Commercial CHEF CHP63MS User manual

Page 1
User Manual
Electric Pressure Cooker
MODEL: CHP63MS
1. READ these instructions carefully before installing and operating the
appliance. Keep them for further reference.
2. Record in the space below the “SERIAL/MODEL NUMBER” found on the back
or bottom of your appliance and retain this information for future reference.
SERIAL NUMBER:
MODEL NUMBER:
DATE OF PURCHASE:
Save and staple your sales receipt to your manual for warranty coverage.

Page 2

Page 3
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS
1. READ ALL INSTRUCTIONS BEFORE USE
2. Do not touch hot surfaces. Only use side handles or knobs for
carrying or moving.
3. To protect against electrical shock, do not immerse the power cord,
plugs or appliance in water or other liquid.
4. Close supervision is necessary when the appliance is used by or
near children.
5. Unplug from outlet when not in use and before cleaning. Allow to
cool before putting on or taking off parts.
6. Do not operate any appliance with a damaged cord or plug, or after
the appliance malfunctions or has been damaged in any manner.
Return appliance to the nearest authorized service facility for
examination, repair, or adjustment.
7. The use of accessory attachments not recommended by the
appliance manufacturer may cause injuries.
8. For household use only.
9. Do not use outdoors.
10. Do not let power cord hang over edge of table or counter, or touch
hot surfaces.
11. Do not place the appliance on or near a hot gas or electric burner,
or a heated oven.
12. Extreme caution must be used when moving the appliance
containing hot liquids.
13. To disconnect, turn appliance “off”, then remove plug from wall
outlet.
14. Do not use appliance for anything other than intended use.
15. This appliance cooks under pressure. Improper use may result
in scalding injury. Make certain unit is properly closed before
operating. Please see the “Getting Started” section.
DANGER
DANGER - Immediate hazards
which WILL result in severe
personal injury or death
WARNING
WARNING - Hazards or unsafe
practices which COULD result in
severe personal injury or death
CAUTION
CAUTION - Hazards or unsafe
practices which COULD result in
minor personal injury
WARNING
When using electrical appliances, basic safety precautions
should be followed, including the following

Page 4
16. Donotlltheapplianceover2/3full.Whencookingfoodsthat
expandduringcookingsuchasriceordriedvegetables,donotll
theapplianceover1/2full.Overllingmaycauseariskofclogging
the vent pipe and developing excess pressure. See the “Food
Preparation/Pressure Cooking” section.
17. Do not open the appliance until the appliance has cooled and all
internalpressurehasbeenreleased.Iftheoatvalveisstillupand/
orthelidisdifculttoopen,thisindicatesthattheapplianceisstill
pressurized – do not force it open. Any pressure in the appliance
can be hazardous. Please see the “Getting Started” section for
instructions to safely remove lid.
18. Always check the pressure release devices for clogging before use.
19. Do not use this appliance for pressure frying with oil.
20. To prevent risk of explosion and injury, replace only dynamic
seal ring as recommended by the manufacturer. See Operating
Instructions.
21. Intended for countertop use only.
22. WARNING: Spilled food can cause serious burns. Keep appliance
and cord away from children. Never drape cord over edge of
counter, never use outlet below counter, and never use with an
extension cord.
23. CAUTION: Risk of Electric Shock. Cook only in removable container.
24. This appliance is not intended for deep frying foods.
SAVE THESE INSTRUCTIONS
HOUSEHOLD USE ONLY
SAFETY INFORMATION

Page 5
SAFETY INFORMATION
ELECTRICAL REQUIREMENTS
This appliance has a polarized plug (one blade is wider than the other). To reduce the
riskofelectricshock,thisplugisintendedtotintoapolarizedoutletonlyoneway.
Iftheplugdoesnottintotheoutlet,reversetheplug.Ifitstilldoesnott,contacta
qualiedelectrician.Donotattempttomodifythepluginanyway.
POWER SUPPLY CORD
1. A short power supply cord is provided to reduce the risk of becoming entangled in
or tripping over a longer cord.
2. If the power supply cord is too short, do not use an extension cord. Have a
qualiedelectricianorservicemaninstallanoutletneartheappliance.
3. If it is absolutely necessary to use longer cord sets or an extension cord, extreme
care must be exercised.
a) The marked electrical rating of the cord set or extension cord must equal to or
be greater than the electrical rating of the appliance. The longer cord should be
arranged so that it will not drape over the counter top or table top where it can be
pulled on by children or tripped over unintentionally.
NOTE: Neither Commercial Chef nor the dealer can accept any liability for damage to
the product or personal injury resulting from failure to observe the electrical
connection procedures.

Page 6
PARTS & FEATURES
SET UP & USE
11 12
14
18
19
20
21
22
15
16
13
17
1
2
3
4
5
6
7
8
9
10
No. Description
1Exhaust valve handle
2Upper cover handle
3Lid position marker
4Seal ring
5Internal side of lid
6Fill lines
7Condensation collector rim
8Housing cover
9Control panel and display
10 Base
11 Exhaust opening
12 Float valve
13 Exhaust valve
14 Seal ring bracket
15 Sealing gate
16 Siliconecapbeneathoatvalve
17 Block proof cover
18 Inner pot
19 Outer pot
20 Base handles
21 Cooker body
22 Power cord
Model Capacity Power
Supply
Rated
Power
Size of
Inner Pot
Working
Pressure
Keep Warm
Temperature
CHP63MS 6 Qt 120V~
60Hz 1000W 8.66” 70kPa 140° F~176° F
Accessories
Spoon Soup Spoon User Manual Water box Measuring cup Steam rack

Page 7
SET UP & USE
PRODUCT STRUCTURE
Structural diagram of oat valve
Tips:
1. Confirm that the float valve, block proof cover and seal ring are correctly installed
before use each time;
2. Before putting the inner pot into the cooker each time, please remove the dirt and
water from the external side of the inner pot and internal side of the external pot;
3. Please move the product using the base handles of the cooker body;
4. Please remove water from the housing cover with cloth.
Note:
1. Exhaust valve: Pull out the exhaust valve from the lid. Clean the exhaust valve and
float valve of the lid with brush and cloth at least once a month.
2. Sealing gate: Please remove oil and dirt from the sealing gate with detergent and
brush. The remaining oil and dirt in it may appear yellowish. After washing, it may
recover to the original color as stainless steel. It is suggested to clean the sealing
gate once every 2 months.
3. Condensation collector: After cooking, the steam may build up in the condensation
collector as water. Water in the collector should be removed using a clean cloth to
avoid odors.

Page 8
INSTRUCTIONS FOR USE
BEFORE FIRST USE
Whenusingforthersttime,pleasetakeoutallaccessoriesfromthecookerbody,
read the User Manual carefully, particularly for usage and cautions to avoid property
loss or personal physical injury.
CONTROL PANEL
TEXTURE/Pressure function
To change the consistency of the food (LOW, MID, HIGH), simply press “TEXTURE”.
The appropriate light will display, indicating that the time has been changed. The
time in the display will automatically adjust accordingly. (Ex: For the “rice” function,
“LOW” is 7 minutes, “MID” is 10 minutes and “HIGH” is 21 minutes.)
Cooking Timer Function
WhenusingTimerfunction,rstpress“Timer”andthenadjustthetimermanuallyby
pressing “+” or “-” buttons to adjust duration of cooking time.
Delay Timer Function
Setthetimeofnishingcookingbypressingthe“+”/“-”button.
SET UP & USE
Display Screen
“-” Button
Timer Button
“+” Button
START/ON/OFF Button
CANCEL Button
TEXTURE Button

Page 9
Disassemble and install the block proof cover and seal ring
Disassemble and install the block proof
cover
1. Check if the seal ring and block proof
cover are correctly installed in the
upper cover before use each time.
2. After use, please clean the seal ring
and around block proof cover to avoid
jamming the cover, keep it clean to
avoid bad odor.
Disassemble and install the seal ring 1. Please do not pull the seal ring,
otherwise, the distorted seal may
inuencethesealingandpressure
effect.
2. Do not use the damaged sealing,
please replace it at the authorized
repairofce.
SET UP & USE
USE AND MAINTAIN THE INNER POT
1. Do not remove for extended period
Inner pot may become yellowed, spotted or stained. Bottom may become
distorted when removed from cooker for extended periods of time.
2. Do not use it to store acid, alkali and preserved foods for a long period
Although the inner pot has excellent anti-corrosion performance, the inner pot
may be corroded to a certain degree when warm foods and substances are stored
longer than 24 hours.
3. Keep it clean to prolong the service life
Do not immerse it in water for a long period.
Clean the inner pot with soap, weak detergent or warm water to remove dust, oil
and dirt.
4. Do not scratch it with steel wire brushes and scrubs
Soften the burnt foods on the bottom with water and then remove it.
Tips:
The bright inner pot has smooth and polished surface before use. After long periods
of use, the surface can lose its shine and luster after repeated cleanings with hard
scrubs.Itisnormalandwon’tinuencethefunctionoftheproduct.
Disassemble
Pull it out upwards
Disassemble
Pull it out upwards
Block
proof
cover
Seal ring
Install
Press it down
to install
Install
Press it down
to install

Page 10
SET UP & USE
PREPARE FOR COOKING
1. Opening the lid correctly
• Hold the handle of upper cover, turn it
counterclockwise for about 30° till the “ ”
mark on the edge of the upper cover lines
up with the“ ” mark on the edge of the
housing cover, and then lift the upper cover.
2. Check if the parts and accessories of lid are
correctly installed
•Checkiftheoatervalveandexhaust
valvearejammed,conrmifthesealing
ring and block proof cover are installed
appropriately.
3. Take out the inner pot, put the foods and
water into the inner pot
• The total amount of foods and water shall
not exceed the Max marked on the inner
pot.
• The max rice and water amount when
cooking shall not exceed the Max on the
inner pot.
4. Put the inner pot into the cooker
• Wipe to clean the external surface of inner
pot, foreign object and water are not
allowed on the inner surface of electric
pressure cooker;
• Turn the inner pot to left and right to ensure
good contact with the heating plate.
5. Safely close the lid
• Before closing the lid, check if the sealing
ring is installed correctly.
• Hold the handle of upper cover, line the
“ ” mark on the edge of the upper cover
with the “ ” mark on the edge of the
housing cover, press down and turn the
upper cover clockwise for about 30° to lock
in place, and aim the “ ” mark on the edge
of the housing cover with the “ ” mark on
the lid.
6. Switch the exhaust valve
• When cooking, please turn the exhaust
valve to the sealing position, which means
the electric pressure cooker keeps at sealing state;
• For manual exhaust, please turn the exhaust valve handle to the exhaust position,
the electric pressure cooker keeps at the exhaust state; when exhausting, do not
keep hands or face above the exhaust opening;
•Checkiftheoatervalvedropsdownbeforeworking(beforeheating,theoater
valve is down).

Page 11
SET UP & USE
GENERAL FUNCTION
1. Prepare for cooking according to the method listed on Page 8 and 9.
2.Conrmiflidisclosedcorrectlyasbuttonswillremaininactiveiflidisoutofplace
or open. Press START/ON/OFF button if display is active and ready for use.
3. Under standby state, the corresponding indicator will be displayed when the
following buttons are pressed: The “TEXTURE” light is on. Press “TEXTURE” you
can choose “LOW”, “MID” OR “HIGH”. Then press “START/ON/OFF”, to begin
cooking. When the pressure goes up and become set-up pressure, it becomes
stable. Display will show the timetable and count down.
4. After cooking, the cooker may automatically enter into the keep warm state. The
time of keep warm shall not exceed 24h.
5. When cooking is complete, the corresponding function turns off and enters the
keep warm feature. When keep warm is activated, the cooker will beep and the
keep warm light will remain active. When on standby, press the “Warm” button to
keepthewarmindicatorlightson.Themachinewillbeeptoconrmkeepwarm
feature is active.
Tips:
During any cooking operation, press the “CANCEL” button to cancel the current
work state and return to standby state.
Occasional clicking sounds during cooking is normal.
To cook a small amount of food, the inner pot may possibly be lifted when opening
the lid, please shake the lid to drop the inner pot in the cooker body and then remove
the lid.
SAFELY OPEN THE LID
1. Cut off power supply or remove the power plug
2. Exhaust method
A. Exhaust Valve Release
Turntheexhaustvalvetotheexhaustpositiontoreleasesteamuntiltheoat
valvedropsdown.(Fornon-uidfoods)
B. Natural cooling method
Lettheelectricpressurecookercoolnaturallytilltheoatvalvedropsdown.
3. Open the lid
Turn the upper cover counterclockwise until the lid is unlocked and lift to open the
lid.
Do not open the lid before the pressure in the pot has been completely released.
DONOTattempttoopenthelidbyforceifitisdifculttoopen.
Do not pull out the exhaust valve when turning the exhaust valve.
Aftercookinguidfoods(porridgeandsoup),donotturntheexhaustvalve,
pleasecutoffpowersupplytomakeitcoolnaturallytilltheoatdropsbefore
opening the lid.
After cooking a large amount of food, please do not immediately exhaust, it is
suggested to keep warm before opening the lid.

Page 12
SET UP & USE
Function Operation Guidelines
Power On
When the power is on, the digital screen displays nothing, the
LED is not on, the buzzer does not sound and the appliance
does not heat up.
Standby
When “ ” is pressed, the digital screen will display 88:88,
the LED will be on for one second, and the buzzer will sound
once.
Then the appliance will enter the standby state, the digital
screen will display “— — — —”, and the LED will light off.
Rice
1. Normal cooking: In the standby state, when the “Rice”
buttonispressed,the“Rice”indicatorwillashandthe
“MID” light will be on, while the digital screen will display
“Auto”, showing that the pressure maintaining time will
be automatically adjusted. Press the “TEXTURE” button
to adjust the preset texture settings: “LOW/MID/HIGH”.
Press to start cooking, then the buzzer will sound
and the digital screen will display . When the pressure
rises, will light on, and the digital screen will display the
pressure maintaining time and start to count down. When
thecountdowniscomplete,thecookingisnishedandthe
buzzer will sound, while the system automatically keeps
warm. The “Warm” indicator is on and the digital screen will
display the warm-keeping time. At this time, you can open
the lid and enjoy the food.
2. Delay cooking: Press the “Rice” button and the “Timer”
button during standby mode to enter delay cooking mode,
the “Rice”, “MID” and “Timer” indicators will light on and
the digital screen will display the preservation time “2:00”
by default. Press the “Timer” button again and the “+” /
“-” buttons to adjust the time. Press to start delay
cooking, then the buzzer will sound and will light on,
and the digital screen will start to count down. When the
countdowniscomplete,thecookingisnishedandthe
buzzer sounds, while the system automatically keeps warm.
The “Warm” indicator is on and the digital screen displays
the warm-keeping time. At this time, you can open the lid
and enjoy the food.
3. Exit the working state: Press the “CANCEL” button to
exit the current cooking operation or cancel the current
parameter setting.
4. Turn off: Press “ ” in the standby state to shut down the
appliance.
OPERATION GUIDELINES

Page 13
SET UP & USE
Function Operation Guidelines
Brown Rice
1. Normal cooking: In the standby state, when the “Brown
Rice” button is pressed, the “Brown Rice” indicator will
ickerandthe“MID”lightwillbeon,thedigitalscreenwill
display “Auto”, showing that the pressure maintaining time
will be automatically adjusted. Press the “TEXTURE” button
to adjust the preset texture settings “LOW/MID/HIGH”.
Press to start cooking, then the buzzer will sound
and the digital screen will display . When the pressure
rises, will light on, and the digital screen will display the
pressure maintaining time and start to count down. When
thecountdowniscomplete,thecookingisnishedandthe
buzzer sounds, while the system automatically keeps warm.
The “Warm” indicator is on and the digital screen displays
the warm-keeping time. At this time, you can open the lid
and enjoy the food.
2. Delay cooking: Press the “Brown Rice” button and the
“Timer” button during standby mode to enter the delay
cooking mode, the “Rice”, “MID” indicators will light on,
the“Timer”indicatorwillicker,andthedigitalscreenwill
display the preservation time “2:00” by default. Press the
“Timer” button again and the “+”/”-” buttons to adjust the
time. Press to start delay cooking, then the buzzer
will sound and will light on, and the digital screen will
start to count down. When the countdown is complete, the
cookingisnishedandthebuzzersounds,whilethesystem
automatically keeps warm. The “Warm” indicator is on and
the digital screen displays the warm-keeping time. At this
time, you can open the lid and enjoy the food.
3. Exit the working state: Press the “CANCEL” button to
exit the current cooking operation or cancel the current
parameter setting.
4. Turn off: Press “ ” in the standby state to shut down the
appliance.

Page 14
SET UP & USE
Function Operation Guidelines
Steam/
Soup/
Stew/
Meat Ribs/
Poultry/
Fish/
Bean Chilli/
Vegetable
“Steam” button for example:
1. Normal cooking: In the standby state, when the “Steam”
buttonispressed,the“Steam”indicatorwillickerandthe
“MID” light will be on, while the digital screen will display
“0:20”, showing that the pressure maintaining time is 20
minutes. Press the “TEXTURE” button to adjust the preset
texture settings; “LOW/MID/HIGH”. Press to start
cooking, then the buzzer will sound and the digital screen
will display . When the pressure rises, will light on,
and the digital screen will display the pressure maintaining
time and start to count down. When the countdown is
complete,thecookingisnishedandthebuzzersounds,
while the system automatically keeps warm. The “Warm”
indicator is on and the digital screen displays the warm-
keeping time. At this time, you can open the lid and enjoy
the food.
2. Delay cooking: Press the “Steam” button and the “Timer”
button during standby mode to enter delay cooking mode,
the “Steam”, “MID” and “Timer” indicators will light on
and the digital screen will display the preservation time
“2:00” by default. Press the “Timer” button again and the
“+”/”-” buttons to adjust the time. Press to start delay
cooking, then the buzzer will sound and will light on,
and the digital screen will start to count down. When the
countdowniscomplete,thecookingisnishedandthe
buzzer sounds, while the system automatically keeps warm.
The “Warm” indicator is on and the digital screen displays
the warm-keeping time. At this time, you can open the lid
and enjoy the food.
3. Exit the working state: Press the “CANCEL” button to exit
the current or cancel the current parameter setting.
4. Turn off: Press “ ” in the standby state to shut down the
appliance.

Page 15
SET UP & USE
Function Operation Guidelines
Sauté/Sear
1. Normal cooking: In the standby state, when the “Sauté/
Sear” button is pressed, the “Sauté/Sear” indicator will
ickerandthe“MID”lightwillbeon,whilethedigitalscreen
will display “0:20”, showing that the cooking time is 20
minutes. Press the “TEXTURE” button to adjust the preset
texture settings: namely “LOW/MID/HIGH”. Press
to start cooking, then the buzzer will sound, will light
on, and the digital screen will display the countdown of
20 minutes, showing that the appliance starts to heat up.
Whenthecountdowniscomplete,thecookingisnished
and the buzzer sounds; at this time, you can open the lid
and enjoy the food.
2. Delay cooking: This function is not available for this menu.
3. Exit the working state: Press the “CANCEL” button to
exit the current cooking operation or cancel the current
parameter setting.
4. Turn off: Press “ ” in the standby state to shut down the
appliance.
Cake 1. Normal cooking: In the standby state, when the “Cake”
buttonispressed,the“Cake”indicatorwillickerandthe
“MID” light will be on, while the digital screen will display
“0:36”, showing that the cooking time is 36 minutes. Press
the “TEXTURE” button to adjust the preset texture settings:
“LOW/MID/HIGH”. Press to start cooking, then the
buzzer will sound, will be on, and the digital screen
will display the countdown of 20 minutes, showing that
the appliance starts to heat up. When the countdown is
complete,thecookingisnishedandthebuzzersounds,
while the system automatically keeps warm. The “Warm”
indicator is on and the digital screen displays the warm-
keeping time. At this time, you can open the lid and enjoy
the food.
2. Delay cooking: This function is not available for this menu.
3. Exit the working state: Press the “CANCEL” button to
exit the current cooking operation or cancel the current
parameter setting.

Page 16
Function Operation Guidelines
Cake
4. Turn off: Press “ ” in the standby state to shut down the
appliance.
Note: Please note that when using this function, do not put
food directly into the inner pot. Before making a cake,
place the steam rack in the bottom and pour some
waterintotheinnerpotrst,thenputyourmaterialsin
aplate,andcarefullycenterthelledplateonthesteam
rack.
Slow Cook
1. Normal cooking: In the standby state, when the “Slow
Cook” button is pressed, the “Slow Cook” indicator will
ickerandthe“MID”lightwillbeon,whilethedigitalscreen
will display “0:36” showing that the cooking time is 36
minutes. Press the “TEXTURE” button to adjust the preset
texture setting: “LOW/MID/HIGH”. Press to start
cooking, then the buzzer will sound, will be on, and the
digital screen will display the countdown of 20 minutes,
showing that the appliance starts to heat up. When the
countdowniscomplete,thecookingisnishedandthe
buzzer sounds, while the system automatically keeps warm.
The “Warm” indicator is on and the digital screen displays
the warm-keeping time. At this time, you can open the lid
andenjoy the food.
2. Delay cooking: This function is not available for this menu.
3. Exit the working state: Press the “CANCEL” button to
exit the current cooking operation or cancel the current
parameter setting.
4. Turn off: Press “ ” in the standby state to shut down the
appliance.
SET UP & USE

Page 17
Function Operation Guidelines
Manual
1. Normal cooking: After pressing the “Manual” button in the
standbystate,the“Manual”indicatorwillickerandthe
digital screen will display “0:30”, showing that the pressure
maintaining time is 30 minutes by default. Press the “+”/”-”
buttons to adjust the pressure cooking. Press to start
cooking, then the buzzer will sound and the digital screen
will display . When the pressure rises, will light on,
and the digital screen will display the pressure maintaining
time and start to count down. When the countdown is
complete,thecookingisnishedandthebuzzersounds,
while the system automatically keeps warm. The “Warm”
indicator is on and the digital screen displays the warm-
keeping time. At this time, you can open the lid and enjoy
the food.
2. Delay cooking: Press the “Manual” button and the “Timer”
button during standby mode to enter the delay cooking
mode, the “Manual”, “MID” and “Timer” indicators will light
on and the digital screen will display the preservation time
“2:00” by default. Press the “Timer” button again and the
“+”/”-” buttons to adjust the time. Press to start delay
cooking, then the buzzer will sound and will light on,
and the digital screen will start to count down. When the
countdowniscomplete,thecookingisnishedandthe
buzzer sounds, while the system automatically keeps warm.
The “Warm” indicator is on and the digital screen displays
the warm-keeping time. At this time, you can open the lid
and enjoy the food.
3. Exit the working state: Press the “CANCEL” button to
exit the current cooking operation or cancel the current
parameter setting.
4. Turn off: Press “ ” in the standby state to shut down the
appliance.
SET UP & USE

Page 18
Function Operation Guidelines
Warm
1. Normal warm-keeping: When the “Warm” button is pressed
during standby state, the “Warm” indicator will be on, and
the digital screen will display “0:00”. Press to start
keeping warm. At this time, the buzzer sounds, the “Warm”
indicator lights on, and the digital screen displays the warm
preservation time.
2. Delay cooking: This function is not available for this menu.
3. Exit the working state: Press the “CANCEL” button to exit
the current working state.
4. Turn off: Press “ ” in the standby state to shut down the
appliance.
If following occurs Solutions
• Power cord and plug is expanded, deformed,
damaged or color is changed.
• A part of the power cord and plug is
overheating.
•Powercordisexiblewithdiscontinuous
power supply.
• The electric pressure cooker has abnormal
heating and generates bad odor.
• There’s abnormal noise or vibration when
plugged in.
Stop using, and have machine by
the authorized repair center.
• There’s dust or dirt on the plug or socket. Remove the dust or dirt.
SET UP & USE
KEEP WARM FUNCTION
1. After cooking, the electric pressure cooker automatically enters
into the keep warm state; when the keep warm feature is active,
the keep warm indicator will remain lit.
2. During standby state, you may also press the “ Warm” button to
keep warm;
3. Keep warm temperature is 140°F~176°F;
DAILY CHECK AND MAINTENANCE
To use the product safely with a longer service life, please carefully check and
maintain it.

Page 19
Use 120V~ 60Hz power outlet
• Failure to use AC 120V~ 60Hz electricity
cancausereorelectricshock.
•Dangerofreifpluggedintoinappropriate
outlet.
A socket shall be used alone
• A socket of more than 10A rated current
with grounding wire shall be used alone;
• If shared with other electrical appliances,
the socket may cause abnormal heat and
resultinre.
It is strictly prohibited to use other lid
• It is strictly prohibited to use other lid for
heating, and in the (switching on) process,
the use of non-original lid is not allowed.
• As this may cause electric shock or safety
hazards.
SET UP & USE
SAFETY PRECAUTIONS
To avoid personal injury and property loss, be sure to observe the following safety
precautions.
• Warning & Caution Label Icons:
•ThefollowingdangersmayoccurwhendisobeyingWarning&Cautionnotications:
WARNING: May cause probable death or serious injury if warning items are
disobeyed.
CAUTION: May cause physical injury or property damage if caution items are
disobeyed.
WARNING
Do not use
Do not use
Do not touch Do not get
wet
Do not touch
with wet
hands
Do not
disassemble
Must be
completed
Unplug the
power cord
Mandatory
items

Page 20
SET UP & USE
Stop using if the power cord is damaged
• Replace the damaged power cord with
special soft cord or replace it with special
assembly purchased from the manufacturer or
authorized repair center.
Do not put foreign objects
• It is prohibited to insert metal shavings,
needles and other foreign matter in gaps and
openings.
• As this may cause electric shock or movement
anomalies.
Place the appliance in a location out of reach
of infants
• Place the appliance in a location out of reach
of infants.
• To avoid electric shock and burns.
Modication is prohibited
•Modicationorrepairbynon-professionalsis
prohibited.
•Violationmaycauseareorelectricshock.
• Repair or replacement of parts must be made
in a designated service center.
Products may not be immersed or sprinkled in
water
• Doing so could cause electric shock and
electrical short circuits.
Warning on Opening the lid
• When the electric pressure cooker is not working, there isn’t pressure in the pot,
theoatvalveisdown;
• When the electric pressure cooker is working, pressure in the cooker rises,
oatvalveascends;donotforcefullyopenthelidbeforethepressurehasbeen
completely released;
•Ifitisdifculttoopenthelid,pleasedonotopenitforcefully,otherwise,itmay
cause burns or physical injury.
WARNING
Table of contents
Languages: