Commell CMB-37B User manual

1
CMB-37B
Mini Barebone system
Intel High Performance Platform
Installation Guide
Edition 1.0
2013/06/18

CMB‐37BInstallationGuide
2
Document Content:
zPacking List
zProduct Specification
zHardware Installation
Packing List:
CMB-37B Chassis x 1
(Including LS-37B Motherboard)
DSPD-080-12A 80W AC-DC Adapter x 1
CPU Cooler x 1
PS/2 Keyboard & Mouse Cable x 1
DVI Adapter x1, DVI Cable x1
CMB-37B

CMB‐37BInstallationGuide
3
COM PORT cable x 1
DC_IN Power Cable x 1
SATA (7P+15P)Cable x 1
CD Driver x1
CMB-37B

CMB‐37BInstallationGuide
4
Hardware Installation:
<Motherboard placement>
SATA1
SATA2
CN_AUDIO
CD_IN CN_INV
CN_COM2
CN_DIO CN_SMBUS
CN_IR JFRNT
SYSFAN
CPUFAN
DC_OUT
DC_IN
CN_USB1
CN_USB3-0
CN_LPC
CN_LVDS
CN_DVI
SIMM
MINI_CARD2
MINI_CARD1
JACT
JSPD
CN_LVDS
CN_IR
JP2
JP1
JCSEL1
JCSEL2 JAT
JRTC
For Connector For Jum
p
er

CMB‐37BInstallationGuide
5
SO-DIMM
COM CRT PS/2 USB LAN

CMB‐37BInstallationGuide
6
<Jumper Location & Reference>
Jumper Function
JRTC CMOS Operating/Clear Setting
JVLCD Panel Voltage Setting
JAT Power mode select
JP1 Com1 Voltage Setting (For Pin 9)
JP2 Com2 Voltage Setting (For Pin 9)
JCSEL1
JCSEL2 CN_COM2 RS-232 RS422 RS485 Setting
CN_IR IrDA Setting
Jumper: JAT
Type: onboard 3-pin header
Power Mode JAT
AT Mode 1-2
ATX Mode 2-3
Default setting: ATX Mode
Jumper: JP1/JP2 (COM1/2)
Type: onboard 6-pin header
Power Mode JP1/2
Pin 9 with 5V Power 1-2
Pin 9 with 12V Power 3-4
Standard COM port 5-6
Default setting
13
1 2
5 6

CMB‐37BInstallationGuide
7
Setting RS-232 & RS-422 & RS-485 for COM2
Jumper: JCSEL1,JCSEL2
Type: 12-pin (6 x 2) & 8-pin (4 x 2) for set COM2 mode jumper
RS232 RS485 RS422 IrDA
JCSEL1
JCSEL2
Default: RS232

CMB‐37BInstallationGuide
8
<Internal Connectors>
Connector Function Remark
CPU Socket rPGA988B for PGA988 CPU
SO-DIMM 204 -pin DDR3 SO-DIMM socket
SATA 1/2 7-pin Serial ATAIII connector
DC_IN DC 9~24V input connector
DC_OUT 4-pin DC output connector
CN_AUDIO 5 x 2-pin audio connector
CD_IN 4-pin CD-ROM audio input connector
CN_DIO 6 x 2-pin digital I/O connector
CN_USB 1/2 5 x 2-pin USB connector
CPUFAN 4-pin CPU cooler fan connector
SYSFAN 3-pin system cooler fan connector
CN_DVI 10 x 2-pin DVI connector
CN_LVDS 20 x 2-pin LVDS connector
CN_INV 5-pin LCD inverter connector
CN_IR 5-pin IrDA connector
CN_COM2 9-pin RS232/485/422
CN_LPC 5 x 2-pin LPC connector
JFRNT 10-pin front panel switch/indicator
connector
Mini-PCIE1/2 52-pin Mini-PCIE socket
JAT Power mode select
JSPD LAN Speed LED connector
JACT LAN Activity LED connector
<External Connectors>
Connector Function Remark
COM1 DB9 Serial port connector
CRT DB15 VGA connector
PS2 PS/2 keyboard and mouse connector
USB Dual USB 3.0 connector
RJ45 RJ45 LAN connector

-9-
<CPU and Memory Setup>
The board comes with the socket rPGA988 for Intel Ivy Bridge Processor, Please follow
the instruction to install the CPU properly.
1.Usetheflat‐type
screwdriveto
Unlock wa
y
Check
p
oint
2.Followthepin
3.Lockthesocket
Socket CPU
Check point

-10-
2.4.2 <Memory Setup>
The board provides 1 x 204-pin DDR3 SO-DIMM to support 800/1066MHz DDR3 memory
module up to 4GB.
SO-DIMM

-11-
I/O panel:
Front:
USB
Power Button
HD LED
Power LED
Line-Out
Mic Phone

-12-
Rear panel:
COM1
DVI
VGA

-13-
Chassis Setup procedure:
1. Screw off as indication of the picture below.

-14-
2. Push the Chassis shield towards the back then open it.

-15-
3. Turn the CPU cooler screws and then refer the page.9 to install the
CPU.(After installing CPU, please turn the CPU FAN screws to tighten.)
4. Screw off as indication of the picture below.

16
5. Insert the DDRII SO-DIMM module into the socket at 45 degree.
Press down the module with a click sound.

17
6. Put on HDD driver into HDD holder then turn the HDD drive screws
to tighten.

18
7. Connect SATA cable to motherboard.
8. Put SATA cable holder through the motherboard holder.

19
9. Connect SATA cable from motherboard to the HD drive.
10. Put the Chassis shield back and screw on as indication of the
picture below Turn the screws.

20
11. Put the top Chassis shield back and screw on as indication of the
picture below.