Comet BL1540 User manual

T
INSTRUCTION MANUAL
2 IN 1 BLENDER
Read this manual thoroughly before using and save it for future reference
Model:BL1540

1
IMPORTANT SAFEGUARDS
When using this electrical appliance, basic safety precautions should always be followed,
including the following:
1. Read all instructions.
2. Before using check that the voltage indicated on the product corresponds with the
voltage of your electrical outlet.
3. Do not let cord hang on hot surface or over edge of table or counter.
4. Do not operate any appliance with a damaged cord or plug or after the appliance
malfunction or has been damaged in any manner. Return the appliance to the nearest
authorized service facility for examination, repair or adjustment.
5. If the supply cord is damaged，it must be replaced by the manufacturer or its service
agent or a similarly qualified person in order to avoid a hazard.
6. Close supervision is necessary when any appliance is used by or near children.
7. Avoid contacting the moving parts.
8. Keep hands and utensils out of container while blending to reduce the risk of severe
injury to persons or damage to the blender. A scraper may be used but must be used only
when the blender is not running.
9. The use of attachments not recommended or sold by manufacturer may cause fire,
electric shock or injury.
10. Unplug from outlet when not in use, before putting on or taking off parts, and before
cleaning. To disconnect, turn any control to “0”, then remove plug from wall outlet by
grasping the plug, not the cord.
11. To reduce the risk of injury, never place blade assembly on motor unit without the jar
properly attached.
12. This appliance shall not be used by children. Keep the appliance and its cord out of
reach of children.
13. Appliances can be used by persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way and if they understand the
hazards involved.

2
Children shall not play with the appliance.
14. Do not leave the machine on unattended.
15. When removing the blender from the motor unit, wait until the blades have completely
stopped.
16. Always operate blender with cover in place.
17. Always use the appliance on a secure, dry level surface.
18. Never place this appliance on or near a hot gas or an electric burner or where it could
touch a heated appliance.
19. Do not use outdoors.
20. Do not use appliance for other than its intended use.
21. Do not operate without this cover in place;
22. Avoid any contact with blades or movable parts.
23. Switch off the appliance and disconnect from supply before changing accessories or
approaching parts that move in use.
24. Always disconnect the appliance from the supply if it is left unattended and before
assembling, disassembling or cleaning.
25. This appliance is intended to be used in household and similar applications such as:
– staff kitchen areas in shops, offices and other working environments;
– farm houses;
– by clients in hotels, motels and other residential type environments;
– bed and breakfast type environments.
26. Care shall be taken when handling the sharp cutting blades, emptying the bowl and
during cleaning.
27. Be careful if hot liquid is poured into the appliance as it can be ejected out of the
appliance due to a sudden steaming.
28.This appliance is not appropriate to have long contact with food.

3
HOUSEHOLD USE ONLY
KNOW YOUR BLENDER
BEFORE THE FIRST USE
Check that all parts are complete and not damaged. Choose the appropriate attachment to
perform your desired task. The blender attachment is suitable for blending fruits or
vegetables or crushing ice, while the grinder attachment for grinding coffee beans. Clean
the attachment according to the section “CLEANING AND MAINTENANCE”.
WARNING: The blade is sharp, handle with great care and ensure that unplug the
appliance from outlet before assembling and removing parts.

4
HOW TO USE
1. Peeled or cored the fruit or vegetables and then cut it into small dices.
2. Place the food to be blended into the jar. Usually, certain amount of purified water has to be
added to facilitate the smooth running of appliance. The proportion of the food and water is
2:3.The amount of mixture should not exceed the max level as indicated on the jar.
RECIPE
FOOD TYPE SPEC WEIGHT SPEED
Carrot Cut into 15mm*15mm*15mm Carrot: 600g
Water: 900g High speed
Note: never use boiling liquids or run the appliance empty.
3. Put the lid on the jar. Be sure the measuring cup is in place.
4. Plug the power cord into a standard wall outlet.
5. Choose to the appropriate speed setting for your task(Please stir food at the highest
speed,but not at low speed).
6. For quick or delicate blending tasks, press the key to “ P” position and hold for a few seconds
and then release, the key will reset to “O” position automatically. Operate several times until
the consistence you want is obtained
7. If you want to add ingredients while the blender is working, remove the measuring cup and
place through the lid opening.
8. When crushing ice or hard food, keep one hand firmly on the lid.
9. When the consistence you desire is obtained, press the key to “O” position.
Note: 1) For each use, the consecutive operation time should not exceed 2 minutes. at least 10
minutes rest time must be maintained between two continuous cycles, let the unit cool to room
temperature before performing next operation cycle.
2) If you want to stop the machine during operation, press the key to “O” position anytime.
10.The function of the “P” is to break ice and pulse,indicating P-file.
BLENDER OPERATION
1. Lay the motor unit on the flat horizontal surface and make sure it is unplugged.
NOTE: There is a safety interlock device at the bottom of jar, if the jar is not
assembled in place, the blender will not operate.
2. Open the jar cover by turning anticlockwise and place it on the surface. Peel or core the
fruits or vegetables and then cut it into small pieces, then put them into the jar. Usually

5
certain amount of purified water has to be added to facilitate the smooth running of
appliance. The amount of mixture should not exceed the max level as indicated on the
jar, nor sit lower the min level. The best proportion of the fruits or vegetables and water
is 2:3.
NOTE: The blender is not applicable for beating egg white, mashing potatoes, mixing
dough, extracting juice from fruit and vegetable.
3. Replace jar cover on the jar and turn it clockwise.
NOTE: There is a safety interlock device at the side of jar cover, if the jar cover is not
assembled in place, the blender will not operate.
4. You may add ingredients into the jar through the center opening of jar cover during
operation, then replace measuring cup if necessary. Let the tabs of measuring cup aligns
with the grooves of jar cover, put down and turn the measuring cup by clockwise until it
in place.
5. Ensure the Speed Selector to “ 0” Position,then plug into power outlet and set Speed
Selector to your desired setting. You can press down the Pulse button without releasing
it if want to accelerate the process of blending. The detailed information is shown in
below Fig. 1
NOTE: Make sure the jar cover is placed in position completely before operating, and
never open the jar cover during operation.
6. Do not run the appliance for more than 2 minutes per time, and only wait until the unit
is cooled to room temperature before performing next operation cycle.
7. Turn the Speed Selector to “ 0” position once the mixture has been blended to your
Fig. 1

6
desired consistency.
8. Turn the jar anti-clockwise and remove it from the motor unit, carefully take down the
jar cover, then pour and serve.
GRINDER OPERATION
1. Place the motor unit on the flat horizontal surface and make sure it is
unplugged.
2. Fill the grinding bowl with proper coffee bean, then assemble the
grinding blade assembly and grinding bowl together. Please see
Fig.3
NOTE: The quantity of coffee bean the grinding bowl allows to
grind is Max 50g.
3. Place the grinder attachment on the motor unit, Please see Fig. 4
NOTE: There is a safety interlock device at the bottom of grinder, if
the grinder is not assembled in place, the chopper will not operate.
4. Ensure the Speed Selector to “OFF” Position, then plug into power outlet.
5. Select the fastest speed setting, the appliance will start grinding. During grinding, you
can press down the Pulse without releasing it if want to accelerate the process of
grinding.
6. Turn the Speed Selector to “OFF” Position once the coffee has been ground to your
desired result.
7. Disconnect from power supply once finished. Disassemble the grinder attachment from
the unit, keep the grinding bowl downward and turn it anticlockwise (see fig.5), then
empty the bowl and serve.
8. Do not run the appliance for more than 30 second per time, and only
wait until the unit is cooled to room temperature before performing
next operation cycle.
WARNING:
1. Never operate the appliance continuously for more than 2 minutes per time.
Fig.3
Fig.4
Fig.5

7
2. Blades are very sharp. Handle with care.
3. Do not operate without the jar cover in place.
4. Do not disassemble the jar or bowl from the jar base or bowl base in general condition.
5. This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
6.Blending maximum level load or hard fruits and vegetables must be sure that the speed
selector is setting at highest speed (speed 2). If the speed is used too low, the motor will be
damaged due to insufficient torque. When the motor speed is found to be too slow, you
must immediately use a higher speed setting to blend or turn the speed selector to “0” to
stop blend!
CLEANING AND MAINTENANCE
Make sure to disconnect appliance from power supply before cleaning
For blender
The Auto Clean function can clean the blender easily and rapidly in complete safety.
1. Pour a little warm soapy water into the Jar and turn the Speed Selector to “1” position
and press down the Pulse button without releasing it for a few seconds.
2. Dismantle all detachable parts.Dissemble the Jar from the motor unit and rinse it under
running water, then detach the blade assembly from the jar assembly, take the blade
assembly out, finally remove the jar base seal ring . In addition, detach the measure cup
from the jar cover. Rinse the jar, blade, jar base, jar cover and measuring cup under
running water.

8
3. Wipe the outer surface of motor unit and with a damp cloth.
NOTE: Do not use abrasive cleanser and never immerse motor unit in water for
cleaning
4. Dry all parts and then assemble them. The method of assembling blender attachment
just is in opposite of its detaching sequence.
NOTE: If any problem has been encountered during using, never disassemble the
Motor Unit by yourself. There are no user serviceable parts inside. Only contact the
authorized service facility for examination and repair.