Vimar 41002 User manual

Use and Configuration Manual
41002 - 41005
Due Fili Plus audio, audio/video units

2
41002 - 41005

3
41002 - 41005
General information 4
Description 4
Warnings and advice 5
Keys and status LEDs 6
Status LEDs 7
Operation 8
Functions 9
Pan/Zoom function (only for 41005) 9
Picture control (41005) 10
Dusk/dawn function 10
Teleloop and control voice synthesis function 10
Configurations 11
Installer menu 12
Using the push buttons to navigate the menu 12
LEDs and menu structure 13
Selecting order of push button modules 14
Push button remapping 16
Automatic procedure for assigning IDs to Indoor Stations 17
Automatic procedure for assigning IDs to Outdoor Stations 18
Set lock time 19
Set talk time 20
Setting the audio level 21
Reset factory settings/Restart/Reset internal memory 22
Reset factory settings 23
Restart entire system 24
External memory reset 24
Setting push button behaviour according to the call button 25
Camera enabling (only 41002) 27
Common locks 28
Advanced configuration with SaveProg software 30
Index

4
41002 - 41005
Audio electronic unit with input for CCTV type external camera (41002) and audio/video electronic unit, wide-angle
teleloop (41005) for Pixel Series, Outdoor Stations, for use in systems with Due Fili Plus technology. Both are equipped
with:
• full-duplex audio with Larsen effect removal;
• automatic gain control on loudspeaker power output, according to the type of installation;
• four traditional call buttons to the Indoor Stations in two rows (2+2).
• input for optional local additional power supply unit (with power supply unit 6923)
The audio electronic unit with input for camera (41002) works by default as audio only.
Nevertheless, transmission of the video signal can be enabled via SaveProg or by following the “Configuration”
procedure described below (in chapter: Configuration - Camera enabling).
N.B.: When there is no video signal at the M-V terminals, any video entryphones that receive the call from this module
will switch on but will not show a valid image.
This is not a malfunction.
General information
Description
The audio/video version electronic unit (41005) is equipped with:
• cameras and white LED lighting in the recording area with automatic brightness control according to the ambient
light.
• camera with pan/zoom function controlled directly from the Indoor Station;
• two picture control modes: standard and portrait enhanced;
Hearing-impaired
function and voice
synthesis for visually
impaired users
Visual call signalling
Automatic
brightness
control
Echo canceller
and noise
reduction
Automatic gain
control
Camera with
wide-angle
lens.

5
41002 - 41005
Audio frequency function for hearing aids (Teleloop)
The electronic unit can be used by people wearing hearing aids.
For correct functioning of the hearing aid, please refer to its instruction manual.
Any metal objects or electronic equipment in the vicinity may affect the quality of the sound received by the hearing aid.
Warnings and advice
1.8 m
(83°)
1m
1,65m1,20 m
(41005)
2,6 m (104°)
1m
(41005)
1.8 m
(83°)
1m
1,65m1,20 m
(41005)
2,6 m (104°)
1m
(41005)

6
41002 - 41005
The TAB 7559 video entryphone can be operated using the touch keys described below.
Keys and status LEDs
1. LED for light signals, see Status LEDs
2. Mini USB connector for configuration via PC and specific software
3. Call buttons and Configuration
4 Speaker
5 Microphone
6 Recording area lighting LED
Camera (only 41005)
N.B.: the aesthetic finish is purely indicative
1
3 3
2
1
4
5
6 67

7
41002 - 41005
LED DESCRIPTION
When on, communication is active, when flashing the call is under way
When on, it signals the Bus is busy, when flashing communication was unsuccessful
It turns on when the lock is operated
Situation On (s) Period (s) Duration (s)
Attempt to call with BUS busy 0.1 0.2 2
Call to Indoor Station with ringtone mute 0.1 0.2 5
Call to Indoor Station busy 0.2 0.4 5
The Indoor Station called does not exist 0.1 0.2 1
Secondary ID assignment with parent > 50 0.1 0.2 1
Situation On (s) Period (s)
The chosen configuration has a value that
does not fall within the standard range (it was
changed with SaveProg)
0.1 0.5
Configuration is being reset to the factory value 0.1 0.2
Input for automatic ID assignment to Indoor
Stations pending choice of push button to
start with
0.5 1
The Outdoor Station is verifying whether another
one with the same ID exists 0.25 1
Pending verification whether another Outdoor
Station with the same ID exists
0.25
N.B.: they are offset by 0.25s from
one another, giving the impression of
clockwise rotation
1
Push button remapping The LED paired with the button to be
remapped remains permanently lit N.O.
Pending sorting of additional push button
modules 0.5 1
Some of the LEDs illustrated below only come on in certain conditions.
RED LED :
WHITE LEDS:
The situation of remaining in bootloader lasts 10 s from entry.
It exits automatically if the update is not started.
The situation is signalled by the green LED signalling active communication/call under way coming on, and if the electronic unit is powered
by BUS, simultaneously with the lighting of a single white LED, the bottom right one.
Status LEDs

8
41002 - 41005
Operation
N.B.: from this paragraph onwards, only the audio/video electronic unit 41005 will be illustrated; however, the functions
described also apply for the Audio electronic unit 41002, except where specified.
Calls to Indoor Stations
the audio/video electronic unit 41005 can manage up to 4 calls to Indoor Stations, using four traditional push buttons in
two rows (2+2) and, in combination with additional push button modules 41010 (41011), up to a maximum of 84 button
calls.
Lock release control and additional push buttons
An electrical lock connected directly to terminals S+ and S- can be controlled and an additional local push button to
release a door lock to terminals CA+ and CA-.
Alternatively to terminals CA+ and CA- they can be configured using the SaveProg software, as input of a sensor for
signalling “Door open”.
Dusk/dawn function
Dusk/dawn function for automatically adjusting the brightness according to the ambient light.
This adjustment affects the white LEDs lighting the recording area (only for 41005), and the key backlighting LEDs.
Teleloop
Hearing-impaired function for hearing aid wearers
Basic and advanced configuration
The basic configuration of the Electronic unit is possible using the 4 push buttons on the front and the related LEDs for
the following parameters:
• selecting order of push button modules, push button remapping and default grouping of push buttons;
• automatic configuration of Indoor Station and Outdoor Station addresses;
• lock/talk time and audio level setting;
• configuration of common locks
• reset factory settings and external memory;
• restart of all devices;
• camera enabling (41002).
Moreover, the Electronic unit can be configured in an advanced way using the SaveProg software.

9
41002 - 41005
This function of the Electronic Unit allows an Indoor Station with specific characteristics to zoom the image recorded by
the camera.
Please refer to SaveProg for configuration details.
Example of the pan/zoom function with Indoor Station Tab7549
Functions
Pan/Zoom function (only for 41005)
The device performs a zoom divided up into 5 zones
In both cases, once the sequence is finished, press the key again to return to the normal display
2. Press to display the zones in sequence anti-clockwise
3. Press to display the zones in sequence clockwise
23
1
3
4
5
2
3
4
2
1
5

10
41002 - 41005
The standard mode provides optimal operation in typical environmental conditions, while the enhanced portrait mode
highlights the caller in a backlit situation (such as at dawn).
Can be selected with SaveProg.
This lets you enable automatic brightness control of the Outdoor Station backlighting according to the ambient light
brightness.
Can be selected with SaveProg.
Electronic units 41002 and 41005 are ideal for people who are physically challenged, wear a hearing aid or are partially
sighted.
Enable the hearing aid, referring to its instruction manual.
Note: any metal objects or electronic equipment nearby may compromise the quality of the sound received by the
hearing aid.
Control voice synthesis can be enabled with SaveProg.
Picture control (41005)
Dusk/dawn function
Teleloop and control voice synthesis function
30 / 40 cm
30 / 40 cm