Romina 4501 User manual

4501 VENTIANNI
CONVERTIBLE CRIB
ASSEMBLY INSTRUCTIONS FOR THE
WARNING: THE PROPER USE OF THIS
CRIB IS IMPORTANT FOR YOUR BABY’S
SAFETY. IN ORDER TO KEEP YOU
BABY SAFE AND SECURE, AS WELL AS
AVOID POTENTIAL INJURY OR DEATH,
PLEASE READ AND BECOME FAMILIAR
WITH ALL THE WARNINGS, CAUTIONS
AND INSTRUCTIONS IN THIS BOOKLET.
KEEP THIS INSTRUCTION BOOKLET
FOR FURTHER USE.
DO NOT THROW THIS BOOKLET AWAY!
this picture shows what you crib should look like after completing the assembly process
READ ALL INSTRUCTIONS
BEFORE ASSEMBLING THE
CRIB. KEEP THE INSTRUCTION
BOOKLET FOR FURTHER USE.
NEVER USE THE PLASTIC
SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS
COVERS, AS THEY CAN CAUSE
SUFFOCATION.
MAKE SURE TO SELECT THE
CORRECT SIZE MATTRESS.
INFANTS CAN SUFFOCATE IN THE
GAPS BETWEEN THE CRIB SIDES
AND A MATTRESS THAT IS TOO
SMALL.
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY
THE CONSUMER PRODUCT SAFETY
COMMISION AND BY THE AMERICAN
SOCIETY FOR TESTING AND MATERIALS.
4300 Northlake Ct, Ste E, Charlotte,
NC 28216
Phone: [phone]
www.rominafurniture.com

INFANTS CAN SUFFOCATE ON SOFT BEDDING.
NEVER ADD A PILLOW OR COMFORTER. NEVER
PLACE ADDITIONAL PADDING UNDER AN INFANT. FAILURE TO FOLLLOW
THESE WARNINGS AND ASSEMBLY INSTRUCTIONS COULD RESULT IN
SERIOUS INJURIES OR DEATH.
- TO REDUCE THE RISK OF SIDS, PEDIATRICIANS RECOMMEND HEALTHY INFANTS BE PLACED ON
THEIR BACKS TO SLEEP, UNLESS OTHERWISE ADVISED BY YOUR PHYSICIAN.
STRANGULATION HAZARD:
- STRINGS CAN CAUSE STRANGULATION! DO NOT PLACE ITEMS WITH A STRING AROUND A
CHILD'S NECK, SUCH AS HOOD STRINGS OR PACIFIER CORDS. DO NOT SUSPEND STRINGS OVER
A CRIB OR ATTACH STRINGS TO TOYS.
- TO HELP PREVENT STRANGULATION, TIGHTEN ALL FASTENERS. A CHILD CAN TRAP PARTS OF
THE BODY OR CLOTHING ON LOOSE FASTENERS.
- DO NOT PLACE CRIB NEAR WINDOW WHERE CORDS FROM BLINDS OR DRAPES MAY STRANGLE
A CHILD.
FALL HAZARD:
- WHEN CHILD IS ABLE TO PULL TO A STANDING POSITION, SET MATTRESS TO LOWEST POSITION
AND REMOVE BUMPER PADS, LARGE TOYS AND OTHER OBJECTS THAT COULD SERVE AS STEPS
FOR CLIMBING OUT.
- STOP USING CRIB WHEN CHILD BEGINS TO CLIMB OUT OR REACHES THE HEIGHT OF 35 IN. (89
CM).
- CHECK THIS PRODUCT FOR DAMAGED HARDWARE, LOOSE JOINTS, LOOSE BOLTS OR OTHER
FASTENERS, MISSING PARTS, OR SHARP EDGES BEFORE AND AFTER ASSEMBLY AND
FREQUENTLY DURING USE. SECURELY TIGHTEN LOOSE BOLTS AND OTHER FASTENERS. DO NOT
USE CRIB IF ANY PARTS ARE MISSING, DAMAGED OR BROKEN. CONTACT ROMINA FURNITURE FOR
REPLACEMENT PARTS AND INSTRUCTIONAL LITERATURE IF NEEDED. DO NOT SUBSTITUTE
PARTS.
- IF REFINISHING, USE A NON-TOXIC FINISH SPECIFIED FOR CHILDREN'S PRODUCTS.
- FOLLOW WARNINGS ON ALL PRODUCTS IN A CRIB.
- READ ALL INSTRUCTIONS BEFORE ASSEMBLING CRIB. KEEP INSTRUCTIONS FOR FUTURE USE.
A STORAGE POUCH & 2 PLASTIC TIES HAVE BEEN PROVIDED IN THE HARDWARE BAG. ATTACH
POUCH TO MATTRESS SUPPORT WITH PLASTIC TIES AND STORE THE INSTRUCTIONS THERE.
- NEVER USE PLASTIC SHIPPING BAGS OR OTHER PLASTIC FILM AS MATTRESS COVERS BECAUSE
THEY CAN CAUSE SUFFOCATION.
- INFANTS CAN SUFFOCATE IN GAPS BETWEEN CRIB SIDES AND A MATTRESS THAT IS TOO SMALL.
- DO NOT USE A WATER MATTRESS WITH THIS CRIB.
- BEFORE USING THIS CRIB, RE-CHECK ALL SCREWS AND BOLTS TO BE SURE THEY ARE
FASTENED SECURELY. A PERIODIC CHECK SHOULD BE MADE TO BE SURE THESE ITEMS REMAIN
TIGHT.
- TO AVOID HEAD INJURY, DO NOT ALLOW ANY CHILD TO PLAY UNDERNEATH CRIB.

·
·
·
·
·
af
·
·
·
a
·
·
·
GENERAL FURNITURE CARE TIPS
Wood, like any natural material is likely to present variations of grain and texture which will result in
slight color variations or richness in the finish. These differences make each Romina Furniture item as
beautiful and unique as you and your baby are.
To preserve the initial appearance and functionality of your furniture, it is recommended that all furniture
items be used in accordance with their intended design.
Special water-based finishes are used to make this furniture safe for your baby. These finishes may be
more delicate than those used on adult furniture thus requiring careful maintenance.
Constant rubbing or mechanical interaction with sharp/hard objects such as belt buckles, jeans' zippers
or buttons will likely damage the finish on your furniture. When placing or retrieving items onto the furniture,
always set them down and pick them up, do not “slide” them. Items placed onto the horizontal surfaces
must be m oved/rotated to prevent discoloration in the finish.
Exposure to extreme variations of environmental conditions such as humidity and temperature can
fect the finish quality due to wood sudden expansion or shrinkage. It is recommended that the room
temperature be maintained in between 65 and 75 degrees Fahrenheit and a relative humidity of 35 – 40 %.
Do not place items which are too hot or too cold directly onto the finished surfaces!
Use caution when using a humidifier or vaporizer. Excessive moisture is harmful to the furniture causing
the finish to peel and the wood to warp.
Wipe up spills promptly. If water or o ther liquids stay in contact with the furniture for a long period of time,
they can cause the finish to turn white or discolor. Alcohol or solvent containing substances or materials will
permanently damage the finish.
In general, furniture should not be placed in front or too close to air-conditioning outlets, fireplaces,
heaters or humidifiers. Direct sunlight and ultraviolet rays will cause colors to fade, affect the luster and
smoothness of the finish and in most cases may cause hairline cracks in the finish. White finishes will
yellow naturally over time; exposure to direct sunlight will accelerate this natural process. Please note that
all wood essences will darken over time along with the natural aging process which is not considered to be
quality defect.
To clean the furniture, use a damp cloth immediately followed by wiping with a dry cloth. Do not allow
water to stay in contact with the finish as it will damage the finish.
If you need to put your furniture into storage for any period of time, avoid placing it in damp basements or
hot attics. Air flow around and under the furniture should be allowed. Do not place furniture too close to
walls, do not stack anything on it and do not cover it entirely.
When using a vinyl changing pad or similar plastic accessories, make sure to use a fabric felt
underneath. Certain plastics have ingredients that can react with and damage the finish. It is
recommended to rotate the changing p ad's position frequently to avoid finish discoloration.

BOX CONTENT NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR MATTRESS
SUPPORT MAY VARY FROM WHAT
IS PICTURED IN THE INSTRCTION
SHEET.
NOTE: The letters by which a part can
be identied represent the initials of
the specic part’s name (this method
is used in order to facilitate parts
recognition between the drawings and
the parts list).
Please locate and conrm that you have the following parts:
FB. footboard = 1 MS. mattress support = 1
HB. headboard = 1 SB. stabilizing bars = 2
LP. left panel = 1 WR. wooden rail = 1
RP. right panel = 1
A bag of hardware containing the following accessories:
1. Allen wrench = 1
2. A storage pouch and 2 plastic ties 6. Round head bolt (15mm - 19/32” = 4
3. Allen bolt (40mm - 1 1/2”) = 2 7. Large “internal star” lock washer = 12
4. Allen bolt (60mm - 2 1/4”) = 8 8. Small “external star” lock washer = 4
5. Allen bolt (100mm - 4”) = 4 9. Wooden cap
NOTE: The item number of your product is
located on the inner side of the left panel, on a
black and white label. Please refer to this number
in the event of needing to contact ROMINA
FURNITURE or your local supplier.
NOTE: During the assembly process, whenever using screws or
bolts, check by using a measuring intrument for each of them, in
order to identify the correct one. Be sure to use the proper size
and shape specied in the instructions. Be sure to COMPLETELY
TIGHTEN the screws and bolts when told to do so.
NOTE: Phillips screwdriver not included!
1
6
3
4
8
7
5
9
LP
RP
MS
SB
WR
HB
FB

NOTE: THE STYLE OF YOUR CRIB,
METALLIC BRACKETS OR MATTRESS
SUPPORT MAY VARY FROM WHAT IS
PICTURED IN THE INSTRCTION SHEET.
SB
SB
LP
RP
STEP 1 (Two adults are required in order to complete this step)
Attach the stabilizing bars (SB) to the left and right panels (LP & RP) of
the crib using 4 medium Allen bolts (4) and 4 washers (7). Align the tenons
attached at the end of the stabilizing bars with the lower holes drilled on the
inner faces of the left and right panels of the crib. Be sure that the drilled
face of the stabilizing bars faces towards the inside of the crib (follow the
instructions attached to the stabilizing bar). Begin turning the bolt clockwise
by hand, in order to ensure the non-stripping of the threads. Afterwards, use
the supplied Allen wrench (1).
Do not completely tighten the bolts at this step, you will be asked to do this
later.
4+7
4+7
4+7
4+7
REQUIRED
FIGURE 1

REQUIRED
MIDDLE POSITION
LOWEST POSITION
HIGHEST POSITION
HIGHEST POSITION
MIDDLE POSITION
LOWEST POSITION
X
X
X
X
Y
Y
Y
Y
STEP 2 (One adult is required in order to complete this step)
There are three di󰀨erent positions for the mattress support (the highest one being intended for a newborn child and the lowest
one for a child that is maximum 35” tall - see cautions note). You must adjust the height of the mattress support (depending on
your child’s height), by inserting all 4 bolts and nuts (Y) in the same position (see FIGURE 2).
Bolts (X) and (Y) are factory mounted.
Do not completely tighten the bolts at this step; you will be asked to do so in a later step.
The mattress support will be assembled in the LOWEST POSITION.
ADJUSTING THE HEIGHT OF THE MATTRESS SUPPORT
To adjust the vertical position of the mattress support, you must remove all four bolts and washers (Y), loosen all eight bolts (4+6,
X), lower the frame and insert the bolts and washers (Y) back into the corresponding holes, according to the desired height (see
FIGURE 2). Afterwards, completely tighten all bolts.
The crib is designed in such a manner that, when the mattress support is adjusted to its lowest position, the mattress
support frame must be placed directly over the bottom frame. Before tightening the bolts, we recommend slightly
pressing down on the mattress support, in order to ensure its correct positioning.
WARNING: IN ORDER TO KEEP YOUR BABY SECURE AND SAFE AND TO AVOID
POTENTIAL INJURY OR DEATH, IT IS VERY IMPORTANT TO COMPLETELY TIGHTEN ALL
12 BOLTS (X), (Y) & (6+8) AFTER ADJUSTING THE HEIGHT OF THE MATTRESS SUPPORT.
WARNING!
COMPLETELY TIGHTEN!
FIGURE 2

LP
WARNING!
TIGHTEN COMPLETELY!
WARNING!
TIGHTEN COMPLETELY!
SB
RP
SB
MS
6+8
6+8
6+8
6+8
STEP 3 (Two adults are required in order to complete this step)
Attach the mattress support (MS) to the stabilizing bars (previously mounted in STEP 1) by using the 4
round head bolts (6), 4 washers (8) and a Phillips screwdriver (which is not included). The lock washer
must be attached to the bolt before inserting it through the metal bracket of the mattress support.
At this point, you must completely tighten all 12 bolts involved in the mattress support xing process, by
using a Phillips screwdriver (which is not supplied).
See Figure 3.
WARNING: IN ORDER TO KEEP YOUR
BABY SECURE AND SAFE AND TO AVOID
POTENTIALINJURY OR DEATH, IT IS VERY
IMPORTANT TO COMPLETELY TIGHTEN
ALL 12 BOLTS LISTED IN STEP 3.
FIGURE 3
REQUIRED

FB
HB
LP
RP
WARNING!
TIGHTEN COMPLETELY!
TIGHTEN THE SAME BOLTS ON
THE RIGHT SIDE OF YOUR CRIB!
4+7
4+7
5+7
5+7
5+7
5+7
FB
LP
RP
SB
MS
metallicinse
rts
metallic inserts
metallicinserts
metallic inserts
4+7
4+7
4+7
4+7
STEP 4 (Two adults are required in order to complete this step)
Take the footboard of your crib (FB) and carefully place it on the oor with the drilled side facing upwards, while being careful
not to scratch its nish. Then, using 4 medium Allen bolts (4), 4 washers (7) and the Allen wrench supplied (1), attach the right
and left panels (RP & LP) as they resulted after completing STEP 3. Be careful to keep the metallic inserts side facing upwards.
Do not completely tighten the bolts at this point, you will be asked to do so later.
STEP 5 (Two adults are
required in order to complete
this step)
Take the headboard of your
crib (HB) and carefully place it
on the part of your crib resulted
after completing STEP 4. Fix it
by using all 4 large Allen bolts
(5), 4 washers (7) and the Allen
wrench supplied (1).
STEP 6
Using the Allen wrench (1)
supplied, you must completely
tighten all 4 medium Allen bolts
(4+7) used to x the stabilizing
bars (see FIGURE 5).
WARNING: IN ORDER TO KEEP YOUR
BABY SECURE AND SAFE AND TO AVOID
POTENTIALINJURY OR DEATH, IT IS VERY
IMPORTANT TO COMPLETELY TIGHTEN
ALL 4 BOLTS LISTED IN STEP 6.
FIGURE 4
REQUIREDREQUIRED
FIGURE 5

WARNING!
TIGHTEN COMPLETELY!
WARNING!
TIGHTEN
COMPLETELY!
5+7
5+7
5+7
5+7 4+7
4+7
4+7
4+7
WARNING: IN ORDER TO KEEP YOUR
BABY SECURE AND SAFE AND TO AVOID
POTENTIALINJURY OR DEATH, IT IS VERY
IMPORTANT TO COMPLETELY TIGHTEN
ALL 8 BOLTS LISTED IN STEP 7.
Once having completed STEP 7, attach
the storage pouch supplied to the mattress
support by using the two plastic ties (also
supplied). Store this instruction booklet in the
storage pouch for further use.
REQUIREDREQUIRED
FIGURE 6
STEP 7 (Two adults are required in order to complete this step)
Turn your crib back on its feet. Using the Allen wrench (1) supplied, you must completely tigten all 8 Allen bolts (4+7) and
(5+7)which remained untightened from all previous steps (see FIGURE 6).
REMINDER
You have a total of 8Allen bolts, distributed as following:
- 4 large bolts (5+7) in the headboard (HB);
- 4 medium bolts (4+7) in the footboard (FB).
this picture shows what you crib should look like after completing the assembly process

4501 VENTIANNI
DAY BED OPTION
ASSEMBLY INSTRUCTIONS FOR THE
WARNING (FOR DAY BED OPTION ONLY):
-ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27 1/4 INCHES BY
51 5/8 INCHES, WITH A THICKNESS NOT
EXCEEDING 6 INCHES.
-THE MINIMUM AGE SHALL NOT BE
LESS THAN 15 MONTHS OLD AND THE
MAXIMUM WEIGHT SHALL NOT BE
MORE THAN 50 LBS.
DO NOT THROW THIS BOOKLET AWAY!
this picture shows what you crib should look like after completing the assembly process
READ ALL INSTRUCTIONS
BEFORE ASSEMBLING THE
CRIB. KEEP THE INSTRUCTION
BOOKLET FOR FURTHER USE.
NEVER USE THE PLASTIC
SHIPPING BAGS OR OTHER
PLASTIC FILM AS MATTRESS
COVERS, AS THEY CAN CAUSE
SUFFOCATION.
MAKE SURE TO SELECT THE
CORRECT SIZE MATTRESS.
INFANTS CAN SUFFOCATE IN THE
GAPS BETWEEN THE CRIB SIDES
AND A MATTRESS THAT IS TOO
SMALL.
THIS CRIB CONFORMS TO APPLICABLE
REGULATIONS PROMULGATED BY
THE CONSUMER PRODUCT SAFETY
COMMISION AND BY THE AMERICAN
SOCIETY FOR TESTING AND MATERIALS.
4300 Northlake Ct, Ste E, Charlotte,
NC 28216
Phone: [phone]
www.rominafurniture.com

pull upwards after removing the Allen bolts
x
x
x
x
MP
STEP A
Using the supplied Allen wrench (1), completely unscrew the 4 Allen bolts (x) (previously mounted in the factory) located 2 by
2 on the lateral sides of the legs. Afterwards, remove the middle panel (MP) by pulling it upwards and then towards yourself
(see FIGURE A). Please store the middle panel and the 4 Allen bolts in a proper place, making sure not to scratch the nish.
Cover the remaining visible holes located on the inner sides of the legs by using the six wooden caps supplied (9).
FIGURE A
REQUIRED

DETAIL B1DETAIL B1
DETAIL C2DETAIL B2
6+8
6+8
6+8
4+7
4+7
STEP B (Two adults are required in order to complete this step)
Carefully take the crib and place it with the footboard (FB) facing towards the oor, making sure not to scratch the nish (see
FIGURE B).
Using the supplied Allen wrench (1) and a Phillips screwdriver (which is not supplied), completely unscrew both Allen bolts
(4+7), which x the stabilizing bar (SB) and both round head bolts (6+8), which x the mattress support (MS) to the front
stabilizing bar.
Rotate the front stabilizing bar by 180 degrees (see the white arrow and the DETAIL B2 for the result).
Adjust the mattress support to its lowest position (see STEP 2).
FIGURE B
REQUIRED REQUIRED

3
3
SB
3
WR
DETAIL C1DETAIL C1
WARNING!
TIGHTEN COMPLETELY!
WR
STEP B (Two adults are required in order to complete this step)
Attach the wooder rail (WR) and x it using both small Allen bolts (3) and the supplied Allen wrench (1).
Rotate the front stabilizing bar (SB) back to its original position and x it using both medium Allen bolts and washers (4+7)
removed earlier.
Fix the mattress support (MS) to the front stabilizing bar by using both round head bolts and washers (6+8) removed earlier.
Completely tighten all the bolts involved in the mattress support and stabilizing bar xing and adjusting process (see STEPS
1 to 3).
Turn your day bed with its feet back towards the oor. The nal product should look like the one depicted on the rst page of
this chapter.
FIGURE C
REQUIRED REQUIRED
WARNING: IN ORDER TO KEEP YOUR
BABY SECURE AND SAFE AND TO AVOID
POTENTIALINJURY OR DEATH, IT IS VERY
IMPORTANT TO COMPLETELY TIGHTEN
ALL THE BOLTS INVOLVED IN THE
MATTRESS SUPPORT AN STABILIZING
BAR FIXING AND ADJUSTING PROCESS
(STEPS 1 TO 3).

4
4
6+8
6+8
6+8
Adjusting the mattress support - STEP 1
Carefully take the crib and place it with the footboard (FB) facing towards the oor, making sure not to scratch the nish (see
FIGURE B).
Using a Phillips screwdriver (which is not supplied), completely unscrew all 4 round head bolts (6+8), which x the mattress
support (MS) to the stabilizing bars.
Adjusting the mattress support - STEP 2
Rotate and pull away the mattress support as shown in
FIGURE E. Adjust the mattress support to the desired
height (See STEP 2 - FIGURE 2).
Adjusting the mattress support - STEP 3
After adjusting the mattress support to the desire height,
slide it back as shown in FIGURE F. Using a Phillips
screwdriver (which is not supplied), completely screw
in all 4 round head bolts (6) which connect the mattress
support (MS) to the stabilizing bars (see FIGURE D).
REQUIRED REQUIRED
FIGURE D
FIGURE E
FIGURE F

NOTE:
YOU CAN ATTACH A TODDLER RAIL TO YOUR
CRIB WITH THE PURCHASE OF ROMINA
FURNITURE ITEM TR 4501 (TODLER RAIL 4501).
ASSEMBLY INSTRUCTIONS FOR THE TODLER
RAIL CAN BE FOUND INSIDE OF THE TR 4501
PACKAGE.
PLEASE CONTACT ROMINA FURNITURE
OR YOUR LOCAL DISTRIBUTOR FOR MORE
INFORMATION ON THE TODLER RAIL.
NOTE:
YOUR 4501 CONVERTIBLE CRIB CAN BE
CONVERTED INTO A FULL SIZE BED WITH THE
PURCHASE OF ROMINA ITEM CODE CKC 4501
(CONVERSION KIT FOR CRIBS, CODE 4501).
THE ASSEMBLY INSTRUCTIONS FOR THE FULL
SIZE BED OPTION CAN BE FOUND INSIDE OF
THE CKC 4501 PACKAGE.
PLEASE CONTACT ROMINA FURNITURE
OR YOUR LOCAL DISTRIBUTOR FOR MORE
INFORMATION ON THE CONVERSION KIT.
4501 VENTIANNI
TODLER RAIL OPTION
(THE TODLER RAIL IS SOLD SEPARATELY)
4501 VENTIANNI
FULL SIZE BED OPTION
(THE CONVERSION KIT IS SOLD SEPARATELY)

CAUTION:
*WHEN A CHILD'S HEIGHT REACHES 35 INCHES, THE CHILD SHOULD BE PLACED IN A YOUTH OR
REGULAR BED.
*USE OFA VAPORIZER NEAR FURNITURE WILL CAUSE WOOD TO SWELLAND FINISH TO PEEL.
*DO NOT STORE CRIB INAREAS WHERE TEMPERATURESAND CONDITIONS ARE EXTREME, SUCH
AS HOT ATTICS OR COLD DAMP BASEMENTS. BOTH OF THESE EXTREME CONDITIONS MAY
CAUSE THE WOOD TO CRACK AND GLUE JOINTS TO LOOSEN RESULTING IN STRUCTURAL
FAILURE.
*SHOULD IT BECOME DESIRABLE TO REFINISH THIS CRIB IN LATER YEARS, THE MANUFACTURER
WARNS THAT ANY MATERIAL USED SHOULD BE NON-TOXIC. REGULAR CLEANING WITH MILD
SOAP ON A SOFT CLOTH, FOLLOWED BY A CLEAN DAMP CLOTH, THEN A DRY CLOTH, WILL
PRESERVE THE ORIGINAL LUSTER AND BEAUTY OF THIS FINE FINISH.
*THIS CRIB IS NOT EQUIPPED TO HANDLE THE EXCESS WEIGHT OFA CRIB WATER MATTRESS.
*LIFT SLIGHTLY WHEN MOVING ON CARPETING TO PREVENT LEG BREAKAGE.
ENSURE A SAFE ENVIRONMENT FOR THE CHILD BY CHECKING
REGULARLY, BEFORE PLACING THE CHILD IN THE CRIB, THAT
EVERY COMPONENT IS PROPERLYAND SECURELY IN PLACE.
MAINTENANCE OF YOUR ROMINA CONVERTIBLE CRIB:
AFTER YOU FINISH ASSEMBLING YOUR CRIB, BE SURE THAT ALL
BOLTS HAVE BEEN TIGHTENED SECURELY. YOU MUST CHECK
ALL BOLTS PERIODICALLY AND RE-TIGHTEN AS NECESSARY
.
PERIODICALLY INSPECT CRIB FOR DAMAGED HARDWARE,
LOOSE JOINTS OR SPLINTERED EDGES.
DO NOT USE CRIB IF PARTS ARE DAMAGED OR BROKEN!
CONTACT YOUR DEALER OR ROMINA FURNITURE FOR
ASSISTANCE AND REPLACEMENT PARTS. PLEASE BE SURE TO
HAVE YOUR MODEL CODE WRITTEN DOWN BEFORE YOU MAKE
CONTACT. THE MODEL CODE CAN BE FOUND ON A WHITE LABEL
LOCATED ON THE INSIDE OF YOUR CRIB ON THE SIDE PANEL.
NEVER SUBSTITUTE PARTS OR MAKE ALTERATIONS TO YOUR
CRIB!

(PAGE INTENTIONALLY LEFT BLANK)

(PAGE INTENTIONALLY LEFT BLANK)

(PAGE INTENTIONALLY LEFT BLANK)

Regular cleaning with mild soap on a soft cloth, followed by a clean damp
cloth, then a dry cloth, will preserve the original luster and beauty of this
fine finish of your Romina Furniture product.
Visit
www.rominafurniture.com
for updates, special offers and more new designs.