Combi Smart Hold OKF11 Installation instructions

Combi Vertical Diaper Changing Station “Smart Hold OKF11”
[To the person in charge of installation]
The inspection after the installation is the same as the daily
inspection. After installation is complete, inspect the product by
referring to 2 Daily Inspection on pages 3 to 4.
Save This Manual for Future Reference
Combi Vertical Diaper Changing Station
“Smart Hold OKF11”
Daily Inspection and
Periodical Inspection Manual

Combi Vertical Diaper Changing Station "Smart Hold OKF11" Daily Inspection and Periodical Inspection Manual
1Part Name
Introduction
Table of Contents
1 Part Name ....................................... page 2
2 Daily Inspection ............................... page 3
3 Periodic Inspection .......................... page 5
4 Part Replacement ............................ page 8
5 Others ........................................... page 10
This manual describes the details of "Daily Inspections" and "Periodic Inspections" required for the
comfortable and safe use of Combi Vertical Diaper Changing Station " Smart Hold OKF11". Be sure to perform
daily or weekly inspection and annual periodic inspections in accordance with the contents of this manual.
Main Body Sticker
Bottom Cover
(Panel Base)
Hinge Cover
(Right)
Hinge Cover (Left)
Top Cover (Panel Top)
Instruction Sticker
Belt
Buckle
Baggage Hook Sticker
Head Cushion Seat Cushion
Table Panel (Head Lower)
Serial Sticker
(Sticker at far right)
Inspection Sticker
Baggage Mark Sticker
Side Guard
Table Panel
(Head Upper)
Baggage Hook
(left and right)
Product Life
The product life is 7 years in normal use. The product must be replaced at the end of the product life.
The storage period for repair parts is 5 years after the nal production.
2

①
No scratches, cracks or rattling on the buckle.
②
No fray or damage on the belt.
③Insert the buckle until it clicks, and pull the
belt to make sure the bukkle is not relrased.
Daily inspections are carried out daily or weekly basis by visual and touch. No tools are used.
①The parts should not be missing or the
seat cushion or head cushion are not
loose.
② Close the main body and conrm that the
table panel does not rattle by shaking.
①
Open the main body and conrm that the
table panel does not rattle by swinging it
from side to side.
②Opening and closing of the table panel
should be smooth.
③No scratches or cracks.
Checking
Buckle
Confirmation
of releasing
the buckle
⑤The belt shall be free from twisting and it
can be stored smoothly.
If any malfunctions are found during the inspection, immediately discontinue the usage and contact
sales agent to request service.
❷Released
❶Press
❶Press
Buckle Holder
* Replace the belt (with retractor) if the belt is
broken, frayed, or severely soiled. Refer to 4 Parts
Replacement, "Belt Replacement Procedure" on
page 8.
Buckle
Buckle
2Daily Inspection
Checking belts and buckles
Checking external appearance
Checking the open/close operation of the table panel
④The buckle can be fastened an released
reliably.
3

Combi Vertical Diaper Changing Station "Smart Hold OKF11" Daily Inspection and Periodical Inspection Manual
The sticker should be properly affixed and contents are readable. (No scratches, tears, missing,
or discoloration)
The contents should be readable. (dirt mark, graffiti, etc.)
* The sticker contains warnings and cautions for safety use.
Guide Sticker
Attached to the entrance of the toilet,
or to the door of the toilet booth, etc.
Warning Sticker
Attach to a position near the
product and easy to see
Main Body Sticker
Front of the table panel
Instruction Sticker
Front of the top cover
when the table is open.
Baggage Mark Sticker
(2 pcs)
Both sides of the table panel
Warning Sticker
Main Body Sticker
Instruction Sticker
Baggage Hook Stickers (2 pcs)
Serial Sticker
Upper right of the upper cover
(Lot No in lower column)
Baggage Hook Stickers
(2 pcs)
Both sides of the side guard
Inspection Sticker
Upper cover, lower right
Baggage Mark Sticker (2 pcs)
Serial Sticker
Inspection Sticker
Toilet Entrance Toilet Booth
Place of Application
Checking stickers
4

● Periodic inspections are conducted periodically about
once a year.
● In the periodic inspection, check the daily inspection
points and remove each part according to the following
and check the condition of each part.
If any issues are found during inspection,
immediately discontinue the usage and contact
sales agent to request service.
The screws (3 locations) on the back of the
buckle should not be missing or loose.
Remove the head cushion and check the
upper cover xing screws and washers (2
locations) are not missing or loose, and
then remove the screws.
After checking the lower cover xing screws
[2 locations ] are not loose, and then
remove the screws.
Philips screwdriver, wrenches, etc. Caution
Be sure to tighten the screws by hand.
The plastic part may be damaged if power tools
are used.
Check the screws used for each part for damage of the
cross-recess, deformation of the screws, and rust. If any
abnormality is found, replace the screws with new ones.
Remove the top cover from the frame.
Buckle
Head Cushion
Top Cover
3Periodic Inspection
Required Tool
①Check the screws on the buckle ② Check the upper cover xing screws
③ Check the lower cover xing screws
5

Combi Vertical Diaper Changing Station "Smart Hold OKF11" Daily Inspection and Periodical Inspection Manual
Check the 3 anchor bolts for fixing the leg
frame are not missing or loose.
Leg Frame
Anchor Bolt
Remove ❶the bottom cover and ❷hinge
covers from the frame in this order.
❶
❷
Lower Cover
Hinge Cover
It is xed to the large hole.
❸
❶❷
❹
Check that the anchor bolts (6
locations) are not missing or
loose.
Check no rust on the main body
frame
When the table panel is closed the
tools can be used for the lower 2
holes, ❺and ❻from the front.
④ Checking the xing anchor bolts for the leg frame
⑤ Check the rust on screws to x to the wall and the main body frame
For concrete and ALC
❻➡
Right Side
❺➡
6

Secure the lower cover
with the screws.
When the table panel is closed the tools
can be used for the lower 2 holes, ❻and
❼from the front.
It is xed in the small holes.
❸
❶❷
❹
Check the screws (7 locations) are not
missing or loose.
Check the main frame for rust. ❺
Put
❶
hinge cover,
❷
lower
cover on the frame in this
order.
❶
❷
Secure the
top cover to
the frame with
screws and
install the head
cushion.
❶
❷
❸
Hinge Cover Top Cover
Head Cushion
①Retractor operates smoothly and it locks.
②The buckle clicks on the buckle receiver and locks.
⑦Check the operation of the retractor and buckle.
⑤ Check for rust on wall xing screws and main body frame
⑥Assembly
For partitions, gypsum boards
❼➡
Right Side
❻➡
Insert at back
side of upper
cover (left and
right)
Lower Cover
Insert into the holes of the
frame by pushing 2 locations. Insert at lower
side of upper
cover (left and
right)
7

Combi Vertical Diaper Changing Station "Smart Hold OKF11" Daily Inspection and Periodical Inspection Manual
Belt Replacement
If broken, frayed, or severely soiled belt is found during daily inspections. It is recommended to
purchase "Belt Retractor Replacement Set" and replace it in the following procedure.
Remove buckle
Remove the metal rod and drop the belt into the belt hole.
Remove the seat cushion and head cushion. Remove the xing screws and washers
(2 locations) and remove the top cover.
Remove the table panel (top).
Remove the table
panel xing screws
(13 locations).
Remove the baggage
mark stickers (2
locations).
Buckle Metal Rod
Top Cover
Caution
The sticker may damaged, use
enclosed new baggage mark
sticker (2 pcs).
* Included in replacement sets.
❶ ❷
❸ ❻
❼ ❽
󱢳󱢴󱢵
❹ ❺
❾ 󱢶
Table Panel
(Upper)
Belt
Seat Cushion
Head Cushion
* Replace the belt with a retractor.
* It can be removed without tools.
4Part Replacement
21
43
5
8

Remove the 4 fixing screws and replace the
belt including the retractor.
Extract the belt from the retractor and pass through
the belt hole in the table panel (upper side).
Secure the table panel (inside) with screws (13 locations).
Secure the buckles with the screws (2 locations).
Refer to 5for the position of the screw.
Affix new baggage
mark stickers (2
locations).
Belt
Table Panel
(Upper)
If a metal bar is
passed through the
belt, it will not fall
into the belt hole.
Metal Rod
Secure the top cover with the screws and washers (2 locations).
Attach the seat cushion and the head cushion. Check the belt and buckle.
Top Cover
①No scratches, cracks or rattling on the buckle.
②No fray or damage on the belt.
③Insert the buckle until it clicks, and make sure it is
fastened by pulling the belt.
④The buckle can be locked and unlocked reliably.
⑤The belt shall be free from twisting and shall be
stored smoothly.
(See page 3 for the inspection method.)
Seat Cushion
Head Cushion
76
9
8
11
10
12
Retractor
9
Press the two area of the connecting
tape by hand securely.

Combi Vertical Diaper Changing Station "Smart Hold OKF11" Daily Inspection and Periodical Inspection Manual
Refer to Belt Replacement 1to 5for the disassemble of the table panel.
Turn the table panel over and remove the screws. Replace the buckle holder and x it with screws.
For the assembly of the table panel, see "Belt Replacement" on 7to 󱫒on page 9.
(Be sure to inspect the belt and buckle after replacement.)
5Others
After periodic inspection, enter
the inspection date on the
<Inspection Sticker> attached to
the upper cover (lower right).
Inspection sticker are available
for purchase.
Inspection
Sticker
Inspection Sticker
Recording inspection dates
To ensure safety use of the product, the warning
stickers are enclosed as an accessory to the
product. Additional sticker are available for purchase. Warning
Sticker
Warning Sticker
Procedure of replacing buckle holder
● This product is a dedicated for changing diaper for
children. Clean regularly to keep immaculate after
installation.
● When cleaning, use diluted neutral detergent to
wipe, then wipe it with wet cloth, then wipe with
dry cloth to take off moisture.
Cleaning
Caution
Do not use detergents other than neutral
detergents. Deterioration, fade, or crack may
occur on plastic and they cause damage.
10