CommScope RUCKUS SmartZone 300 User manual

RUCKUS SmartZone 300
AC Power Supply Unit
Quick Setup Guide
This Quick Setup Guide provides informaon on how to order a
replacement AC power supply unit (PSU) for the SmartZone 300
(SZ300) controller. It also describes how to replace the AC PSU on
the controller.
For addional guides that describe how to install or replace other
eld-replaceable units (FRUs) on the SmartZone 300 controller,
visit the Ruckus Support website at:
hps://support.ruckuswireless.com/documents
This Guide in Other Languages
请从以下网站获得该指南的简体中文版 hps://
support.ruckuswireless.com.
Vous trouverez la version française de ce guide à l'adresse
suivante hps://support.ruckuswireless.com.
このガイドの日本語版は hps://support.ruckuswireless.com
でご覧ください。
이 가이드의 한국어 버전은 웹 사이트 (hps://
support.ruckuswireless.com) 에서 확인하시기 바랍니다.
Veja a versão em português (Brasil) deste guia em hps://
support.ruckuswireless.com.
Puede ver la versión en español (América Lana) de esta guía en
hps://support.ruckuswireless.com.
AC Power Supply Unit Ordering Informaon
To order a replacement AC power supply unit for the SmartZone
300 controller, contact Ruckus Support.
For informaon on how to contact Ruckus Support, visit hps://
support.ruckuswireless.com/contact-us. When asked for the part
number, provide the informaon in the following table.
TABLE 1 AC Power Unit Part Number
Part Number Descripon
902-S310-AC00 Kit, spare, AC power supply, SZ300 (use with
902-0174-XX00 power cord)
Replacing the AC Power Supply Unit on the
SmartZone 300
When a power supply unit (PSU) on the SmartZone 300 fails,
obtain a new PSU from Ruckus and replace the faulty PSU. You
can tell if a PSU has failed if its status LED is red and it is eming
long, recurring beeps.
NOTE: The PSU is hot pluggable; you do not need to power
down the controller before replacing it.
DANGER: The PSU may be hot! Exercise cauon when touching
the PSU.
1. Locate the PSU that must be replaced.
FIGURE 1 AC PSU
2. Disconnect the power cable from the failed PSU.
3. Unlock the PSU by sliding the lock to the le.
FIGURE 2 Unlocking the PSU
4. Hold the lock, and pull the handle of the PSU away from the
chassis to remove it.
FIGURE 3 Removing the PSU
5. Remove the replacement PSU from its anstac packaging,
and verify that there is no visible damage to it.
Copyright © 2021 CommScope, Inc. All rights reserved. Page 1 of 2
Published December 2021, Part Number 800-72221-001 Rev D

NOTE: If you noce any visible damage, contact Ruckus
Support.
6. Remove the protecve cover over the AC power supply
connector on the rear of the unit.
7. Insert the replacement PSU (in the same orientaon as the
PSU that you removed) into the bay. When the module is fully
seated in the bay, the PSU lock automacally slides to the
right to lock the PSU in place.
8. Reconnect the power connector unl it is fully seated.
The PSU powers on and the PSU status LED shows a green OK
light.
You have completed replacing the AC PSU of the SmartZone 300.
© 2021 CommScope, Inc. All rights reserved.
ARRIS, the ARRIS logo, COMMSCOPE, RUCKUS, RUCKUS WIRELESS, the Ruckus
logo, and the Big Dog design are trademarks of CommScope, Inc. and/or its
aliates. Wi-Fi Alliance, Wi-Fi, the Wi-Fi logo, Wi-Fi Cered, the Wi-Fi
CERTIFIED logo, Wi-Fi Protected Access, the Wi-Fi Protected Setup logo, Wi-Fi
Protected Setup, Wi-Fi Mulmedia and WPA2 and WMM are trademarks or
registered trademarks of Wi-Fi Alliance. All other trademarks are the property of
their respecve owners.
Copyright © 2021 CommScope, Inc. All rights reserved. Page 2 of 2
Published December 2021, Part Number 800-72221-001 Rev D