Conrad Electronic RC Logger R8 User manual

89102RC
Operating instructions
M2
RC Logger R8 Radio System
VRA VRB
SWA
1
2
SWD
1
2
SWA
1
2
UP
DOWN
OK
CANCEL
POWER
SWC
1
2
3
SWB
1
2
3

2

3
1. INTRODUCTION ....................................................................5
2. DELIVERY CONTENTS..........................................................5
3. MODULES .............................................................................5
4. LATEST OPERATING INSTRUCTIONS ..................................6
5. SYMBOLS..............................................................................6
6. INTENDED USE ....................................................................6
7. SAFETY INSTRUCTIONS.......................................................7
7.1 Persons/Product .................................................................................7
7.2 Radio signal ........................................................................................7
7.3 Before commissioning.........................................................................7
7.4 During operation .................................................................................8
7.5 Batteries..............................................................................................8
7.6 Miscellaneous .....................................................................................8
8. UNPACKING..........................................................................8
9. PARTS AND COMPONENTS.................................................9
10. RECEIVER (RX)....................................................................10
10.1 Bind transmitter and receiver............................................................10
10.1.1 PPM port on NovaX350..................................................10
10.1.2 External power source....................................................11
10.2 Receiver statuses .............................................................................11
11. TRANSMITTER....................................................................11
11.1 Batteries............................................................................................11
11.2 Basic functions..................................................................................11
11.2.1 Turning the transmitter on and off...................................11
11.2.2 Home screen ..................................................................12
11.2.3 Main menu......................................................................12
11.2.4 Backlight .........................................................................13
11.2.5 LCD brightness...............................................................13
11.3 Telemetry data ..................................................................................13
11.4 System settings.................................................................................13
11.4.1 Selecting a model ...........................................................13
11.4.2 Naming a model..............................................................13
11.4.3 Copying a model.............................................................13
11.4.4 Resetting a model...........................................................14
11.4.5 RX setup.........................................................................14
11.4.6 Trainer mode...................................................................14
11.4.7 Student mode .................................................................15
11.4.8 Timer settings .................................................................15
11.4.9 Alarm settings.................................................................15
11.4.10 Firmware version ............................................................15
11.4.11 Firmware update.............................................................16
11.4.12 Factory reset...................................................................16
11.5 Functions settings.............................................................................16
11.5.1 Reversing channels ........................................................16
11.5.2 End points.......................................................................16
11.5.3 Display............................................................................17
TABLE OF CONTENTS

4
11.5.4 Auxiliary channels...........................................................17
11.5.5 Subtrim ...........................................................................18
11.6 Trimming...........................................................................................18
11.7 Direction of antennas during operation.............................................18
11.8 Channel learning...............................................................................18
11.8.1 Auxiliary switch SWD......................................................18
12. MAINTENANCE, CARE AND REPAIR.................................19
12.1 Removing the throttle spring.............................................................19
13. DISPOSAL............................................................................22
13.1 General .............................................................................................22
13.2 Batteries............................................................................................22
14. PRODUCT SUPPORT...........................................................22
15. TECHNICAL DATA...............................................................22
15.1 Transmitter (Tx) ................................................................................22
15.2 Receiver (Rx)....................................................................................22
16. DECLARATION OF CONFORMITY......................................23
17. FCC COMPLIANCE STATEMENT........................................23
18. LEGAL NOTES .....................................................................23

Introduction | 5
1. INTRODUCTION
Dear customer,
Thank you for making the excellent decision to purchase this RC Logger®product. You now
have a high-quality product with a name that represents outstanding products.
This product complies with the applicable National and European standards and
regulations. We kindly request the user to follow the operating instructions, to preserve
this condition and to ensure safe operation! These operating instructions relate to this
product. They contain important notices on commissioning and handling. Please take this
into consideration when you pass the product on to third parties.
Please keep these instructions for future reference!
All company names and product designations contained herein are trademarks of the
respective owners. All rights reserved.
We wish you a great deal of enjoyment with your new RC Logger®product!
From here onwards the RC Logger R8 Radio transmitter is
simply referred to as »Transmitter and the RC Logger R8
Radio receiver as »Receiver.
2. DELIVERY CONTENTS
1x Transmitter
1x PPM Receiver
1x PPM cable
1x Telemetry cable
1x Binding cable
1x USB cable (Trainer port to A-type USB plug)
1x Metal plate
1x Operating instructions
3. MODULES
The operating instructions have been designed in a fashion that you as the
end user can easily navigate them and operate the product safely and to
your full satisfaction. For easier handling, we have divided up the operating
instructions/maintenance manuals into different modules.
Each set of instructions is labelled with its corresponding MODULE INDICATOR in the
right bottom corner on the cover page (e.g. M2). These indicators are used when cross-
referring to other modules.

6| Latest Operating Instructions
4. LATEST OPERATING INSTRUCTIONS
ENGLISH: Please download the latest version of
the operating instructions from our website at
www.rclogger.com. Navigate to the product page and open
the ”Downloads” tab. Click on ”Operating instructions” to
start the download.
DEUTSCH: Bitte laden Sie die neueste Ausgabe der
Bedienungsanleitung von unserer Website herunter, unter
www.rclogger.com. Navigieren Sie bis zur Produktseite
und öffnen Sie das Register ”Downloads” . Klicken Sie auf
”Operating instructions”, um den Download zu starten.
5. SYMBOLS
RED stands for danger and alert. Read these sections
always to avoid accidents and product damage.
BLUE provides you with additional useful information, and
highlights important facts.
GREEN stands for user safety. GREEN also stands for good
practice, protecting your product from damage.
6. INTENDED USE
Use the »Transmitter to control the »NovaX 350 model quad copter, for which it has been
specically designed. The »Transmitter is solely intented for private use in the model
making area. Do not use it for commercial applications.
Any use other than the one described can damage the device. Moreover, this involves
dangers such as short circuit, re and electric shock, etc. Observe the safety information
under all circumstances! The product must not become damp or wet.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting, re,
electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together
with its operating instructions.

Safety Instructions | 7
7. SAFETY INSTRUCTIONS
Read the operating instructions carefully and especially
observe the safety information. If you do not follow the
safety instructions and information on proper handling
in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will
invalidate the warranty/guarantee.
7.1 Persons/Product
> The device is not a toy. Keep it out of the reach of children and pets.
> Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
> If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if the
product:
» is visibly damaged,
» is no longer working properly,
» has been stored for extended periods in poor ambient conditions, or
» has been subjected to any serious transport-related stresses. The product
must not become damp or wet. It uses delicate electronic components which
are sensitive to temperature uctuations and are optimised for a particular
temperature range. Operating temperatures below 0°C must be avoided.
> Do not place the product under any mechanical stress.
> Handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
> Never expose the product to direct sunlight or excessive heat for an extended period
of time.
> Do not place the »Transmitter on the ground when model and »Transmitter are turned
on. In case the »Transmitter tips over, the motors may accidentally start and the model
take off.
> Do not use the product during rainy weather or thunderstorms, in wet conditions, or
when lightning is expected or present.
7.2 Radio signal
> Maintain a distance of at least 20 cm between the »Transmitter’s antenna and persons.
> Large objects, walls, pillars, etc. may reduce the radio signal quality, which may result
in the loss of control over the model. Avoid ying behind such objects.
> High voltage power lines or communication broadcasting towers may inuence the
quality of the radio signal and lead to signal loss. Keep sufcient distance.
> Do not touch or hold the »Transmitter’s antenna during operating. This may
consequently degrade the quality of the transmitted signal.
> The strongest area of transmission is located at the sides of the antenna. As such, do
not point the antenna directly at the model. You may easily correct this situation by
adusting the angle between antenna and model (e.g. Slightly turn the »Transmitter to
the left or right).
7.3 Before commissioning
> Before every ight, check the functional reliability of the product. Watch out for any
visible damage such as defective plug connections or damaged cables and wires.
> Before you y, make sure the batteries have sufcient capacity. If the batteries are
empty, always replace the complete set.
> Before you turn on the »Transmitter, move sticks and set switches to their neutral or
zero positions.
> Always switch on the »Transmitter rst before connecting the battery to the model.
> Test all controls and ensure proper functioning. If »Transmitter and model support "Fail
Safe" functionality run the necessary tests before every ight.

8| Unpacking
7.4 During operation
> Do not take any risks when operating the model. Your own safety and that of your
environment is solely down to you being responsible when dealing with the model.
> Use the product only if your ability to respond is unrestricted. The inuence of tiredness,
alcohol or medication can cause incorrect responses.
> Never switch off the »Transmitter while the model is in use. After landing, always disconnect
the ight battery rst and then switch the »Transmitter off.
7.5 Batteries
> Correct polarity must be observed while inserting the batteries.
> Batteries should be removed from the device if it is not used for a long period of time to
avoid damage through leaking. Leaking or damaged batteries might cause acid burns
when in contact with skin, therefore use suitable protective gloves to handle corrupted
batteries.
> Batteries must be kept out of reach of children. Do not leave batteries lying around.
There is a risk that children or pets swallow them.
> All batteries should be replaced at the same time. Mixing old and new batteries in the
device can lead to battery leakage and device damage.
> Batteries must not be dismantled, short-circuited or thrown into re. Never recharge
non-rechargeable batteries. There is a risk of explosion!
7.6 Miscellaneous
> Consult an expert when in doubt about operation, safety or connection of the device.
> Maintenance, modications and repairs are to be performed exclusively by an expert
or at a qualied shop.
> If you have questions that remain unanswered by these operating instructions, contact
our technical support service or other technical personnel.
8. UNPACKING
> Work on a soft and clean mat.
> Open the box, take out all parts and open the polybags. Place all parts on the mat, but
keep them together as packed in the polybags.

Parts And Components | 9
9. PARTS AND COMPONENTS
VRA VRB
SWA
1
2
SWD
1
2
SWC
1
2
3
UP
DOWN
OK
CANCEL
POWER
SWB
1
2
3
1
2
3
4
5
6
7
8
9
10
111213
r1 r2
r3
r4
r5
14
15
16
17
18
19
20
21
22
Transmitter (Tx)
1 Antenna
2 Handle
3 Analog knob VRB
4 Auxiliary switch (3 pos.) SWA
5 Auxiliary switch (2 pos.) SWD
6 Right control stick
7 Right trims
8 Key
OK
9 Key CANCEL
10 Power switch POWER
11 Battery compartment (underside)
12 LC Display
13 Neck strap attachment
14 Binding key
15 Key
Down
16 Key UP
17 Left trims
18 Left control stick
19 Trainer port
TRAINER (backside)
20 Auxiliary switch (2 pos.)
SWA
21 Auxiliary switch (3 pos.) SWB
22 Analog knob VRA
Receiver (Rx)
r1 Antenna
r2 Indicator light
r3 Header connector
PPM
r4 Header connector TELEMETRY
r5 Header connector BIND

10 | Receiver (rx)
10. RECEIVER (RX)
WARNING! DO NEVER let the bare wire of an antenna
touch PCB boards, carbon fibre parts, electrical/electronic
or metal components. The electronic system may
immediately be destroyed!
10.1 Bind transmitter and receiver
»Transmitter and »Receiver are bound during production.
It may, however, at some point be necessary to manually
intiate the binding. Follow the given instructions.
In simple terms, binding can be described as establishing a communication channel
between »Transmitter and »Receiver.
The »Receiver relies on an external power supply. There are two ways to supply power
during binding:
> PPM port on the »NovaX 350
> External power source (voltage range: 4.0 to 6.5 V/DC):
» USB
» 5 V/DC BEC regulator RC EYE: UBEC (3A) 90012RC (visit www.rclogger.com
for more information)
10.1.1 PPM port on NovaX350
When using the flight battery for binding, always remove
the propellers before you start.
1. Study the »Receiver statuses table in section '10.2 Receiver statuses' on page 11
before you start.
2. Remove the canopy from the »NovaX 350.
3. [If »Receiver is installed] Disconnect the PPM cable from the »Receiver. Doing so
eliminates the likelihood of the »NovaX 350 inadvertently starting up.
4. Turn the »Transmitter off.
5. Install the ight battery into the »NovaX 350.
6. Plug the binding cable into the 3-pin header connector
BIND (r5) on the »Receiver.
7. Connect the PPM cable to the 3-pin header connector PPM (r3) on the »Receiver and
the other end to the PPM_IN socket on the power board.
8. Connect the ight battery and power cable on the »NovaX 350.
9. The RED indicator light on the »Receiver starts to ash fast, indicating the binding
mode.
10. Press and hold the binding key (14) on the »Transmitter and slide the power switch
POWER (10) up to turn the »Transmitter on. The LC display (12) displays “RXBinding..”.
11. Binding is complete when the indicator light (r2) on the »Receiver is solid.
12. Disconnect the »Receiver from the power supply.
13. Turn the »Transmitter off.
14. Remove the binding cable from the »Receiver.
15. Connect the »Receiver to the »NovaX 350's power supply.
16. Turn the »Transmitter on.
17. [If channels are assigned] If you have previously assigned channels, test the
»NovaX 350's functions. If necessary, refer to the corresponding chapters in the
»NovaX 350 operating instructions. If the »NovaX 350 does not function as expected
repeat the binding procedure.