Comm Net Systems v30/30 Manual instruction

SETUP AND OPERATION MANUAL
FOR TELECOM BROADBAND
v30/30 Distribution Panel

Comm/net Systems, Inc.
4237 – 24th Avenue West
Seattle, WA 98199
TEL: [phone]
FAX: [phone]
www.commnetsystems.com
24/7 Sales & Service
To purchase Comm/net Systems solutions, contact your
Comm/net Systems representative at: [phone]
or e-mail: [email protected]
About Comm/net Systems
Comm/net Systems, Inc. (CSI) is the leader in high power density communications power
systems. Comm/net offers comprehensive power and communications site systems integration
and deployment services via a national footprint of regional branch offices. Additional
information can be found at www.commnetsystems.com.
© 2018 Comm/net Systems, Inc. All rights reserved. Comm/net Systems, and the Comm/
net Systems logo are registered trademarks of Comm/net Systems, Inc. in the United States
and other countries. All other trademarks, service marks, registered marks, or registered
service marks are the property of their respective owners. Comm/net Systems assumes no
responsibility for any inaccuracies in this document. Comm/net Systems reserves the right to
change, modify, transfer, or otherwise revise this publication without notice.
Document Number: 048-781-30
Revision Level: r01
Published: July 2018

SETUP AND OPERATION MANUAL
FOR TELECOM BROADBAND
v30/30 Distribution Panel

V30/30 DISTRIBUTION PANEL
SETUP AND OPERATION MANUAL
ABOUT THIS MANUAL
About This Manual
To reduce the risk of damage to equipment, injury, or death; and to ensure proper
installation and operation of Comm/net Systems products, please be sure to read and
understand the entirety of this manual and any other supplied documentation. Keep
this document in a safe and accessible place for future reference.
Safety and Alert Symbols
The following symbols may appear in this manual, other supplied documentation, or on Comm/net Systems product labeling. The meaning of
this indication is explained below.
NOTICE
INDICATES IMPORTANT INFORMATION REGARDING THE COMPLETE AND PROPER FUNCTION OF A PRODUCT.
TYPICALLY REFERS TO MONITORING CONFIGURATION OR OTHER NONDANGEROUS SITUATIONS.
CAUTION
INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD DAMAGE
EQUIPMENT/PROPERTY OR COULD RESULT IN MINOR OR MODERATE INJURY.
WARNING
INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, COULD RESULT IN INJURY OR DEATH.
DANGER
INDICATES A HAZARDOUS SITUATION WHICH, IF NOT AVOIDED, WILL RESULT IN SERIOUS INJURY OR DEATH.
Product support
If you have any questions concerning Comm/net Systems products and services, contact our support staff. Our knowledgeable support team
can provide product technical support and answer other questions regarding Comm/net products and services.
In addition to contacting Comm/net Support directly via phone or e-mail, our online help desk is available 24 hours a day, 7 days a week. The
help desk includes answers to commonly asked questions and self-help articles as well as an online ticket submission system if you need to
contact Comm/net after normal business hours.
yComm/net support is available by phone or e-mail Monday – Friday from 8am – 4:30pm Pacific Standard Time.
yThe online web portal is available 24/7 to submit support requests and general questions, or view the FAQ and self-help articles.
NOTE: All questions submitted to the web portal will be answered during normal business hours.
yPhone: 1-800-274-0544
yE-mail: suppor[email protected]
yOnline Web Portal: https://commnetsystems.freshdesk.com

V30/30 DISTRIBUTION PANEL
SETUP AND OPERATION MANUAL
TABLE OF CONTENTS
Table of Contents
Section 1: Purpose and Applicability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1.1 Product Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Section 2: Theory of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2.2 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Section 3: Unpacking and Inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3.1 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Section 4: Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.1 Installation Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.1.1 Elevated Operating Ambient Temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.1.2 Reduced Air Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.1.3 Mechanical Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.1.4 Circuit Overloading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.1.5 Reliable Earthing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.1.6 Disconnect Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
4.2 Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.3 Chassis Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
4.4 Input Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.5 Alarm Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.6 Installing The Network Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.7 Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.8 Breaker Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.9 Polarity Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.10 Display Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.11 Installation Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Section 5: Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1.1 Firmware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1.2 Firmware Icons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.2 Home Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2.1 Bus Load and Voltage Displayed Per Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2.2 Display Per Breaker Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.2.3 Alarm Indication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5.3 Module Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.3.1 Individual Breaker Load and Ampacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.3.2 Breaker Detail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.4 Bus Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.4.1 Bus Load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.4.2 Bus Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.5 System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.5.1 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.5.2 Touch Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.5.3 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.5.4 Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.6 Advanced . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.6.1 Raw Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.6.2 Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.6.3 Test Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.6.4 Restore Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
5.7 Review System Status via the Embedded Web Server . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.7.1 Default Static Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.7.2 Real-time Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
5.7.3 Administration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Section 6: Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Appendix A: Mechanical Drawings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Appendix B: Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appendix C: Supported Lugs for Termination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appendix D: Supported Slimline Bullet Circuit Breakers. . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Appendix E: Output Cable Whips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Appendix F: One-Line Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

V30/30 DISTRIBUTION PANEL
SETUP AND OPERATION MANUAL
PAGE VI -
THIS PAGE INTENTIONALLY LEFT BLANK

V30/30 DISTRIBUTION PANEL
SETUP AND OPERATION MANUAL
PURPOSE AND APPLIcABILITy - PAGE 1
Section 1: Purpose and Applicability
The purpose of this document is to detail the installation and operation instructions
for the V30/30 distribution panel.
1.1 Product Model
This document applies to the following models of the
Comm/net Systems, Inc.® V30/30 distribution panel:
TABLE 1. V30/30 DISTRIBUTION PANEL MODEL
PART NUMBER DESCRIPTION
016-2121-10 V30/30 Distribution Panel
Section 2: Theory of Operation
2.1 Introduction
The V30/30 product family consists of a dual-input 30A/30B breaker position, 4RU
distribution panel with 40A connectorized outputs and an advanced touch screen
display. Breakers are available for this panel in ratings from 2 ampere up to 30 ampere.
2.2 Features
yModular design
y4RU; 19" or 23" rack compatible*
y2A and 2B inputs; 300A each
yUp to (60) breaker positions (30A/30B)
yUp to (6) distribution modules with (10) breaker positions each
yModules are dual input with (5) breaker positions per side (5/5); 150A
maximum current per module input
y35A maximum current per breaker position
yConnectorized outputs
yLCD touchscreen controller with Ethernet (HTTP; SNMP)
yOptional per-circuit current monitoring and RedundancyTracker™
yUnmatched safety and reliability
*23" rack ear kit required.
Figure 1. V30/30 Distribution Panel

V30/30 DISTRIBUTION PANEL
SETUP AND OPERATION MANUAL
PAGE 2 - PURPOSE AND APPLIcABILITy
THIS PAGE INTENTIONALLY LEFT BLANK

V30/30 DISTRIBUTION PANEL
SETUP AND OPERATION MANUAL
UNPAckING AND INSPEcTION - PAGE 3
Section 3: Unpacking and Inspection
The Comm/net Systems V30/30 distribution panel was carefully packaged at the
factory to withstand the normal rigors of shipping. However, you should carefully
inspect the box and contents to confirm that no damage has occurred in transit. Most
shipping carriers require notification of shipping damage within twenty-four hours of
delivery, and it is the responsibility of the recipient to inspect the shipment immediately
upon receipt.
3.1 Package Contents
Included with your product are the following items:
yV30/30 distribution panel
yBreaker module assemblies (up to 6 per panel)
yMounting hardware kit with necessary screws and washers
Section 4: Installation
4.1 Installation Preparation
When selecting an installation location, ensure that all of the following conditions are
met before proceeding.
4.1.1 Elevated Operating Ambient Temperature
If you install the panel in a closed or multi-unit rack assembly, the operating ambient
temperature of the rack environment may be greater than room ambient. Therefore,
take care to install the equipment in an environment compatible with the maximum
ambient temperature (TMA) specified in Section 6.
4.1.2 Reduced Air Flow
Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised.
4.1.3 Mechanical Loading
Mounting of the equipment in the rack should be such that a hazardous condition is
not achieved due to uneven mechanical loading.
4.1.4 Circuit Overloading
Give consideration to the connection of the equipment to the supply circuit and
the effect that overloading of the circuits might have on overcurrent protection and
supply wiring. Use appropriate consideration for equipment nameplate ratings when
addressing this concern.
4.1.5 Reliable Earthing
Maintain reliable earthing of rack-mounted equipment. Pay particular attention to
supply connections other than direct connections to the branch circuit (e.g., use of power
strips).
4.1.6 Disconnect Device
A readily accessible disconnect device must be incorporated in the building
installation wiring.

V30/30 DISTRIBUTION PANEL
SETUP AND OPERATION MANUAL
PAGE 4 - INSTALLATION
4.2 Mounting
NOTICE
THIS PRODUCT MUST BE INSTALLED WITHIN A RESTRICTED
ACCESS LOCATION WHERE ACCESS IS THROUGH THE USE
OF A TOOL, LOCK AND KEY, OR OTHER MEANS OF SECURITY,
AND IS CONTROLLED BY THE AUTHORITY RESPONSIBLE
FOR THE LOCATION. THIS PRODUCT MUST BE INSTALLED
AND MAINTAINED ONLY BY QUALIFIED TECHNICIANS.
Step 1. Attach the (3) cable lacing bars to the threaded inserts found on the rear of the
chassis using the included 12-24 hardware (see Figure 2).
Step 2. Secure panel to equipment rack by tightening the included 12-24 hardware
into the mounting ears (see Figure 3).
4.3 Chassis Ground
CAUTION
DO NOT ENERGIZE THE PANEL BEFORE
CHASSIS GROUND IS CONNECTED.
The chassis ground is located in the side of the panel. A two hole lug landing position
is provided. See table below for termination information. A minimum of #6 AWG chassis
ground cable is required.
IMPORTANT: Grounding hardware not included. A properly-sized grounding
conductor must be installed per NEC (250.122).
TABLE 2. CHASSIS GROUND TERMINATION SPECIFICATIONS
TERMINATION
TYPE
HOLE/STUD
SIZE CENTER TO CENTER
RECOMMENDED TORQUE
VALUE
Threaded Insert 1/4 in. 5/8 in. 75 in∙lbs
Step 1. Secure the ground cable to the chassis by tightening 1/4 in. hardware (see
Figure 4).
Figure 3. Rack Install
Figure 2. Lacing Bars
Figure 4. Chassis Ground