Command access PD10-M-CVR User manual

PD10-M-CVR
Doc # 20201_C
1
INSTALLATION INSTRUCTIONS
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
A.
PD10-M-CVR Includes
A. Head Cover pack
B. CVR Exit Device
C. Concealed Vertical Rods
D. Hinge Stile End Cap pack
E. Strike pack
F. Retractor & Pinion pack
G. Traveler pack
H. MM4 - Installed in exit device
I. 6’ Power Lead
Tools Required
• Cordless Drill
• Needlenose Pliers
• Measuring Tape
• 1/2 Drill bit
The PD10-M-CVR is a storefront grade 1 exit device equipped with motor drive latch retraction. Retrots
Doromatic 1690 & First Choice 3690.
B.
D. E. F.*
C.
G.*
H.
I.
*Certain parts may already be attached to rods

2
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
TECHNICAL INFORMATION
Specications
PTS Video
Click or Scan
• Input Voltage: 24VDC +/- 10%
• Average Latch Retracon Current: 1 Amp
• Average Holding Current: 125 mA
• Wire gauge: Minimum 18 gauge
Step 1-Press the device push pad to the desired seng. (this can be fully
depressed or less than fully depressed).
Step 2- While depressing the push pad, apply power. (i.e. presenng the
credenal to the reader).
Step 3- Connue to keep pad depressed, the device will beep 6 mes, roughly
5 seconds. Aer the beeps have stopped, release the pad and now the
adjustment is complete. If not to your liking repeat the three steps. That’s
all there is to it.
Setting PtS
2 Beeps
3 Beeps
5 Beeps
6 Beeps
7 Beeps
BeePS exPlanation Solution
Over Voltage
Under Voltage
Forced Release
Push pad is depressed. Device is
re-adjusng
Over-travel or mechanical
obstrucon
> 28V unit will shut down. Check voltage & adjust to 24 V.
< 22V unit will shut down. Check voltage & adjust to 24 V.
Device will automacally re-engage within 5 seconds.
Check to make sure the push pad is not stuck or catching on
anything.
trouBleShooting & DiagnoSticS
4 Beeps Failed Sensor Verify all 3 sensor wires are installed correctly. Replace sensor if
problem persists by contacng CAT tech support.
If mechanical obstrucon, remove & push pad down unl
beeping stops to reset. If no obstrucon, the pad may have
been pushed in too far during PTS calibraon. Recalibrate
with the pad slightly out. If problem persists, verify the
magnet is within 1/4” of the sensor at the end of travel.
**Important Info**
Make sure to set PTS before nishing installaon!

3
Electried Exit Device
Installation Example
Module
Ceiling Tile
Legend
Optional Module
Placement
Standard Placement
Optional Placement
Module
GREEN
CHANNEL 1
LED
NORMALLY OPEN
DRY CONTACT FROM
ACCESS CONTROL
SYSTEM
NO VOLTAGE
LOCKING
HARDWARE
+
-
CAT
RECOMMEND POWER SUPPLIES:
All Command Access exit devices & field installable kits have been thoroughly cycle tested with
Command Access power supplies at our factory.
• PS210
• PS220/220B
• PS440B
• PS480B
• PS1
• PS2/2B
• PS5-4
• PS5-6
For more informaon click here or go to our website

4
Concealed Vertical Rod
For Bottom Rod Latch
Installation Template
All prep is shown on interior side of the door,
except where noted.
Right hand door shown. (LHR)

5
(Rods are factory preset for door height of 83 3/16 and a cylinder location of 41 5/16- see page 9 for
additional details.)
Install top latch mechanism using 2 ea.
#10-31X1/4 screws.
Install bottom rod assembly in the same
manner as above.
Ax bent end of rod on door using rod
bushing with “E” ring.
Pic 3
STEP 1 - Install Vertical Rods
A.
B.
C.
Install the stile mounting bracket with 2 ea.
1/4-20 x 1/2 pan head screws. Leave space to
capture the base of the device. (See next slide)
A.
STEP 2 - Mount Exit Device

6
Slide the end of baserail underneath the
mounting bracket.
Attach head of device to stile with 2 ea.
1/4-20x1/2 at head screws. Tighten
screws on the head and tail of the device.
B.
C.
Remove lock stile end cap.
STEP 3 - Drill Wire Chase
A.

7
Slide push pad o of baserail.
Drill the hole for our 2 pin power lead in-
between the 2 mounting screws.
B.
C.
Feed the 2 pin power lead into the hole
and connect to our MM4 module. Also,
make sure to clean out any debris left.
D.
Debris
Note: Depending on where your power transfer is; next you would sh the other side of the power lead we
connected to the MM4 and hook up to your incoming power. If you have a portable tester this would be a
good time to test re the motor.

8
Before installing the traveller. Remove Axle
screw, allowing the lifting arm to relax and
move out of the way.
Replace push pad, making sure the
activating brackets and pins slide through
the 3rd channel.
STEP 4 - Attach Vertical Rods
E.
Reinstall the lock stile end cap.F.
A.

9
Install Pinion support bracket and tighten
retainer screw.
Re-install Axle screw and tighten.
Install Traveller onto the bent end of the
vertical rods.
B.
C.
D.

10
Reinstall Axle screw and tighten.
Add Retractor and Traveller lift bracket. Pick
placement of pinion depending on desired
function.
Place Pinion with black cylinder bushing into
the door with the cylinder tail piece sliding into
the back of the pinion.
Flat side of pinion facing up.
Optional STEP - Installing Cylinder
B.
C.
A. Flat Side

11
-Check Bottom Rod operation.
The bottom latch should not protrude more
than 1/16 inch below the bottom of the door
when the push pad is depressed.
-Check Top Rod operation.
When push pad is depress fully, top latch should
open and allow top strike to pass, and swing
freely.
Install Pinion support bracket and tighten
retainer screw.
D.
STEP 4 - Continued
B.
A.
Install head cover with 2 ea. 10-32 x 3/8
screws.

12
Remove the Axle screw and lifting arm.
Flip the lifting arm to the other side of the
assembly. Re-install Axle screw and tighten.
Install hinge stile push pad cover with 2 ea. 8-32
x 1 1/2” screws. Now you set you latch retraction
adjustment with our “PTS”technology.
See page #2
Optional STEP - How to change handing
B.
A.
C.
Lifting arm.

13
PD10 Parts Breakdown

14
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002