Comind SS Series User manual

USER MANUAL
BOOTS DRYER
LINE SS

www.comindindustries.com
www.comind.cl
1. General Information
This manual prepared and distributed by Comind Industries is intended to convey
recommendations, warnings and requirements regarding your purchase and use of the
products described below. Visit the Comind Industries website (https://www.comind.cl/) or
contact Comind customer service for further product information. To ensure proper use of
the equipment, the user should carefully review this Manual.
FAILURE TO COMPLY WITH THE INFORMATION PROVIDED IN THIS MANUAL IMPLIES THAT
THE USER ASSUMES ALL RISKS AND LIABILITIES ARISING FROM SUCH FAILURE.
SAFETY INSTRUCTIONSNOTE: Boot dryers are designed and manufactured for use in
heating boots of various sizes.NOTE: Operating current is important for the user to calculate
in order to properly size the power cord and other components for safe operation of the
equipment.
SAFETY STATEMENTSThe user must ensure that the installer uses all relevant PPE
(personal protective equipment) when executing the equipment.
This product is not designed for use in classified (hazardous, ATEX) locations.








www.comindindustries.com
www.comind.cl
2. Technical Specifications
The equipment is made of SU304 stainless steel,
with high speed fan and constant temperature
heating module.
Special design for storing various boots, shoes,
etc. It has multiple openings to realize complete
and uniform drying by multifunctional controller.
Ozone disinfection can effectively sterilize and
prevent the reproduction of bacteria, eliminating
the odor inside the boots.
Technical Data
SS 10 PAIRS SS 20 PAIRS SS 40 PAIRS
1 KW 1.1 KW 2.2 KW
23 KG 50 KG 104 KG
760*600*1640 MM 1360*600*1640 MM 1380*750*1900 MM
MODEL:
PRODUCT SIZE:
POWER:
NET WEIGHT:
SCAN AND DOWNLOAD
OUR MANUAL
0 - 60 °C 0 - 60 °C 0 - 60 °C
TEMPERATURE RANGE:
220 V 220 V 220 V
VOLTAGE:

1. In standby or manual mode: press and hold "Time Set" for 1 second to enter the
setting system, then press "Up "or "Down "to modify the clock according to the time
zone and finally press "Time Set.
2. In manual mode: press and hold "Temp Set" for 1 second to enter manual
temperature setting, adapt it to your needs and press "Temp Set" to exit
(Recommended use between 42°C and 45°C).
www.comindindustries.com
www.comind.cl
3. Installation
BEFORE INSTALLING
Inspect for any damage that occurs during shipping, storage or handling.
MOUNTING DIRECTION
The assembly of our boot dryers must be wall mounted. Take care of the electrical
components on the back side of the product. Ensure a minimum distance of 30 cm from
the wall.
1.Adjust the thermostat to ensure proper operation of the equipment.
2.Adjust the temperature and drying time.
3.The control panel works as follows:


4. Temperature Control
Manual Mode

www.comindindustries.com
www.comind.cl
5. Reference Images and Drawings
Modelo SS 10 Pairs
Modelo SS 20 Pairs
Modelo SS 40 Pairs
760 mm 600 mm
1640 mm
1640 mm
Modelo SS 20 pares
Modelo SS 40 pares
1360mm
1900 mm
750 mm1380 mm
760 mm 600 mm
1640 mm
1640 mm
Modelo SS 10 pares
Modelo SS 40 pares
1360mm 600 mm
1900 mm
750 mm1380 mm
760 mm 600 mm
1640 mm 1640 mm
Modelo SS 10 pares Modelo SS 20 pares
1360mm 600 mm
1900 mm
750 mm1380 mm

www.comindindustries.com
www.comind.cl
The maintenance of the equipment must be performed by COMIND INDUSTRIES
personnel. If your company is located far from the headquarters area, it is
recommended to contact your assigned executive to manage the steps to follow.
Note: Do not allow water to enter the control panel.
HOW TO ORDER SPARE PARTS
If you do not know your Comind representative, visit our website http://comind.cl and
use the Where to Buy tool. To order your spare part, please indicate the product numbers
so that the salesperson can find the manufacturing route of your equipment.
COMIND Industries warrants these products to be free from defects in materials and
workmanship for a period of 6 months from the date of shipment. If this product proves
defective during its warranty period, COMIND will repair the product at no additional
charge, or provide a replacement in exchange for the defective product.
This warranty shall not apply to any defect, failure or damage caused by improper use or
maintenance.
1. The recommended drying temperature is 42°C-45°C. When the temperature is
adjusted too high, please do not touch the surface of the stainless steel equipment
with your hands to prevent burns.
2. Do not wash the control panel directly with water.
3. If the equipment needs to be repaired, please cut off the power supply. And please
professional maintenance
4. The appliance is not to be used by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
5. Children being supervised not to play with the appliance.
6. Matters needing attention
7. Inspection and Maintenance
8. Warranty
Modelo SS 20 pares
600 mm