Comnet CNGE24MS User manual

INSTALLATION AND OPERATION MANUAL
CNGE24MS
ENVIRONMENTALLY HARDENED MANAGED ETHERNET SWITCH
WITH (8) 100/1000BASE-FX & (16) GIGABIT COMBO PORTS
v1.4 February 25, 2013
The ComNet™CNGE24MS has eight 100/1000Base-FX SFP ports and sixteen Gigabit
combo ports that allow for TX or FX transmission. All SFP ports utilize ComNet Small
Form Factor (SFP) pluggable modules for the selection of fiber and connector type and
distance. The IEEE802.3-compliant unit offers multiple Ethernet redundancy protocols
(ComRing, C-Ring, and MSTP/RSTP/STP) which protect your applications from network
interruptions or temporary malfunctions by redirecting transmission within the
network. The switch provides advanced IP-based management that can limit the
maximum bandwidth for each connected IP device, allowing the user to adjust
usage. Application-based QoS can set a higher priority for data streaming. The Device-
Binding function can prevent unauthorized network access, increasing security. The
unit also provides advanced DOS/DDOS auto prevention. If IP flow becomes too large,
too quickly, the switch will lock the source IP address for a set period preventing
unauthorized access. The switch offers centralized and convenient management and
is also configurable by Web-based Telnet, and Console (CLI) configurations.

INS_CNGE24MS_REV–
02/18/13 PAGE 2
INSTALLATION AND OPERATION MANUAL CNGE24MS
Tech SupporT: 1.888.678.9427
Contents
Regulatory Compliance Statement 3
Warranty 3
Disclaimer 3
Safety Indications 3
Overview 4
Introduction 4
Software Features 5
Hardware Features 6
Hardware Overview 7
Front Panel 7
Rear Panel 8
Rack mount kit assembly 9
Front Panel LEDs 10
Cables 11
Ethernet Cables 11
10/100/1000BASE-T(X) Pin Assignments 11
SFP 13
Console Cable 14
WEB Management 16
Configuration by Web Browser 16
About Web-based Management 16
Command Line Interface Management 92
About CLI Management 92
Technical Specifications 105

INS_CNGE24MS_REV–
02/18/13 PAGE 3
INSTALLATION AND OPERATION MANUAL CNGE24MS
Tech SupporT: 1.888.678.9427
Regulatory Compliance Statement
Product(s) associated with this publication complies/comply with all applicable regulations. Please
refer to the Technical Specifications section for more details.
Warranty
ComNet warrants that all ComNet products are free from defects in material and workmanship
for a specified warranty period from the invoice date for the life of the installation. ComNet will
repair or replace products found by ComNet to be defective within this warranty period, with
shipment expenses apportioned by ComNet and the distributor. This warranty does not cover
product modifications or repairs done by persons other than ComNet-approved personnel, and
this warranty does not apply to ComNet products that are misused, abused, improperly installed,
or damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
Disclaimer
Information in this publication is intended to be accurate. ComNet shall not be responsible for its
use or infringements on third-parties as a result of its use. There may occasionally be unintentional
errors on this publication. ComNet reserves the right to revise the contents of this publication
without notice.
Safety Indications
»The equipment can only be accessed by trained ComNet service personnel.
»This equipment should be installed in secured location.

INS_CNGE24MS_REV–
02/18/13 PAGE 4
INSTALLATION AND OPERATION MANUAL CNGE24MS
Tech SupporT: 1.888.678.9427
Overview
Introduction
The CNGE24MS series are managed redundant ring Ethernet switches with 16xGigabit combo
ports and 8x100/1000Base-X SFP ports. With complete support of Ethernet Redundancy protocol,
C-Ring (recovery time <20ms over 250 units of connection) and MSTP/RSTP/STP (IEEE IEEE
802.1s/w/D) can protect your mission-critical applications from network interruptions or temporary
malfunctions with its fast recovery technology. ComNet switches provide advanced and IP-based
bandwidth management that can limit the maximum bandwidth for each IP device. The user can
configure IP camera and NVR with more bandwidth and limit other device bandwidth. ComNet’s
switch series also support application-based QoS. Application-based QoS can set highest priority
for data stream according to TCP/UDP port number. And all functions of CNGE24MS can also be
managed centralized and convenient by e-Console, as well as the Web-based interface, Telnet
and console (CLI) configuration. Therefore, the switch is one of the most reliable choice for highly-
managed and Gigabit Fiber Ethernet applications.

INS_CNGE24MS_REV–
02/18/13 PAGE 5
INSTALLATION AND OPERATION MANUAL CNGE24MS
Tech SupporT: 1.888.678.9427
Software Features
»Fastest Redundant Ethernet Ring (Recovery time <20ms over 250 units connection)
»Supports Ring Coupling, Dual Homing, and RSTP-over-Ring
»Supports SNMPv1/v2/v3 & RMON & Port base/IEEE 802.1Q VLAN Network Management
»Event notification by Email, SNMP trap and Relay Output
»Web-based, Telnet, and Console (CLI) configuration
»Enable/disable ports, MAC based port security
»Port-based network access control (IEEE 802.1x)
»VLAN (IEEE 802.1q) to segregate and secure network traffic
»RADIUS centralized password management
»SNMPv3 encrypted authentication and access security
»RSTP (IEEE 802.1w)
»Quality of Service (IEEE 802.1p) for real-time traffic
»VLAN (IEEE 802.1q) with support for double-tagging and GVRP
»IGMP Snooping for multicast filtering
»Port configuration, status, statistics, mirroring, and security
»Remote Monitoring (RMON)

INS_CNGE24MS_REV–
02/18/13 PAGE 6
INSTALLATION AND OPERATION MANUAL CNGE24MS
Tech SupporT: 1.888.678.9427
Hardware Features
»3 ×Redundant power inputs
»Operating Temperature: -40 to 75°C
»Storage Temperature: -40 to 85°C
»Operating Humidity: 5% to 95%, non-condensing
»Casing: IP-30 Aluminum
»16 ×Combo ports with 10/100/1000Base-T(X) and 100/1000Base-X SFP
»8 ×100/1000Base-X SFP ports
»Console Port
»Dimensions (W ×D ×H): 431 ×342 ×44 mm

INS_CNGE24MS_REV–
02/18/13 PAGE 7
INSTALLATION AND OPERATION MANUAL CNGE24MS
Tech SupporT: 1.888.678.9427
Hardware Overview
Front Panel
The following table describes the labels that are affixed to the CNGE24MS.
Port Description
SFP ports 16 ×100/1000BaseX on SFP port(combo) &
8 ×100/1000BaseX on SFP port
Giga Ethernet Port 16 ×10/100/1000Base-T (combo)
Console Use RS-232 with DB9 connecter to manage switch.
I
0
1 5 6 72 3
84
I
0
8
CNGE24MS Front Panel
1. Console port (DB9)
2. 10/100/1000Base-T(X) Ethernet port and 100/1000Base-X SFP (combo port)
3. 100/1000Base-X Fiber port on SFP
4. Reset button: Push the button 3 seconds for reset; 5 seconds for factory default.
5. LED for Ethernet ports 1000Mbps Link/Act status
6. LED for Ethernet ports 10/100Mbps Link/Act status
7. LED for SFP ports Link/Act status
8. Front Panel LED Status:
»LED for PW1: When the PWR1 links, the green LED will be light on.
»LED for PW2: When the PWR2 links, the green LED will be light on.
»LED for PW3: When the PWR3 links, the green LED will be light on.

INS_CNGE24MS_REV–
02/18/13 PAGE 8
INSTALLATION AND OPERATION MANUAL CNGE24MS
Tech SupporT: 1.888.678.9427
»LED for STA: Green: Indicates that the system ready. The LED is blinking when the system is
upgrading firmware
»LED for PWR: This LED lights on when the power module is activated.
»LED for R.M. (Ring master): When the LED lights on, this switch is designated as the ring
master of the Ring topology.
»LED for Ring: When the LED light on, the C-Ring is activated.
»LED for DEF: System resets to default configuration.
»LED for Ping: System is processing “PING” request.
»LED for RUN: System is operating continuously.
»LED for RMT: System is accessed remotely.
»LED for Fault: Indicates unexpected event occurred.
Rear Panel
The rear panel of CNGE24MS is displayed as below:
I
0
1 2 3
CNGE24MS Rear Panel
1. Power Switch
2. Power input for AC 100V~240V / 50~60Hz.
3. Power input for DC 36~72V and fault relay output

INS_CNGE24MS_REV–
02/18/13 PAGE 9
INSTALLATION AND OPERATION MANUAL CNGE24MS
Tech SupporT: 1.888.678.9427
Rack mount kit assembly
You can find the rack-mount kit and the screws in the packing box. Please assemble the rack-
mount kit on the switch with screws as shown below:

INS_CNGE24MS_REV–
02/18/13 PAGE 10
INSTALLATION AND OPERATION MANUAL CNGE24MS
Tech SupporT: 1.888.678.9427
Front Panel LEDs
LED indicators
LED Color Status Description
PW1 Green On PWR1 linked
PW2 Green On PWR2 linked
PW3 Green On PWR3 linked
STA Green On The power module is in PWR UP state
Blinking The system is upgrading firmware
DEF Green On System resets to default configuration
RUN Green Slowly blinking System is operating continuously
PWR Green On DC power module activated
Ping Green Blinking System is processing “PING” request
RMT Green Blinking System is accessed remotely
Ring Green On Ring enabled
Slowly blinking Ring has only One link (lacks one link to build the ring)
Fast blinking Ring working normally
R.M Green On The system is operating in C-Ring Master mode
Fault Amber On Unexpected event occurred.
10/100/1000Base-T(X) Gigabit Ethernet ports
LINK/
ACT
Green On Port speed 1000Mbps link up
Blinking Data Transmitted at 1000Mbps
Amber On Port speed 10/100Mbps link up
Blinking Data Transmitted at 10/100Mbps
SFP
LINK/
ACT
Green On Port link up
Blinking Data transmitted