Comunello Mowin R1-Control User manual

Italian Movements
Italian Movements
R-CONTROL
FRAME AUTOMATION
ISTRUCTION
MANUAL

Italian Movements
Italian Movements
8
UP
STOP
DOWN
DIP-SWITCHES
PROG
L1
DIP-SWITCHES
UP
STOP
DOWN
PROG
L1
L2
L3
L4
L5
L6
SELC SELG
R1-CONTROL R6-CONTROL

Italian Movements
Italian Movements
9
ENGLISH
Please read carefully and follow the instructions detailed in this manual. Keep the manual for use and future
maintenance. Pay attention to the configuration of the DIP-switches, to the data concerning the performance
(see “Technical Data”).
The CE mark certifies that the trasmitter conforms to the essential health and safety requirements laid down
by European product directives. The CE mark can be identified by the relevant adhesive label applied to the
outside of the product, on which are shown some of the data shown in the following table:
1. GENERAL INFORMATION
2. TABLE OF TECHNICAL DATA AND MARK
R1-CONTROL R6-CONTROL
MX00 AT 01N 0G 00 MX00 AT 02N 0G 00
Power Supply 2 x Lithium 3V (CR2032 230mAh) 2 x Lithium 3V (CR2032 230mAh)
Frequency 434,15 MHz 434,15 MHz
Channels 1 6
Range in open field 300 mt 300 mt
Max . absorption < 25mA < 25mA
Dimensions 120x52x19 mm 120x52x19 mm
Weight 40g 40g

Italian Movements
Italian Movements
10
All the transmitters R1-CONTROL allow controlling 1 automation or group of automations for awnings and
shutters.
3.1 FUNCTIONING OF THE BUTTONS UP, DOWN AND STOP
UP Activates the automation GOING UP
DOWN Activates the automation GOING DOWN
STOP It stops the automation
3.2 FUNCTIONING OF THE BUTTON PROG AND DIP-SWITCHES
The button PROG and the DIPSWITCHES program the functions of the control units controlled by the
transmitters R1-CONTROL. Read carefully the section “PROGRAMMING OF THE FUNCTIONS BY R-CONTROL
TRANSMITTERS” in the handbook of the control unit or in the one of the tubular motor with integrated
electronic card.
3. TRASMITTER R1-CONTROL

Italian Movements
Italian Movements
11
ENGLISH
4.1 Functioning of the buttons UP, DOWN and STOP
UP Activates the automation GOING UP
DOWN Activates the automation GOING DOWN
STOP it stops the automation
4.2 Functioning of the button SELC
By this button it is possible to select the channel to be used for the radio transmission.
1. Press button SELC until selected the desired channel: the corresponding led is on for some seconds
2. Press one of the buttons UP, DOWN or STOP to transmit the control
To select all the channels at the same time press several times the button SELC until all the leds are on.
To display the channel set, press once the button SELC.
4.3 Functioning of the button SELG
By this button it is possible to program and select the GROUPS of channels to be used for the radio
transmission. It is possible to store up to 8 groups of channels; stored the eighth, a new group will replace
the first one.
1. Press the button SELC until selected the first channel to link to the group
2. Press the button SELG: the led linked to the selected channel starts blinking
3. Press the button SELC until selected the second channel to link
4. Press the button SELG: the led linked to the selected channel starts blinking
5. Repeat the procedure for all the desired channels: the leds linked are on till the end of the procedure
6. Once selected all the channels wait for the leds to switch off: the group has been stored and it is possible
to display it by pressing the button SELG
When the groups are more than one, to select the desired group proceed as follows:
1. Press the button SELG several times until selected the desired group:
the leds linked to the channels are on for some minutes
2. Press one of the buttons UP, DOWN or STOP to transmit the control
4. TRASMITTER R6-CONTROL

Italian Movements
Italian Movements
12
5. REPLACING BATTERY
6. PROTECTION OF THE ENVIRONMENT
To delete all the groups stored proceed as follows:
1. Press and release the button SELG: the last group used is displayed by the leds.
2. Before all the leds switch off, press and keep pressed the button SELC and at the same time press the
button SELG
3. Keep pressed both the buttons for some seconds until the leds switch off: the groups have been deleted
4.4 Functioning of the button PROG and DIP-SWITCHES
The button PROG and the DIPSWITCHES program the functions of the control units controlled by the
transmitters R-CONTROL. Read carefully the section “PROGRAMMING OF THE FUNCTIONS BY R-CONTROL
TRANSMITTERS” in the handbook of the control unit or in the one of the tubular motor with integrated
electronic card.
Replace the battery when the radio range power decrease or the led light intensity becomes too feeble. Open
the door of the battery compartment and replace the two batteries respecting the polarity shown by picture 2.
Batteries contain pollutant elements, must be disposed of in accordance with environmental regulations
(Fratelli Comunello S.p.A. advise to use a specific disposal system).Transmitter contains pollutant elements
too; follow the same procedure to dispose.
Should the batteries lose electrolytic substances, please replace them immediately avoiding with care any
contact with such substances.

Italian Movements
Italian Movements
13
ENGLISH
7. GUARANTEE
The manufacturer guarantees the correct operation of the trasmitter.
The manufacturer undertakes to replace parts which are faulty due to manufacturing faults or defects,
according to that laid down by Article 1490 of the Italian Civil Code. The guarantee covers the products or
individual parts for a period of 36 months from date of purchase.
This is valid if the purchaser is able to show the purchase receipt and has satisfied the agreed conditions of
payment.
The guarantee of correct operation of the trasmitter issued by the manufacturer means that the manufacturer
undertakes to repair or replace free of charge, in the shortest time possible, those parts that have become
faulty due to defects in construction or material defects during the period of the guarantee.
The purchaser cannot claim the right to any compensation for any damages, direct or indirect, or to other
costs.
The guarantee does not cover parts which are fragile or exposed to wear and tear, or to corrosive process
agents, etc.
The manufacturer cannot be held responsible for the guarantee if the product has been mishandled,
disassembled, had its label removed, or exhibits evidence of impact or other factors.
Attempts at repair by third parties who have not been authorised by the manufacturer will cause the
guarantee to become invalid.
8. DIRECTIVE CONFORMITY

R-CONTROL
FRAME AUTOMATION
Italian Movements
Italian Movements
Fratelli Comunello S.p.A.,
Via Cassola, 64 - 36027 Rosà (Vicenza), Italy.
Tel. [phone] - Fax [phone]
www.comunello.com/mowin
code: 91300105 / VS. 00 / Print 02-2011