Comica CVM-WM100 PLUS User manual

CVM-WM100 PLUS
UHF 1-Trigger-2 Wireless Microphone
User Manual

Technology Parameters
Lavalier Transmitter TX
Channels
Group A Wireless Frequency
Group B Wireless Frequency
Transmitting Power
48
568.125MHz~579.875MHz
580.125MHz~591.875MHz
10dBm /15dBm
Hand-held Transmitter HTX
Channels
Group A Wireless Frequency
Group B Wireless Frequency
Transmitting Power
48
568.125MHz~579.875MHz
580.125MHz~591.875MHz
10dBm /15dBm
Receiver RX
Channels
Group A Wireless Frequency
Group B Wireless Frequency
48
568.125MHz~579.875MHz
580.125MHz~591.875MHz

Contents
1
1
1
2
4
4
5
6
7
8
9
9
13
15
17
17
27
30
41
Foreword
Main Features
Notice
Packing List
Components and Instruction
Lavalier Transmitter
Hand-held Transmitter
Receiver
Button Instruction
Indicator Light Instruction
Installation and Usage
Preparation Before Usage
Transmitter Installation
Receiver Installation
Screen Display and Operation
Lavalier Transmitter
Hand-held Transmitter
Receiver
Specification

Foreword
Main Features
. 1-Trigger-2, Perfectly Support Two Transmitters and One Receiver Work Simultaneously
. Working Distance Up to 100m (Open Area 100m, 60m in Area with Obstacle)
. Auto-scanning and IR Sync for Quick Channel Selection
. M/S Switch, LCF, 16-Levels Adjusted Gain Control, Muting Functions
. AA Batteries and External Power Supply
. Support Real-time Monitor
. Volume Dynamic Monitor
. Adjusted RF Power
. Lattice LCD Display, High Resolution
Notice
Thanks for purchasing COMICA WM100 PLUS wireless microphone.
To ensure the smooth use and safety of the product, please carefully read this
instruction before using and properly assemble and operate.
Transmitter should be used more than 10cm from Receiver, when the distance is
less than 10cm, Receiver’s wireless signal receiving part will take protect action
to shut down wireless signal receiving, then audio may be intermittent, which is
normal;
When using auto IR sync, please stay within 30cm, otherwise the signal may be
so weak that the sync will not be successful;
In the case of stereo/mono mode switch, please preset the mode before using to
avoid the transient interference caused by switching during usage;
The antenna will affect the working distance. Please protect the antenna and
avoid any man-made damage;
The working distance will be affected by the surrounding environment. Please try
to keep the environment open without interference during usage, and turn off the
WIFI nearby;
When using this product in a short distance, it is recommended to set RF strength
at ‘LOW’ to reduce the power consumption;
For smartphone shooting, customers must separately purchase a TRS-TRRS
audio converting cable, and pay attention to set the mobile phone mode to 'Flight
Mode' to avoid incoming call interference(It does not support the partial Default
Video Mode of android systems, the third-party APP is recommended to be used
in this case);
Do not expose the device in rain or humid environment, otherwise there will be a
danger of short circuit;
Please keep this product in dry environment;
1

Main Parts:
Packing List
Lavalier Transmitter (TX) Receiver (RX)
Hand-held Transmitter (HTX)
Purchase Options:
WM100 PLUS HTX:
WM100 PLUS(A) = 2TX + RX
TX TX RX
++
WM100 PLUS(C) = TX + RX
TX RX
+
2

Accessories:
3.5mm Mic Audio Input Cable
3.5mm-3.5mm Audio Output Cable
3.5mm-XLR Audio Output Cable
Belt Clip
Camera Mount
Wind Muff
1
2
3
4
5
6
11
USB Power Input Cable
Portable Bag
User Manual
Certification
Warranty Card
7
8
9
10
1
1
6
2
7
3
8
4
91110
6 7 8 9 10
5
2 3 4 5
1 6 7 8 9 10
11
11
2 3 4 5
WM100 PLUS(A) = X2 + X2 +X3 ++ + + + ++
WM100 PLUS(C) = X2 +++ + ++ + +
+
++
The accessories of each combination include:
3

Components and Instruction
14
1
2
3
4
5
9
10
12
13
11
6
8
7
Components
Lavalier Transmitter (TX)
Antenna
Working Status Indicator
On-off / Muting Button
SET Function Menu
Function Selection Button -
LINE IN External Input
IR Sensor
Mic External Input
IR Status Indicator
Function Selection Button +
Micro USB Port for External Power Supply
Belt Clip
1/4 Thread
Battery Tray
1
2
3
4
5
6
7
8
9
10
11
12
13
14
4

Microphone
LCD Display
Power / Muting Button
IR Screen
Low Cut Filter/Normal Audio Switch
Signal Strength “High/Low” Switch
Hand-held Transmitter (HTX)
1
2
3
4
5
6
2
1
3
4
65
LCF
-
RF
High
Low
LCF
RF
5

1
3
4
5
6
2
10
11
13
14
15
12
7
9
8
Receiver (RX)
Group A Antenna
Group B Antenna
Group A Working Status Indicator
On-Off Button
SET Function Button
Function Selection Button -
3.5mm Audio Input Jack
IR Sensor
3.5mm Monitoring Jack
Group B Working Status Indicator
Function Selection Button +
Micro USB Port for External Power Supply
Belt Clip
1/4 Thread
Battery Tray
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
6

Lavalier
Transmitter
/ Receiver
Power / Muting Button
Long Press
Short Press
Power On / Off
Muting Mode
( It is available only when
light up the screen)
SET Function Menu
+ Button
- Button
Long Press
Enter the function
adjustment menu
Short Press
Short Press
Short Press
1.Confirm the selected
function
2.Exit the function
adjustment menu
Function Adjustment (+)
Function Adjustment (-)
Function Button Instruction
Hand-held
Transmitter
Power / Muting Button
“Low cut/ Normal”
Sound Switch
Signal Strength
“High/Low”
Switch
Long Press Power On / Off
Short Press
Muting Mode
( It is available only when
light up the screen )
Push-up Signal strength--high
Push-down Signal strength--low
Push-up Low cut
Push-down Normal
LCF
-
RF
High
Low
7

Indicator Light Instruction
Low cut function:
Cut the low frequency part and reduce the noise to make the sound
more clear.
Signal strength high/low switching effect:
With high signal strength, the working distance is up to 60-100m,
but high power consumption bring short battery life.
With low signal strength, the working distance is up to 30-60m,
but low power consumption bring long battery life.
A IR/RF: Group A Working Status Indicator
B IR/RF: Group B Working Status Indicator
Transmitter
Receiver
RF
A IR/RF
B IR/RF
IR
Green Light Keeps On
Green Light Keeps On
Green Light Keeps On
Red Light Keeps On
Red Light Flicker
Red Light Flicker
Red Light Flicker
Red light keeps on
Green Light Flicker
Normal Recording Status
(This state is only for the
transmitter, when the
channel matches
successfully, the receiver
can pick up the sound)
Muting Mode
Low-power reminder
Channel matches
(No matter the channel
matches or not)
Channel in the match...
(only for IR Sync)
Normal working status after
the channel matches
Channel doesn’t match
Channel in the match...
(only for IR Sync)
Low-power reminder
Group closed
8

Installation and Usage
1.1 Install two AA batteries into the battery tray according to their
positive and negative electrode
1. Prepare Power Supply
There're two ways of Power Supply, you can optionally choose AA
batteries or External Power
Preparation Before Usage
(Transmitter Operating Steps same with Receiver)
9

1.2 External Power Supply
Insert micro USB cable to the USB charging port to realize
external power supply
Micro USB
POWER
When it takes a long time to
use, external mobile power
supply can be used instead
of AC-DC power supply,
otherwise noise will be
introduced
10

1.3.Belt Clip Installation
Please install the belt clip according to the illustration
11

Please refer to screen operation instruction for channel matching.
2.2 Long press the button switch to turn on
the hand-held transmitter
2.3 After the channel matched with the receiver, it can be used
2. Hand-held Transmitter
2.1 Install two AA batteries into the battery tray
according to the positive and negative electrode
AA AA
12

3.1 Insert the 3.5mm audio input cable into MIC socket
3.2 Long press the power button to turn on the transmitter
3. Lavalier Transmitter Installation
13

H
A
Group A
A
3.3 Target the MIC to the audio source and check the working status
according to the volume indicator on the screen
3.4 After the channel matching with the receiver, it can be used
Audio Dynamic Display Bar
570.875MHz
Please refer to screen operation instruction for channel matching.
14

4.1 Connect receiver to your video equipment through the camera
mount
4. Receiver Installation
4.2 Connect the receiver to the camera or camcorder through the
3.5mm-3.5mm audio output cable, plug the headphone into the
3.5mm monitoring interface for real-time monitoring, then long press
the power button to turn on the receiver
Most DSLR cameras has 3. 5mm port, if you use the XLR camcorder,
you need to use the 3. 5mm-XLR audio output cable.
15

3.5mm-XLR Audio
Output Cable
3.5mm-3.5mm
Audio Output Cable
3.5mm Audio Output
Monitoring Cable
Please refer to screen operation instruction for channel matching.
4.3 After the channel matching with the receiver, it can be used
16