compulocks PMDOCK01 User manual

Mounting Options
Assembly Instructions
PowerMove Dock Station SKU: PMDOCK01
2 Counter Stand Mounting
USE M4 x 10mm PIN-IN-TORX
BUTTON HEAD SCREWS PROVIDED.
TIGHTEN USING PROVIDED
TORX SCREWDRIVER
4 Direct Mounting To Wall
MOUNTING SCREWS
NOT PROVIDED
3 Wall Arm Mounting
USE M4 x 10mm PIN-IN-TORX
BUTTON HEAD SCREWS PROVIDED.
TIGHTEN USING PROVIDED
TORX SCREWDRIVER
1 Floor Stand Mounting
USE M4 x 10mm PIN-IN-TORX
BUTTON HEAD SCREWS PROVIDED.
TIGHTEN USING PROVIDED
TORX SCREWDRIVER
Optional Add-On:
Portrait To Landscape Rotation Plate
USE M4 x 10mm PIN-IN-TORX BUTTON
HEAD SCREWS PROVIDED TO
FIX TO ROTATION PLATE. TIGHTEN USING
PROVIDED TORX SCREWDRIVER.
USE SCREWS PROVIDED WITH ROTATION PLATE
TO SECURE TO STAND or ARM
www.compulocks.com | [e-mail] | [phone] Sheet 1 of 3
©Compulocks Brands Inc. All Rights Reserved

Placing Tablet with Connector to Dock Station
Assembly Instructions
PowerMove Dock Station SKU: PMDOCK01
www.compulocks.com | [e-mail] | [phone] Sheet 2 of 3
©Compulocks Brands Inc. All Rights Reserved
Removing Tablet with Connector from Dock Station
1 2 3 4
1 2 34
USE KEY TO UNLOCK THE LOCK.
REMOVE KEY ALIGN CONNECTOR TO DOCK STATION
PUSH LOCK BUTTON TO SECURE
TABLET TO DOCK STATION
PRIOR TO PULLING LATCH,
UNLOCK LOCK USING KEY
APPLY LIGHT PRESSURE.
LATCH WILL ENGAGE
PULL LATCH FORWARD GENTLY PULL UP TO RELEASE

Assembly Instructions
PowerMove Dock Station SKU: PMDOCK01
www.compulocks.com | [e-mail] | [phone] Sheet 3 of 3
©Compulocks Brands Inc. All Rights Reserved
Tablet Data and Charge PD CompatibleTablet Charge PD Compatible
CHARGING CUBE/POWER SUPPLY
(NOT INCLUDED)
PMDOCK01 HAS A
FEMALE USB-C CONNECTOR
NOTE:
A HIGHER WATTAGE POWER SUPPLY MAY BE
REQUIRED FOR PROPER TABLET CHARGING
WHEN USING A HUB THAT REQUIRES POWER.
DO NOT EXCEED THE HUBS MAXIMUM
RATED INPUT POWER.
USB-C POWERED HUB
IN THE BOX
Keys Hardware Kit PowerMove Dock Station

3
21
4
Assembly Instructions
PowerMove Connector SKU: PMCON01
www.compulocks.com | [e-mail] | [phone] Sheet 1 of 2
©Compulocks Brands Inc. All Rights Reserved
130mm
130mm
USING ALCOHOL PAD PROVIDED,
CLEAN 130mm SQUARE AREA CENTERED ON THE BACK OF THE TABLET.
ALLOW TO AIR DRY
PORTRAIT LANDSCAPE
SELECT THE ORIENTATION
OF THE CONNECTOR ON THE TABLET
INSTALL RIGHT ANGLE USB-C CABLE
AS SHOWN
PASS CONNECTOR THROUGH CASE*
AND INSTALL CASE ON TABLET
*CASE SOLD SEPARATELY

65
Assembly Instructions
PowerMove Connector SKU: PMCON01
www.compulocks.com | [e-mail] | [phone] Sheet 2 of 2
©Compulocks Brands Inc. All Rights Reserved
REMOVE COVERS TO EXPOSE
ADHESIVE ON ALL 4 PADS
IN THE BOX
NOTE:
TABLET AND CONNECTOR SHOULD BE AT
ROOM TEMPERATURE FOR BEST RESULTS
CENTER CONNECTOR ON OPENING
IN CASE AND ADHERE TO TABLET WITH MILD PRESSURE
FEED CABLE UNDER CASE
AS NEEDED
FOR BEST PERFORMANCE ALLOW
CONNECTOR TO BOND TO TABLET FOR 12 HOURS.
Alcohol Wipes PowerMove Connector