grommet on
the web strap located
above the door open
ing. (Fig. 7)
10. Repeat for the
second black
Main Pole.
(Fig. 8)
Fig. 7
Fig. 8
Before you begin
Read all instructions before set up.
• Select a level site clear of rocks, branches, and other hard or
sharp objects, to install your Beach Shade.
WARNING: Keep clear of overhead power lines.
• Do not set up your Beach Shade under trees because of potential
lightning strikes or falling tree limbs in inclement weather.
• Secure with all stakes and guylines provided to prevent
property damage or personal injury.
• For best results in windy conditions, position narrow end of
Beach Shade into the wind.
• Enlist the help of at least one other person to assist you when
it is time to assemble the Beach Shade.
Pole Descriptions
Pole Pole Pole
Description Qty. Dia. Repair Kit Replacement Kit
Main Poles, black 2 8.5mm 5010000541 5010000547
Crossover Pole, grey 1 9.5mm 5010000540 5010000548
3. Assemble both Main (black) Poles and the Crossover (grey)
Pole by interlocking shock-corded sections.
4. Insert the black Main Poles through the pole sleeve running
from the front to the back. (Fig. 3)
5. Insert the grey Crossover Pole through the pole sleeve
running side to side. (Fig. 3)
Fig. 3
Black Poles
Grey Pole
Front of the Beach Shade

STITCH LINE
To Set Up Beach Shelter (continued)
To Store
1. All poles and metal stakes must to be placed in the storage
bag to prevent damage to the fabric items placed in the
carry case.
2. Make sure Beach Shade is clean and dry before placing in
carry case.
3. Neatly fold Beach Shade to width of pole storage bag. Place
storage bag on folded Beach Shade, roll tightly, and place in
carry case.
4. Store in a clean, dry area.
To Secure Beach Shade in Sandy Terrain
1. Fill the (6) sand bags with sand or small rocks. (Fig. 14)
2. Insert the toggle of the filled sandbag through the grommet
on the stake loop where the stake would have been. (Fig. 15)
3. Bury the sand bag to secure the Beach Shade.
4. Tie the end of the guy line to the sand bag, extend and bury.
Repeat for second guy line.
12. Extend guy lines out until
taut then secure with stakes.
(Fig. 10 & 11)
Fig. 10
Fig. 11
Fig. 14
11. Attach guy lines to the front of the Beach Shade, above the
large door, by
inserting the guy
line through the
webbing between
the grommet and
the shade material.
(Fig. 9)
NOTE: Use cord located above front door of the Beach Shade
as a dry line.
Rear Vent Flap
The rear flap of the Beach Shade may be raised and lowered to
allow for better ventilation, improve lighting, or privacy.
1. Unzip inside flap to expose mess screen for ventilation.
2. Roll flap up and secure by inserting both dowels through
loops. (Fig. 12)
Fig. 12
Loops &
Dowels
3. Undo outer zipper on rear vent flap and roll up for ventilation
or additional access to Beach Shade.
4. Roll flap up and secure by inserting both dowels through
loops. (Fig. 13)
Fig. 13
Loops &
Dowels
Fig. 9
Fig. 15
The Coleman Company, Inc. • 3600 N. Hydraulic • Wichita, Kansas 67219
1-800-835-3278 • www.coleman.com
MADE IN BANGLADESH • PRINTED IN BANGLADESH
© 2008 The Coleman Company, Inc.
Coleman®, , and are registered trademarks of The Coleman Company, Inc.
4010004156 (20081104)
Things You Should Know:
• Under certain conditions (cold weather, high humidity, etc.) condensa-
tion will form on the inside of your shelter. Condensation is caused
by water vapor from your breath, perspiration, or any wet clothing inside
the shelter. It is NOT LEAKAGE through the shelter fabric. It can be
minimized by removing wet clothing from your shelter and by providing
good ventilation through the shelter.
• Tree limbs, tree sap, bird droppings, or moisture steadily dripping off
tree limbs can cause damage to the shelter fabric and its coating
resulting in leaks or loss of flame-resistant properties.
• Never store shelter even for a short period of time, without drying
it thoroughly and brushing off caked dirt. Do not pack stakes or poles
inside your shelter. Use a separate storage bag.
• Stakes should be removed by pulling on the stake itself. NEVER PULL ON
THE SHELTER TO REMOVE STAKES AS THIS COULD RESULT IN
PROPERTY DAMAGE OR PERSONAL INJURY.
• Shelter poles should not be left telescoped together during storage.
• Do not leave your shelter set-up for weeks at a time. Be aware that
exposure to ultraviolet rays from the sun can seriously damage material
and/or cause it to become discolored.
WARNING: Keep all flame and heat sources away
from this tent fabric.
This tent meets the flammability requirements of CPAI-84. The
fabric may burn if left in continuous contact with any flame source.
The application of any foreign substance to the tent fabric may
render the flame-resistant properties ineffective.
Front Door Flap
For additional privacy, the front panel (door) of the Beach Shade
is equipped with a zippered closure.