Airspan AS4000 Guide

605-0000-454 Draft Issue 1.3 Date 8/02/00
AS4000
Wireless Local Loop System
Subscriber Terminal
Installation and Commissioning

AS4000 Subscriber Terminal
Installation and Commissioning Preface
605-0000-454
Draft Issue 1.3 Date 8/02/00
Page 2of 2
This Page Intentionally Blank

AS4000 Subscriber Terminal
Installation and Commissioning Preface
605-0000-454
Draft Issue 1.3 Date 8/02/00
Page 3of 3
Notice
1. This manual is subject to revision.
2. All rights reserved.
3. Right of modification reserved.
4. This manual is supplied without liability for errors or omissions.
5. No part of this manual may be reproduced or used except as authorised by contract or
other written permission.
6. This equipment is conditioned by the requirement that no modifications will be made to
the equipment unless the changes or modifications are expressly approved by ACC
Communications
7. Prerequisite skills: Personnel installing, commissioning, and maintaining the Airspan
products must have a basic knowledge of telephony and radio communications, and
have experience in installing, commissioning and maintaining telecommunications
products. ACC provides a range of comprehensive training courses specifically aimed
at providing operators/users of Airspan products with the prerequisite skills to install,
commission and or maintain the product. The courses can be tailored to provide the
level of training required by the operator/user.
8. Airspanand Sitespanare Registered Trademarks of Airspan Communications
Corporation.
For additional information on Airspan Systems, please call your ACC Representative, or
contact ACC at: Cambridge House
Oxford Road
Uxbridge
Middlesex
UB8 1UN
Call (44) 1784 886700

AS4000 Subscriber Terminal
Installation and Commissioning Preface
605-0000-454
Draft Issue 1.3 Date 8/02/00
Page 4of 4
This Page Intentionally Blank

AS4000 Subscriber Terminal
Installation and Commissioning Preface
605-0000-454
Draft Issue 1.3 Date 8/02/00
Page 5of 5
SAFETY INSTRUCTIONS - WARNINGS AND CAUTIONS
SAFETY
1. Read and follow all warning notices and instructions marked on the product or included in
this manual
2. Do not allow anything to rest on the power cord and do not locate the product where
persons could step or walk on the power cord.
3. When installed in the final configuration, the product must comply with the applicable Safety
Standards and regulatory requirements of the country in which it is installed. If necessary,
consult with the appropriate regulatory agencies and inspection authorities to ensure
compliance.
4. No hazardous RF radiation is emitted from the equipment. Measured at the surface of
the CRU radome, when transmitting, the maximum total power radiated from the CRU is
0.01% of the UK National Radiological Protection Board basic restriction per kg. of body
part.
WARNING - HAZARDOUS VOLTAGES
On AC installations, hazardous voltages exist. Use caution when verifying or working with
AC power. Remove metal jewellery that could come into contact with AC power.
On DC sections, short circuiting the low voltage, low impedance circuits can cause severe
arcing that may result in burns or eye damage. Remove rings, watches etc. to avoid shorting
DC circuits.
Electro-Static Discharge ESD
Electro-Static Discharge. Many circuits contain devices which are susceptible to damage from
high impedance voltage sources. To avoid such risks always follow anti-static procedures
where marked.

AS4000 Subscriber Terminal
Installation and Commissioning Preface
605-0000-454
Draft Issue 1.3 Date 8/02/00
Page 6of 6
NOTE
Airspan products do not contain hazardous substances (as defined in UK ‘Control of
Substances Hazardous to Health Regulations 1989’, and the ‘Dangerous Substances
Regulations 1990’). At the end of any Airspan product’s life cycle, the customer should
consult with ACC to ensure that the product is disposed of in conformance with the relevant
regulatory requirements
The Symbol on an Airspan product signifies that it has been certified according to the EMC
directive 89/336/EEC. The product fulfils the requirements according to the following
standards:
EN50082-1 for Immunity.
EN55022 Group 1 Class A for the Central Terminal Emissions.
EN55022 Group 1 Class B for the Subscriber Terminal Emissions.
NOTE
The Subscriber Terminal equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules.

AS4000 Subscriber Terminal
Installation and Commissioning Preface
605-0000-454
Draft Issue 1.3 Date 8/02/00
Page 7of 7
User Response Form
Mail: Airspan Communications Limited Fax: [phone]
Oxford Road
Uxbridge
Middlesex
UB8 1UN
Document Rating Excellent Good Average Below Average Poor
Accuracy / Completeness qqqqq
Clarity / Organisation qqqqq
Figures qqqqq
Table of Contents/Index qqqqq
The nature of this response is Addition qDeletion qCorrection q
Please enter details of response below (include precise reference to Section, Page, Paragraph)
Please Complete the following for acknowledgement/response:
Name: ........................................ Address ..........................................
Company ........................................ ..........................................
Job Title ........................................ ..........................................
Department ........................................ ..........................................
Telephone ........................................ ..........................................
Thank you for your co-operation and assistance.

AS4000 Subscriber Terminal
Installation and Commissioning Preface
605-0000-454
Draft Issue 1.3 Date 8/02/00
Page 8of 8
This Page Intentionally Blank

AS4000 Subscriber Terminal
Installation and Commissioning ICL 001
605-0000-454
Draft Issue 1.3 Date 8/02/00
Page 1of 2 © Copyright Airspan Communications Corporation 2000
ISSUE CONTROL LIST
Title Issue Date Issue Details
Title Page Draft 1.3 February 2000
ICL-001 Draft 1.3 February 2000
IXL-001 Draft 1.3 February 2000
GSI-001 Draft 1.3 February 2000
GSI-002 Draft 1.3 February 2000
GSI-003 Draft 1.3 February 2000
DLP 001 Draft 1.3 February 2000
DLP 002 Draft 1.3 February 2000
DLP 003 Draft 1.3 February 2000
DLP 004 Draft 1.3 February 2000
DLP 005 Draft 1.3 February 2000
DLP 006 Draft 1.3 February 2000
DLP 007 Draft 1.3 February 2000
DLP 008 Draft 1.3 February 2000
DLP 009 Draft 1.3 February 2000
DLP 010 Draft 1.3 February 2000
DLP 011 Draft 1.3 February 2000
DLP 012 Draft 1.3 February 2000
DLP 013 Draft 1.3 February 2000
DLP 014 Draft 1.3 February 2000
DLP 015 Draft 1.3 February 2000
DLP 016 Draft 1.3 February 2000
DLP 017 Draft 1.3 February 2000
DLP 018 Draft 1.3 February 2000

AS4000 Subscriber Terminal
Installation and Commissioning ICL 001
605-0000-454
Draft Issue 1.3 Date 8/02/00
Page 2of 2
CHANGE TYPE/DATE PURPOSE PAGES AFFECTED
Draft Issue #, Month
Year
1.2 July 1999 Wall Mounting
Bracket Installation
Procedure Changes
DLP-015
1.3dr February 2000 ST V2 Removed
Modular added
DLPs Removed and
Renumbered