Comnet RLXE4GE24MODMS User manual

INSTALLATION AND OPERATION MANUAL
RLXE4GE24MODMS
HARDENED LAYER 3 MANAGED 10 GIGABIT
MODULAR ETHERNET SWITCH
The ComNet RLXE4GE24MODMS is a Layer-3 modular managed redundant ring
configurable Ethernet switch. It has four slots that can accommodate individual
modules that feature different combinations of SFP and electrical TX ports. One of
the slots can accommodate a 10 gigabit module with either 2 or 4 10 Gbps or 1 Gbps
SFP ports. The switch is designed for security, ITS, power substation and rolling stock
applications, and is fully compliant with the requirement of IEC 61850-3 and IEEE
1613 as well as NEMA TS1/TS2. The RLXE4GE24MODMS switch supports multiple
Ethernet Redundancy protocols, including C-Ring (recovery time < 30ms over 250
units of connection) and MSTP (RSTP/STP compatible). This switch can protect critical
applications from network interruptions or temporary malfunctions with its fast
recovery technology. This environmentally hardened switch is designed for direct
deployment in difficult out-of-plant or roadside operating environments.

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 2
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Contents
About This Guide 5
Related Documentation 5
About ComNet 5
Website 5
Support 5
Safety 5
Overview 6
Introduction 6
Software Features 7
Hardware Features 8
Hardware Installation 9
Installing RJ-45 Module in RLXE4GE24MODMS 9
Installing SFP Module in RLXE4GE24MODMS 9
Installing 10 Gbps SFP+ Module in RLXE4GE24MODMS 10
Installing Power Module in RLXE4GE24MODMS 10
Hardware Overview 11
Front Panel 11
Power Panel 13
Rack mount kit assembly 14
Ethernet Cables 15
1000/100BASE-TX/10BASE-T Pin Assignments 15
SFP 16
Console Cable 17
WEB Management 18
Configuration by Web Browser 18
About Web-based Management 18
Basic Setting 21
System Information 21
Admin & Password 22
Auth Method 23
IP Setting 24

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 3
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
RIP 25
VRRP 26
SSH 27
LLDP 28
Backup/Restore Configuration 32
Firmware Update 32
DHCP Server 32
Port Setting 34
Port Trunk 35
LACP 37
Redundancy 41
MSTP 42
STP 48
VLAN 51
VLAN Setting Example 56
Voice VLAN 62
Voice VLAN OUI 64
SNMP 65
Traffic Prioritization 71
Multicast 85
Security 89
AAA 93
RADIUS Overview 95
TACACS+ Server Configuration Help 106
Warning 107
System Warning 108
Monitor and Diag 110
Port Statistic 113
System Log Information 116
Cable Diagnostics 117
SFP Monitor 118
Ping 119
Syncronization-PTP 120
Factory Defaults 122
System Reboot 122

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 4
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Command Line Interface Management 123
About CLI Management 123
Commander Groups 127
Using the Routing Function 141
Static Routing Setting Example 141
RIP Routing Setting Example: 144
VRRP Setting Example 147

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 5
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
About This Guide
This guide is intended for different users such as engineers, integrators, developers, IT managers,
and technicians.
It assumes that users have some PC competence and are familiar with Microsoft Windows
operating systems and web browsers such as Windows Internet Explorer and Mozilla Firefox, as
well as have knowledge of the following:
»Installation of electronic equipment
»Electrical regulations and guidelines
»Knowledge of Local Area Network technology
Related Documentation
The following documentation is also available:
»RLXE4GE24MODMS Data sheet
»SFP Modules Data sheet
About ComNet
ComNet develops and markets the next generation of video solutions for the CCTV, defense, and
homeland security markets. At the core of ComNet’s solutions are a variety of high-end video
servers and the ComNet IVS software, which provide the industry with a standard platform for
analytics and security management systems enabling leading performance, compact and cost
effective solutions.
ComNet’s products are available in commercial and rugged form.
Website
For information on ComNet’s entire product line, please visit the ComNet website at
http://www.comnet.net
Support
For any questions or technical assistance, please contact your sales person ([e-mail]) or
the customer service support center ([e-mail])
Safety
»Only ComNet service personnel can service the equipment. Please contact ComNet Technical
Support.
»The equipment should be installed in locations with controlled access, or other means of
security, and controlled by persons of authority.

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 6
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Overview
Introduction
The RLXE4GE24MODMS is a Layer-2/3 modular managed redundant ring Ethernet switch with 4
slots. This switch is designed for industrial applications, power substation applications and rolling
stock applications, RLXE4GE24MODMS is compliant with the requirement of IEC 61850-3 and
IEEE 1613. RLXE4GE24MODMS supports Ethernet Redundancy protocol, C-Ring (recovery time <
30ms over 250 units of connection) and MSTP (RSTP/STP compatible). It can protect your mission-
critical applications from network interruptions or temporary malfunctions with its fast recovery
technology. Wide operating temperature ranges of -40 to +75ºC (when the proper 10 Gbps
module is in use) are supported.
RLXE4GE24MODMS can also be managed centrally and conveniently by using eConsole software
or via the Web-based interface, Telnet or console (CLI) configuration. The RLXE4GE24MODMS
switch is one of the most reliable choices for highly-managed and Fiber Ethernet power substation
and rolling stock applications..

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 7
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Software Features
»Designed for power substation / Railway application and fully compliant with the requirement
of IEC 61850-3 and IEEE 1613
»Modular design makes network planning and upgrades easy
»Supports Layer 3 static routing, RIP and VRRP function
»C-Ring (recovery time < 30ms over 250 units of connection)
»MSTP (RSTP/STP compatible) for Ethernet Redundancy
»IEEE 1588v2 clock synchronization
»Provides HTTPS/SSH protocol to enhance network security
»IP-based bandwidth management
»application-based QoS management
»Device Binding security function
»IGMP v2/v3 (IGMP snooping support) for filtering multicast traffic
»SNMP v1/v2c/v3 & RMON & 802.1Q VLAN Network Management
»ACL, TACACS+ and 802.1x User Authentication for security
»9.6K Bytes Jumbo Frame
»SFP ports support DDM function
»Multiple notification for warning of unexpected event
»Web-based Telnet, Console (CLI), and Windows utility (eConsole) configuration
»LLDP Protocol

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 8
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Hardware Features
»Supports redundant Power Inputs (Modular DC/AC Power, supports two power modules in
redundant operation)
»Supports maximum 3 slots 8 x 10/100/1000Base-T(X) RJ-45 Module
»Supports maximum 3 slots 8 x 100/1000Base-X SFP Module
»Supports maximum 1 slot 2/4 x 10G SFP+ Module or 2/4 x 1G SFP+ Module
»19 inch rack mountable design
»Operating Temperature: -40 to +75º C (Proper 10 Gbps SFP+ module used) or -40 to 85º C (10
Gbps SFP+ module absent)
»Storage Temperature: -40 to 85º C
»Operating Humidity: 5% to 95%, non-condensing
»Console Port (RJ45) : Baud Rate 115200 bps, 8, N, 1
»Dimensions : 440(W) × 325 (D) × 44 (H) mm

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 9
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Hardware Installation
Installing RJ-45 Module in RLXE4GE24MODMS
Each RLXE4GE24MODMS Switch supports a maximum of three RJ-45 Modules. To install the
module users must turn off the RLXE4GE24MODMS Power and plug-in the RJ-45 Module into Slot
1 ~ Slot 3.
Once installed turn on the power.
Installing SFP Module in RLXE4GE24MODMS
Each RLXE4GE24MODMS Switch supports a maximum of three SFP Modules. To install the
module users must turn off the RLXE4GE24MODMS Power and plug-in the SFP Module into Slot 1
~ Slot 3.
Once installed turn on the power.

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 10
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Installing 10 Gbps SFP+ Module in RLXE4GE24MODMS
Each RLXE4GE24MODMS Switch supports a maximum of one 10G SFP+ Module. To install the
module users must turn off the RLXE4GE24MODMS Power and plug-in the SFP Module into Slot 4.
Once installed turn on the power.
Installing Power Module in RLXE4GE24MODMS
Each RLXE4GE24MODMS Switch supports a maximum of two Power Modules. To install the power
module users must turn off the RLXE4GE24MODMS Power and plug-in the Power Module to Slot
1 or or Slot 2 (Either one or two modules can be installed).
Once installed turn on the power.

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 11
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Hardware Overview
Front Panel
RLXE4GE24MODMS supports four different module types.
Module Description
RLXE4GE24MODMS/HV RLXE4GE24MODMS Chassis With Dual High Voltage Power Supplies
RLXE4GE24MODMS/LV RLXE4GE24MODMS Chassis With Dual Low Voltage Power Supplies
RLXE4GE24MODMS/8TX 8 x 10/100/1000Base-T(X)
RLXE4GE24MODMS/8SFP 8 x 100 / 1000 Base-X
RLXE4GE24MODMS/XE2SFP 2 x 10G SFP+
RLXE4GE24MODMS/XE4SFP 4 x 10G SFP+
1. Front Panel LED Status:
LED for PW1: When the PWR1 links, the green led will be light on.
LED for PW2: When the PWR2 links, the green led will be light on.
LED for PWR: This LED lights on when the power module is activated.
LED for R.M. (Ring master): When the LED lights on, this switch is designated as the ring master of the
C-Ring topology.
LED for Ring: When the LED light on, the C-Ring is activated.
LED for Fault: Indicates unexpected event occurred.
LED for DEF: System resets to default configuration.
LED for RMT: System resets to default configuration.
2. Status by port LED , support three types LED Status .
LINK Status : Port show link status
SPD Status : Port LED show Speed status
FDX Status : Port LED show Duplex status
3. Console port (RJ-45)
4. Buttons
Reset Button : Push the button 3 seconds for reset; 5 seconds for factory default.
Mode Button : Push the button to change the Port LED Mode .
5. RJ-45 / SFP Module Slot.
6. 10G SFP+ Module Slot.

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 12
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
RJ-45 Module
8 × 10/100/1000Base-T(X)
SFP Module
8 × 100/1000Base-X SFP
10 Gbps Module
4 × 10 Gigbit SFP
Power Module

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 13
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Power Panel
RLXE4GE24MODMS are redundant power switches with support for two power inputs.
Note: At the factory, power GND and chassis GND are connected as shown in the picture below.
RLY CM: Relay Common
RLY NO: Relay Normally Open
RLY NC: Relay Normally Closed

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 14
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Rack mount kit assembly
You can find the rack mount kit and the screws in the packing box. Please assembly the rack
mount kit on the switch with screws as shown below:

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 15
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Ethernet Cables
The RLXE4GE24MODMS series switches have standard Ethernet ports. According to the link type,
the switches use CAT 3, 4, 5,5e UTP cables to connect to any other network device (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable specifications.
Cable Types and Specifications
Cable Type Max. Length Connector
10BASE-T Cat. 3, 4, 5 100-ohm UTP 100 m (328 ft) RJ-45
100BASE-TX Cat. 5 100-ohm UTP UTP 100 m (328 ft) RJ-45
1000BASE-TX Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328ft) RJ-45
1000/100BASE-TX/10BASE-T Pin Assignments
With 1000/100BASE-TX/10BASE-T cable, pins 1 and 2 are used for transmitting data, and pins 3
and 6 are used for receiving data.
10/100 Base-T(X) RJ-45 Pin Assignments
Pin
Number Assignment
1TD+
2TD-
3RD+
4Not used
5Not used
6RD-
7Not used
8Not used
1000 Base-T RJ-45 Pin Assignments
Pin
Number Assignment
1BI_DA+
2BI_DA-
3BI_DB+
4BI_DC+
5 BI_DC-
6 BI_DB-
7BI_DD+
8 BI_DD-

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 16
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
The RLXE4GE24MODMS Series switches support auto MDI/MDI-X operation. You can use a
straight-through cable to connect PC to switch. The following table below shows the 10BASE-T/
100BASE-TX MDI and MDI-X port pin outs.
10/100 Base-T MDI/MDI-X pins assignment
Pin
Number MDI port MDI-X port
1TD+(transmit) RD+(receive)
2TD-(transmit) RD-(receive)
3RD+(receive) TD+(transmit)
4Not used Not used
5Not used Not used
6RD-(receive) TD-(transmit)
7Not used Not used
8Not used Not used
1000 Base-T MDI/MDI-X pins assignment
Pin
Number MDI port MDI-X port
1BI_DA+ BI_DB+
2BI_DA- BI_DB-
3BI_DB+ BI_DA+
4BI_DC+ BI_DD+
5 BI_DC- BI_DD-
6 BI_DB- BI_DA-
7BI_DD+ BI_DC+
8 BI_DD- BI_DC-
Note: “+” and “-” signs represent the polarity of the wires that make up each wire pair.
SFP
The Switch has fiber optical ports with SFP connectors. The fiber optical ports are in 100/1000Base-X
multi-mode (0 to 550M, 850 nm with 50/125 μm, 62.5/125 μm fiber) , single-mode and 10 Gbps SFP+
Module with LC connector. Please remember that the TX port of Switch A should be connected to the
RX port of Switch B.
Switch A Fiber Cord Switch B

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 17
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Console Cable
RLXE4GE24MODMS switches can be managed by the console port. The DB-9 to RJ-45 cable
can be found in the package. You can connect them to a PC via a RS-232 cable with DB-9 female
connector and the other end (RJ-45 connector) connects to console port of the switch.
5
9
1
6
1
6
5
9
DB-9 Male DB-9 Female
PC pin out (male) assignment RS-232 with
DB-9 female connector DB-9 to RJ-45
Pin #2 RD Pin #2 TD Pin #2
Pin #3 TD Pin #3 RD Pin #3
Pin #5 GD Pin #5 GD Pin #5
Pin Male Connector Female Connector
1Received Line Signal Detect (Received by DTE
Device)
Received Line Signal Detect (Transmitted from
DCE Device)
2Received Data (Received by DTE Device) Transmitted Data (Transmitted from DCE Device)
3Transmitted Data (Transmitted from DTE Device) Received Data (Received by DCE Device)
4DTE Ready (Transmitted from DTE Device) DTE Ready (Received by DCE Device)
5Signal Ground Signal Ground
6DCE Ready (Received by DTE Device) DCE Ready (Transmitted from DCE Device)
7Request to Send (Transmitted from DTE Device) Clear to Send (Received by DCE Device)
8Clear to Send (Received by DTE Device) Request to Send (Transmitted from DCE Device)
9Ring Indicator (Received by DTE Device) Ring Indicator (Transmitted from DCE Device)

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 18
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
WEB Management
Attention: While installing and upgrading firmware, please remove physical loop connection first.
DO NOT power off equipment while the firmware is upgrading!
Configuration by Web Browser
This section introduces the configuration by Web browser.
About Web-based Management
An embedded HTML web site resides in flash memory on the CPU board. It contains advanced
management features and allows you to manage the switch from anywhere on the network
through a standard web browser such as Microsoft Internet Explorer.
The Web-Based Management function supports Internet Explorer 5.0 or later. It is based on Java
Applets with an aim to reduce network bandwidth consumption, enhance access speed and
present an easy viewing screen.
Note: By default, IE5.0 or later version does not allow Java Applets to open sockets. You need
to intentionally modify the browser setting in order to enable Java Applets to use network
ports.
Preparing for Web Management
IP Address: 192.168.10.1
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.10.254
User Name: admin
Password: admin

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 19
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
System Login
1. Launch Internet Explorer.
2. Type http:// and the IP address of the switch. Press “Enter”.
3. The login screen appears.
Login screen
4. Key in the username and password. The default username and password is admin.
5. Press OK button, then the main interface of the Web-based management appears.

INS_RLXE4GE24MODMS_REV– 1 Jul 2016 PAGE 20
INSTALLATION AND OPERATION MANUAL RLXE4GE24MODMS
TECH SUPPORT: 1.888.678.9427
Main Interface
Main interface