Comsec Protection Systems UP-200 GSM User manual

Comsec Protection Systems
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e

-
-
-
-
-
Comsec Protection Systems
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e

-
Comsec Protection Systems
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e

UP200-GSM Rev.2.4 18/10/2014
UP200-GSM-RD
Intercom and access control unit
operating on mobile GSM network
INTRODUCTION
The UP200-GSM-RD is an intercom unit which, as a
cell phone,can call the owner’s mobile or landline
phone. By pressing the call button on the intercom, it
makes the voice connection in a few seconds, just like
when talking via a conventional intercom system. This
way it makes it possible for the owner to receive the
visitor’s calls and talk to them at any time and any
where, even when not at home.
The unit does not need any special installation or
complicated wiring; it needs power only and an active
SIM card.The unit brings communication between the
owner and visitor to a higher level and so improves
the traditional solution, which can only make a
connection between the gate and the house.
FUNCTIONS
Wireless intercom with 1 pushbutton
Two phone numbers can be assigned to each
pushbutton (set as primary and secondary)
Gate control function by free call, 100 user phone
numbers can be configured
The electric strike can be controlled using the
phone’s keys during a conversation, or on the
scene using an external pushbutton.
SMS forwarding (e.g. to forward the balance
information of pre-pay SIM card)
Simple configuration via USB using the PC
software provided in the intercom
Remote configuring by SMS message
FEATURES
Compact design, all functions on 1 panel
Power voltage range 9-30V
1 contact input
1 relay output, max load: 5A@30V
1 voltage output with short circuit and overcurrent
protection, max power: 1A@
Programming port: mini USB B type
Communication: GSM 900/1800 MHz (2G)
Network independent, accepts any SIM card
Operating temperature: -30°C / +60°C
Protection: IP54
APPLICATION AREA
Modern solution for wireless intercom system
(private homes, resorts, offices, premises)
Remotely controllable access control unit
Keyless door opening
Garage door opening/closing by phone
Emergency call unit
Infoformation columns
ADVANTAGES
No missed clients or visitors, since the intercom
unit calls the owner’s mobile phone, no matter
where the owner is.
On call, the owner can let in the guest, client or
courier remotely.
In case of absence, burglary attempts can be
prevented by imitating the apparent presence.
Fast and easy installation, easy configuration
using a PC.
Possibility for communication from any fixed place.
Comsec Protection Systems.
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e

UP200-GSM Rev.2.4 18/10/2014
OPERATION
Visitor mode
When the visitor pushes the call button, the device
initiates a voice call to the configured phone number.
If the called party accepts the call, the communication
establishes for the configured duration. During the
call, the connection cannot be interrupted neither by
making a call to the device, nor by pressing the button
again. The call is ended automatically when the
configured communication time expires, or the called
party can hang up the call at anytime on his/her
phone. The call is ended automatically if the called
party does not answer or is not available.
A new call is initiated only if the button is pressed
again.
Listen-in mode
The intercom unit can be called from the telephone
numbers assigned to the telephone’s push buttons. If
the call is initiated from any other telephone number,
the intercom rejects it. In this case the unit accepts the
call without ringing and the voice connection
establishes. The call can be ended on the caller’s
phone or by pressing the call button on the unit.
If the call is initiated from a phone number which
is configured in the unit as gate opener number,
the device will consider the call as a gate opening
call. In this case voice connection is not
established, but the relay output is activated.
Controlling the relay output
The RELAY (normally open, NO) relay output can be
controlled as follows, depending on the usage:
controlling by free call:
on incoming call, after identifying the caller ID, the
unit rejects the call and activates the output
e.g. garage door or barrier opening, for which a
maximum of 100 user phone numbers can be
configured
controlling by the pushbutton:
the relay activates when the call button is pushed
e.g. possibility to connect an existing door bell
controlling by the INPUT contact input:
the relay activates on external contact
e.g. garage door opening or closing
controlling by the phone’s keys:
while in call by pressing 2# of the phone’s
numbered keys the relay activates for the
configured time period
ATTENTION:
The RELAY and –OUT+ outputsare activated in
parallel and independently from each other by
both menu items, the Control of outputs and the
Gate control.Please take this into consideration
when planning the usage!
Controlling via the voltage output
The OUT+ voltage output can be used for the direct
control of an electric strike as follows:
controlling by the pushbutton:
the output activates by pressing the pushbutton
controlling by the INPUT contact input:
after activating the input, the output activates for the
configured time period
controlling by the phone’s keys:
while in call by pressing 1# of the phone’s
numbered keys the output activates for the
configured time period
The output voltage is almost equal with the supply
voltage, which provides easy usability with 12VDC or
24VDC systems. The output is protected against short
circuit and overcurrent, the output turns off upon
overcurrent and becomes operative again after the
termination of the fault.
Forwarding incoming SMS messages
The unit forwards the SMS messages received on its
SIM card (e.g. balance information in case of a prepaid
card) to the configured phone number. After forwarding,
the received message is deleted from the SIM card. If
there is no phone number configured, the unit deletes
the incoming messages without forwarding.
Status LED indications
LED Color
GSM OK green
Is lit after connecting to the
GSM network and reaching the
sufficient GSM signal.
The sufficient signal is: 10
(on 0-31 scale)
ERROR red
Is lit continuously if the device
cannot connect to the GSM
network.
Possible reasons:
-the GSM antenna is faulty or
is not connected
-the SIM card is not inserted,
-or the PIN code request is
not disabled,
-or the SIM card is faulty.
CONNECTING green
Communication in progress.
A call or conversation is in
progress.
OUT+ red Voltage output activated
RELAY red Relay output activated
Comsec Protection Systems.
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e

UP200-GSM Rev.2.4 18/10/2014
SETTING WITH MS WINDOWS APPLICATION
The intercom unit parameters (phone numbers, controls) can be configured using the Intercom configurator
software found on the internal storage of the device. You can run the program directly from the unit’s drive after
connecting to USB (Widows XP, Windows 7and Windows 8compatible). Connect the USB port of the GSM
Intercom to the PC using the supplied cable and run the Intercom configurator software!
Important note: in most cases the power of the USB connector is only sufficient to make the settings; therefore, it is
necessary to connect an external powersupply for testing the setup!
Comsec Protection Systems.
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e

UP200-GSM Rev.2.4 18/10/2014
Adminis
tration operations
These menu items serve for reading, writing, saving
etc. the settings.Using the functions displayed in the
below picture it is possible to read and write the unit’s
memory and the settings , as well as save settings to
PC or open and edit a file with the existing settings.
The procedure to be followed in all cases:
1. By connecting to the PC via USB and clicking on
„Read”button, the software reads and displays
the intercom’s settings.
2. After editing the settings and clicking on Write the
unit uploads the date to the intercom and starts
operating.
3.
It is also possible to save data to the PC.
Buttons
The intercom unit calls the phone numbers entered
here when the appropriate button is pressed. If both
phone numbers are set to any button, the unit calls
the primary phone number first, and if the call is
successful, it ignores the secondary telephone
number. In case of an unsuccessful call (e.g. if the
called number is not available or the call is not
accepted), calling the secondary phone number can
be done by pushing the button again (within 60
seconds). If the Automatic option is enabled, then
the unit calls the secondary phone number if the
primary fails without having to push the button again.
Control of outputs
The two outputs of the unit can be controlled by multiple
configured events. You can choose the activation event
according to the usage.
OUT
The voltage output, e.g. for direct control of an electric
lock.
RELAY
The relay contact output, e.g. for garage door control.
Setting:
1. To enable control, it is necessary to tick the chosen
output or outputs.
2. At the next step you need to select the starting event
which will activate the output.
3. At last the default control needs to be set, where
NO= OFF, NC= ON by default.
In case of OUT NO= 0V, NC= power.
In case of RELAY NO= break, NC= short-circuit
At control the output changes state for the given time
period.
General settings
Ring time (10-120 sec)
The maximum time allowed for ringing from pushing the
call button. This function is useful to avoid switching to
voicemail.
Call time (10-600 sec)
The maximum time allowed for a call initiated from the
intercom.
Read
Click to read and displays the
settings from the unit.
Write
Click to write the settings to the
unit’s memory.
Save
Click to save the settings to file.
Open
Click to open saved settings from
file.
Firmware
Click to update the intercom’s
firmware.
SIM PIN
Insert the PIN of the SIM card that
is used in the intercom
Comsec Protection Systems.
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e

UP200-GSM Rev.2.4 18/10/2014
OUT
active time
(1
-
120 sec, monostabl
e
)
The voltage output activation time.
RELAY active time (1-120 sec, monostable)
The relay contact output activation time.
SMS forward
Forwards the SMS messages received on the unit’s
SIM card to the specified phone number, e.g. balance
information received from the GSM service provider. It
is recommended to configure this in the case of using a
pre-pay type SIM card.
Microphone sensitivity (5-15), default value: 13
the change in settings becomesvalid in next call
progress
Volume (10-100), default value: 35
the change in settings becomesvalid in next call
progress
Attention: By increasing the default values of the
microphone and speaker settings, echo effect may
occur and increase!
If the value of volume is increased it is necessarey to
decrease the value of the microphone sensitivity to
stop feedback. In the same way, if the value of
microphone sensitivity is increased decrasing the
volume can be the solution to suppress feedback.
Backlight brightness
light (0-10), default value: 5
Gate control
When calling the intercom from the phone numbers
specified here, control of the output or outputs
assigned to the given phone number is performed. The
incoming call is not accepted from the configured
telephone number, so this function operates with a free
call. A maximum of 100 user phone numbers can be
added.
Status information
Displays information about the switching state of the
peripherals and the actual status of the mobile network.
Intercom information
Displays the module type and the firmware version.
Inputs
Displays information on the state of the intercom’s
buttons (upper and lower) and shows the state of the
external control input (INPUT).
GSM network
Displays the GSM provider and the level of the GSM
signal (0-31)
The appropriate GSM signal is minimum 12
Outputs
Displays the state of the relay and voltage output
control.
State messages
The messages shown in this window give information
about the internal operation of the unit. This helps in
identifying an internal process, an incorrect
configuration or other malfunction.
The question marks placed next to the settings in
the Intercom configurator give assistance to the
parameter settings of the given section.
Comsec Protection Systems.
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e

UP200-GSM Rev.2.4 18/10/2014
SETTING WITH SMS COMMANDS
Configuration of the unit is possible by sending the appropriate commands in SMS to the module’s phone number.It
is possible to send more commands (settings) in the same SMS, but the length of the message must not exceed 140
characters! Each message must begin with the password using the PWD=password#command and each command
must end with #character, else the module does not apply the modifications. The following table contains the
configuring and query commands:
Configuration commands
PWD=1234#Password for programming, default setting:1234
PWC=new password #Changing the password. The password is a 4-digit number.
RESET# Resetting the settings and the password to default.
UPTEL1=phone number#Primary phone number for upper pushbutton.
UPTEL2=phone number#Secondary phone number for upper pushbutton.
UPAUTO=ON# vagy OFF# In case the call to UPTEL1 fails, UPTEL2 phone number will be called without
having to push the button again, if the parameter is ON.
LOWTEL1=phone number#Primary phone number for lower pushbutton.
LOWTEL2=phone number#Secondary phone number for lower pushbutton.
LOWAUTO=ON# or OFF# In case the call to LOWTEL1 fails, LOWTEL2 phone number will be called
without having to push the button again, if the parameter is ON.
OUT=activation event#
Voltage output control: OFF: disable, BUTTON: when button is pressed
INPUT: when input is activated, PHONE: during call, pressing any of the phone’s
keys, IN+PHONE: INPUT and PHONE enabled
RELAY=activation event#Relay control: OFF: disable, BUTTON: when button is pressed
INPUT: when input is activated
RINGTIME=duration#Ringing time of the telephone to restrict the reach of voice mail. (10-120sec)
CALLTIME=duration#Maximum duration of the conversation. (10-600 sec)
RTIME=duration*NO# or NC Duration and idle mode of the relay output activation. (1-120 sec) NO=off,
NC=on
OUTTIME=duration*NO# or NC Duration and idle mode of the voltage output activation. (1-120 sec) NO=off,
NC=on
RTEL=phone
number*REL*OUT#
Setting the phone numbers f
or relay or voltage output activation. For output
activation the suffix after the phone number is necessary.
*REL: switch the relay, *OUT: switch the voltage out,
*REL*OUT switch both. Up to 100 users.
RTELDEL=phone number#Delete the selected phone number frm the RTEL list.
STATUS?# Query of the settings,except for the RTEL list.
INFOSMS=phone number#Forwards the balance information of the GSM provider to the given telephone
number.
This scenario shows the configurations for the following requirements: phone number 2 only for upper pushbutton,
auto switch to the secondary phone, VOUT control (for electric lock) by phone and input contact, duration is 10sec,
both phone numbers are able to control the gate control’s relay by a free call, relay activation time is 5sec.
Other call parameters: Ringingtime=25sec; maximum duration of the conversation=120sec; forwarding prepaid card
information to primary phone number
SMS message:
PWD=1234#UPTEL1=0036309999999#UPTEL2=0036201111111#UPAUTO=ON#OUT=IN+PHONE#
OUTTIME=10*NO#RTEL=0036309999999*REL#RTEL=0036201111111*REL#RTIME=5*NO#
RINGTIME=25#CALLTIME=120#INFOSMS=0036201111111#
Comsec Protection Systems.
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e

UP200-GSM Rev.2.4 18/10/2014
INSTALLATION
Putting into operation
Disable PIN code request on the SIM card, for which a
mobile telephone is necessary.
Make sure the SIM card is inserted properly into its
case.
Inserting the SIM card: push the metallic part of the SIM
case towards the direction of the arrow to open up the
SIM slot for inserting the card. Insert the SIM card into
the slot so that its contact surface pointstowards the
contact pins of the card case when turned down, also
the cut corner of the card should fit into the plastic case.
Fasten the SIM card by pulling back the metallic part of
the SIM case.
Make sure the antenna is fixed properly into the SMA
connector.
Make sure the wires are connected as shown in the
connection diagram.
Make sure the power supply is sufficient for the
operation of the unit! If it is, and all connections are
done, the unit can be powered up.
When operated with an electric lock, the minimum
power requirement is 15VA!
Connection diagram
Mounting
Do not mount the unit where it could be affected by
strong electromagnetic disturbances.
Antenna: the GSM antenna supplied with the unit
provides good transmission under normal
reception circumstances. In case of having signal
strength problems and/or noisy communication,
use another type of higher gain antenna or find a
more suitable place for the antenna.
INPUT, CODE
inputs and
OUT+
output are defined to
the COM common negative point, so they need to be
installed in pair with COM cable.
①GSM antenna connector
②Contact input
③Relay contact output
④Voltage output
⑤Power input
⑥Speaker output
⑦Microphone input
⑧Battery connector
solar powered version only!
⑨Name plate lighting
⑩USB mini B port
⑪Call pushbuttons
⑫Status LEDs
⑬SIM card case
⑭ Coded control output
not supported function
⑮ Common negative point
Comsec Protection Systems.
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e

UP200-GSM Rev.2.4 18/10/2014
TECHNICAL SPECIFICATION
Name
Other conditions
Minimum
Typical
Maximum
Unit
Power supply
(DC_IN)
9
12
/ 24
30
VDC
Current consumption
in case of 12VDC
3
0
4
0
400
mA
Relay output load
24
V
30
V
5
A
Voltage output
DC_IN
–
1V
V
1
A
Contact input switching
0
0
100
Ohm
Operating temperature
-
30
+60
°C
Outdoor protection
IP5
4
Package contents
UP200-GSM-RD
GSM 900MHz / 1800MHz antenna
USB A / B5 mini cable
Antenna bracket + fixing screws
Other data
Transmission frequency GSM850 / EGSM900
DCS1800 / PCS1900
Dimensions height:165mm
width:122mm
depth: 40mm
Comsec Protection Systems.
C O M S E C P R O T E C T I O N S Y S T E M S L T D .
U N I T 2 6 , S T A D I U M B U S I N E S S P A R K , • B A L L Y C O O L I N R O A D , • D U B L I N 1 1
P H O N E : ( 0 1 ) 8 8 5 3 0 0 8 • F A X : ( 0 1 ) 8 8 5 3 0 0 7
E M A I L : i n f o @ c o m s e c . i e • W E B : h t t p : / / w w w . c o m s e c . i e